On Thu, Jun 07, 2018 at 07:17:46PM +0530, Jagan Teki wrote:
> This patch adds parallel display support for i.MX6DL Mamoj board
> along with relevant backlight through pwm.
>
> LCD power sequence is added by 'Michael Trimarchi'.
>
> Signed-off-by: Simone CIANNI <simone.cianni@xxxxxxxxxx>
> Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@xxxxxxxxxx>
> Signed-off-by: Michael Trimarchi <michael@xxxxxxxxxxxxxxxxxxxx>
> Signed-off-by: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx>
> Reviewed-by: Fabio Estevam <fabio.estevam@xxxxxxx>
> ---
> Changes for v2:
> - collect Fabio r-w-b tag
>
> arch/arm/boot/dts/imx6dl-mamoj.dts | 185 +++++++++++++++++++++++++++++++++++++
> 1 file changed, 185 insertions(+)
>
> diff --git a/arch/arm/boot/dts/imx6dl-mamoj.dts b/arch/arm/boot/dts/imx6dl-mamoj.dts
> index 6b2d29138bed..ed9050c5dbcc 100644
> --- a/arch/arm/boot/dts/imx6dl-mamoj.dts
> +++ b/arch/arm/boot/dts/imx6dl-mamoj.dts
> @@ -6,11 +6,133 @@
>
> /dts-v1/;
>
> +#include <dt-bindings/gpio/gpio.h>
> #include "imx6dl.dtsi"
>
> / {
> model = "BTicino i.MX6DL Mamoj board";
> compatible = "bticino,imx6dl-mamoj", "fsl,imx6dl";
> +
> + backlight_lcd: backlight-lcd {
> + compatible = "pwm-backlight";
> + pwms = <&pwm3 0 25000>; /* 25000ns -> 40kHz */
> + brightness-levels = <0 4 8 16 32 64 128 160 192 224 255>;
> + default-brightness-level = <7>;
> + };
> +
> + lcd_display: disp0 {
'display' for node name.
> + compatible = "fsl,imx-parallel-display";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + interface-pix-fmt = "rgb24";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ipu1_lcdif>;
> + status = "okay";
> +
> + port@0 {
> + reg = <0>;
> +
> + lcd_display_in: endpoint {
> + remote-endpoint = <&ipu1_di0_disp0>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + lcd_display_out: endpoint {
> + remote-endpoint = <&lcd_panel_in>;
> + };
> + };
> + };
> +
> + panel-lcd {
> + compatible = "rocktech,rk070er9427";
> + backlight = <&backlight_lcd>;
> + power-supply = <®_lcd_lr>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_lcd_power>;
> +
> + port {
> + lcd_panel_in: endpoint {
> + remote-endpoint = <&lcd_display_out>;
> + };
> + };
> + };
> +
> + reg_lcd_3v3: regulator-lcd-dvdd {
> + compatible = "regulator-fixed";
> + regulator-name = "lcd-dvdd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio3 1 0>;
> + enable-active-high;
> + startup-delay-us = <21000>;
> + };
> +
> + reg_lcd_power: regulator-lcd-power {
> + compatible = "regulator-fixed";
> + regulator-name = "lcd-enable";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio3 6 0>;
> + enable-active-high;
> + vin-supply = <®_lcd_3v3>;
> + };
> +
> + reg_lcd_vgl: regulator-lcd-vgl {
> + compatible = "regulator-fixed";
> + regulator-name = "lcd-vgl";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>;
> + startup-delay-us = <6000>;
> + enable-active-high;
> + vin-supply = <®_lcd_power>;
> + };
> +
> + reg_lcd_vgh: regulator-lcd-vgh {
> + compatible = "regulator-fixed";
> + regulator-name = "lcd-vgh";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
> + startup-delay-us = <6000>;
> + enable-active-high;
> + vin-supply = <®_lcd_avdd>;
> + };
> +
> + reg_lcd_vcom: regulator-lcd-vcom {
> + compatible = "regulator-fixed";
> + regulator-name = "lcd-vcom";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>;
> + startup-delay-us = <11000>;
> + enable-active-high;
> + vin-supply = <®_lcd_vgh>;
> + };
> +
> + reg_lcd_lr: regulator-lcd-lr {
> + compatible = "regulator-fixed";
> + regulator-name = "lcd-lr";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + vin-supply = <®_lcd_vcom>;
> + };
> +
> + reg_lcd_avdd: regulator-lcd-avdd {
> + compatible = "regulator-fixed";
> + regulator-name = "lcd-avdd";
> + regulator-min-microvolt = <10280000>;
> + regulator-max-microvolt = <10280000>;
> + gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>;
> + startup-delay-us = <6000>;
> + enable-active-high;
> + vin-supply = <®_lcd_vgl>;
> + };
> };
>
> &fec {
> @@ -147,6 +269,16 @@
> };
> };
>
> +&ipu1_di0_disp0 {
> + remote-endpoint = <&lcd_display_in>;
> +};
> +
> +&pwm3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm3>;
> + status = "okay";
> +};
> +
> &uart3 {
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_uart3>;
> @@ -200,6 +332,59 @@
> >;
> };
>
> + pinctrl_ipu1_lcdif: pinctrlipu1lcdif { /* parallel port 24-bit */
> + fsl,pins = <
> + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 /* VDOUT_PCLK */
> + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10
> + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10 /* VDOUT_HSYNC */
> + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10 /* VDOUT_VSYNC */
> + MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04 0x80000000 /* VDOUT_RESET */
Use a proper configuration value rather than relying on what
firmware/reset gives.
> + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
> + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
> + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
> + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
> + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
> + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
> + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
> + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
> + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
> + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
> + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
> + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
> + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
> + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
> + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
> + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
> + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
> + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
> + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
> + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
> + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
> + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
> + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
> + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
> + >;
> + };
> +
> + pinctrl_lcd_power: lcd_power {
The node name and above pinctrlipu1lcdif is not consistent to other
pinctrl nodes.
Shawn
> + fsl,pins = <
> + MX6QDL_PAD_EIM_DA1__GPIO3_IO01 0x40013058 /* EN_LCD33V */
> + MX6QDL_PAD_SD4_DAT5__GPIO2_IO13 0x4001b0b0 /* EN_AVDD */
> + MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x40013058 /* ENVGH */
> + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x40013058 /* ENVGL */
> + MX6QDL_PAD_EIM_DA6__GPIO3_IO06 0x40013058 /* LCD_POWER */
> + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x40013058 /* EN_VCOM_LCD */
> + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x40013058 /* LCD_L_R */
> + MX6QDL_PAD_EIM_DA2__GPIO3_IO02 0x40013058 /* LCD_U_D */
> + >;
> + };
> +
> + pinctrl_pwm3: pwm3grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
> + >;
> + };
> +
> pinctrl_uart3: uart3grp {
> fsl,pins = <
> MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
> --
> 2.14.3
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
