Hi Adrian, Please check my comment inline. Thanks, Sayali -----Original Message----- From: Adrian Hunter [mailto:adrian.hunter@xxxxxxxxx] Sent: Wednesday, June 20, 2018 12:56 PM To: Sayali Lokhande <sayalil@xxxxxxxxxxxxxx>; subhashj@xxxxxxxxxxxxxx; cang@xxxxxxxxxxxxxx; vivek.gautam@xxxxxxxxxxxxxx; rnayak@xxxxxxxxxxxxxx; vinholikatti@xxxxxxxxx; jejb@xxxxxxxxxxxxxxxxxx; martin.petersen@xxxxxxxxxx; asutoshd@xxxxxxxxxxxxxx; evgreen@xxxxxxxxxxxx; riteshh@xxxxxxxxxxxxxx Cc: linux-scsi@xxxxxxxxxxxxxxx; Rob Herring <robh+dt@xxxxxxxxxx>; Mark Rutland <mark.rutland@xxxxxxx>; Mathieu Malaterre <malat@xxxxxxxxxx>; open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS <devicetree@xxxxxxxxxxxxxxx>; open list <linux-kernel@xxxxxxxxxxxxxxx> Subject: Re: [PATCH V3 1/3] scsi: ufs: set the device reference clock setting On 14/06/18 16:03, Sayali Lokhande wrote: > From: Subhash Jadavani <subhashj@xxxxxxxxxxxxxx> > > UFS host supplies the reference clock to UFS device and UFS device > specification allows host to provide one of the 4 frequencies (19.2 > MHz, > 26 MHz, 38.4 MHz, 52 MHz) for reference clock. Host should set the > device reference clock frequency setting in the device based on what > frequency it is supplying to UFS device. > > Signed-off-by: Subhash Jadavani <subhashj@xxxxxxxxxxxxxx> > Signed-off-by: Can Guo <cang@xxxxxxxxxxxxxx> > Signed-off-by: Sayali Lokhande <sayalil@xxxxxxxxxxxxxx> I have repeated my V2 comments below. Please address these when you post V4. Also please provide a change log for each patch version. > --- > .../devicetree/bindings/ufs/ufshcd-pltfrm.txt | 7 +++ > drivers/scsi/ufs/ufs.h | 9 ++++ > drivers/scsi/ufs/ufshcd-pltfrm.c | 24 ++++++++++ > drivers/scsi/ufs/ufshcd.c | 52 ++++++++++++++++++++++ > drivers/scsi/ufs/ufshcd.h | 1 + > 5 files changed, 93 insertions(+) > > diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt > b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt > index c39dfef..4522434 100644 > --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt > +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt > @@ -41,6 +41,12 @@ Optional properties: > -lanes-per-direction : number of lanes available per direction - either 1 or 2. > Note that it is assume same number of lanes is used both > directions at once. If not specified, default is 2 lanes per direction. > +- dev-ref-clk-freq : Specify the device reference clock frequency, must be one of the following: > + 0: 19.2 MHz > + 1: 26 MHz > + 2: 38.4 MHz > + 3: 52 MHz > + Defaults to 26 MHz if not specified. > > Note: If above properties are not defined it can be assumed that the > supply regulators or clocks are always on. > @@ -66,4 +72,5 @@ Example: > freq-table-hz = <100000000 200000000>, <0 0>, <0 0>; > phys = <&ufsphy1>; > phy-names = "ufsphy"; > + dev-ref-clk-freq = <0>; /* reference clock freq: 19.2 MHz */ > }; > diff --git a/drivers/scsi/ufs/ufs.h b/drivers/scsi/ufs/ufs.h index > 14e5bf7..e15deb0 100644 > --- a/drivers/scsi/ufs/ufs.h > +++ b/drivers/scsi/ufs/ufs.h > @@ -378,6 +378,15 @@ enum query_opcode { > UPIU_QUERY_OPCODE_TOGGLE_FLAG = 0x8, > }; > > +/* bRefClkFreq attribute values */ > +enum ref_clk_freq { > + REF_CLK_FREQ_19_2_MHZ = 0x0, > + REF_CLK_FREQ_26_MHZ = 0x1, > + REF_CLK_FREQ_38_4_MHZ = 0x2, > + REF_CLK_FREQ_52_MHZ = 0x3, > + REF_CLK_FREQ_MAX = REF_CLK_FREQ_52_MHZ, > +}; > + > /* Query response result code */ > enum { > QUERY_RESULT_SUCCESS = 0x00, > diff --git a/drivers/scsi/ufs/ufshcd-pltfrm.c > b/drivers/scsi/ufs/ufshcd-pltfrm.c > index e82bde0..6c877f3 100644 > --- a/drivers/scsi/ufs/ufshcd-pltfrm.c > +++ b/drivers/scsi/ufs/ufshcd-pltfrm.c > @@ -221,6 +221,28 @@ static int ufshcd_parse_regulator_info(struct ufs_hba *hba) > return err; > } > > +static void ufshcd_parse_dev_ref_clk_freq(struct ufs_hba *hba) { > + struct device *dev = hba->dev; > + struct device_node *np = dev->of_node; > + int ret; > + > + if (!np) > + return; > + > + ret = of_property_read_u32(np, "dev-ref-clk-freq", > + &hba->dev_ref_clk_freq); This setting is useful for any UFSHC driver. Please move it to ufshcd.c and use device_property_read_u32(). [Sayali]: Ok. Will update this in next patch set. > + if (ret || > + (hba->dev_ref_clk_freq < 0) || u32 cannot be < 0 [Sayali]: Will remove this check. > + (hba->dev_ref_clk_freq > REF_CLK_FREQ_52_MHZ)) { > + dev_err(hba->dev, > + "%s: invalid ref_clk setting = %d, set to default\n", > + __func__, hba->dev_ref_clk_freq); > + /* default setting */ > + hba->dev_ref_clk_freq = REF_CLK_FREQ_26_MHZ; No, the default must be to leave the value unchanged. [Sayali]: As per UFS device specification , bRefClkFreq attribute's default value corresponds to 26 MHz (Manufacturer Default Value). Thus we should set it to default (26MHz) if it's not already set. > + } > +} > + > #ifdef CONFIG_PM > /** > * ufshcd_pltfrm_suspend - suspend power management function @@ > -343,6 +365,8 @@ int ufshcd_pltfrm_init(struct platform_device *pdev, > pm_runtime_set_active(&pdev->dev); > pm_runtime_enable(&pdev->dev); > > + ufshcd_parse_dev_ref_clk_freq(hba); > + > ufshcd_init_lanes_per_dir(hba); > > err = ufshcd_init(hba, mmio_base, irq); diff --git > a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c index > c5b1bf1..4abc7ae 100644 > --- a/drivers/scsi/ufs/ufshcd.c > +++ b/drivers/scsi/ufs/ufshcd.c > @@ -6297,6 +6297,53 @@ static void ufshcd_def_desc_sizes(struct > ufs_hba *hba) } > > /** > + * ufshcd_set_dev_ref_clk - set the device bRefClkFreq > + * @hba: per-adapter instance > + * > + * Read the current value of the bRefClkFreq attribute from device > +and update it > + * if host is supplying different reference clock frequency than one > +mentioned > + * in bRefClkFreq attribute. > + * > + * Returns zero on success, non-zero error value on failure. > + */ > +static int ufshcd_set_dev_ref_clk(struct ufs_hba *hba) { > + int err = 0; > + int ref_clk = -1; > + static const char * const ref_clk_freqs[] = {"19.2 MHz", "26 MHz", > + "38.4 MHz", "52 MHz"}; > + > + err = ufshcd_query_attr_retry(hba, UPIU_QUERY_OPCODE_READ_ATTR, > + QUERY_ATTR_IDN_REF_CLK_FREQ, 0, 0, &ref_clk); > + > + if (err) { > + dev_err(hba->dev, "%s: failed reading bRefClkFreq. err = %d\n", > + __func__, err); > + goto out; > + } > + > + if (ref_clk == hba->dev_ref_clk_freq) > + goto out; /* nothing to update */ > + > + err = ufshcd_query_attr_retry(hba, UPIU_QUERY_OPCODE_WRITE_ATTR, > + QUERY_ATTR_IDN_REF_CLK_FREQ, 0, 0, > + &hba->dev_ref_clk_freq); > + > + if (err) > + dev_err(hba->dev, "%s: bRefClkFreq setting to %s failed\n", > + __func__, ref_clk_freqs[hba->dev_ref_clk_freq]); > + /* > + * It is good to print this out here to debug any later failures > + * related to gear switch. > + */ > + dev_dbg(hba->dev, "%s: bRefClkFreq setting to %s succeeded\n", > + __func__, ref_clk_freqs[hba->dev_ref_clk_freq]); > + > +out: > + return err; > +} > + > +/** > * ufshcd_probe_hba - probe hba to detect device and initialize > * @hba: per-adapter instance > * > @@ -6361,6 +6408,11 @@ static int ufshcd_probe_hba(struct ufs_hba *hba) > "%s: Failed getting max supported power mode\n", > __func__); > } else { > + /* > + * Set the right value to bRefClkFreq before attempting to > + * switch to HS gears. > + */ > + ufshcd_set_dev_ref_clk(hba); > ret = ufshcd_config_pwr_mode(hba, &hba->max_pwr_info.info); > if (ret) { > dev_err(hba->dev, "%s: Failed setting power mode, err = %d\n", > diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h > index 8110dcd..b026ad8 100644 > --- a/drivers/scsi/ufs/ufshcd.h > +++ b/drivers/scsi/ufs/ufshcd.h > @@ -548,6 +548,7 @@ struct ufs_hba { > void *priv; > unsigned int irq; > bool is_irq_enabled; > + u32 dev_ref_clk_freq; > > /* Interrupt aggregation support is broken */ > #define UFSHCD_QUIRK_BROKEN_INTR_AGGR 0x1 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
