Document the bindings used for the sn65dsi86 DSI to eDP bridge. Changes in v1: - Rephrase the dt-binding descriptions to be more inline with existing bindings (Andrzej Hajda). - Add missing dt-binding that are parsed by corresponding driver (Andrzej Hajda). Changes in v2: - Remove edp panel specific dt-binding entries. Only keep bridge specific entries (Sean Paul). - Remove custom-modes dt entry since its usage is removed from driver also (Sean Paul). - Remove is-pluggable dt entry since this will not be needed anymore (Sean Paul). Changes in v3: - Remove irq-gpio dt entry and instead populate is an interrupt property (Rob Herring). Changes in v4: - Add link to bridge chip datasheet (Stephen Boyd) - Add vpll and vcc regulator supply bindings (Stephen Boyd) - Add ref clk optional dt binding (Stephen Boyd) - Add gpio-controller optional dt binding (Stephen Boyd) Changes in v5: - Use clock property to specify the input refclk (Stephen Boyd). - Update gpio cell and pwm cell numbers (Stephen Boyd). Changes in v6: - Add property to mention the lane mapping scheme and polarity inversion (Stephen Boyd). Changes in v7: - Detail description of lane mapping scheme dt property (Andrzej Hajda/ Rob Herring). - Removed HDP gpio binding, since the bridge uses IRQ signal to determine HPD, and IRQ property is already documented in binding. Changes in v8: - Removed unnecessary explanation of lane mapping and polarity dt property, since these are already explained in media/video-interface dt binidng (Rob Herring). Signed-off-by: Sandeep Panda <spanda@xxxxxxxxxxxxxx> --- .../bindings/display/bridge/ti,sn65dsi86.txt | 90 ++++++++++++++++++++++ 1 file changed, 90 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt new file mode 100644 index 0000000..601454c --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi86.txt @@ -0,0 +1,90 @@ +SN65DSI86 DSI to eDP bridge chip +-------------------------------- + +This is the binding for Texas Instruments SN65DSI86 bridge. +http://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf + +Required properties: +- compatible: Must be "ti,sn65dsi86" +- reg: i2c address of the chip, 0x2d as per datasheet +- enable-gpios: OF device-tree gpio specification for bridge_en pin (active high) + +- vccio-supply: A 1.8V supply that powers up the digital IOs. +- vpll-supply: A 1.8V supply that powers up the displayport PLL. +- vcca-supply: A 1.2V supply that powers up the analog circuits. +- vcc-supply: A 1.2V supply that powers up the digital core. + +Optional properties: +- interrupts: Specifier for the SN65DSI86 interrupt line. + +- ddc-i2c-bus: phandle of the I2C controller used for DDC EDID probing + +- gpio-controller: Marks the device has a GPIO controller. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../../gpio/gpio.txt for more information. +- #pwm-cells : Should be one. See ../../pwm/pwm.txt for description of + the cell formats. + +- clock-names: should be "refclk" +- clocks: Specification for input reference clock. The reference + clock rate must be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz. + +- data-lanes: Specification to describe the logical to physical lane + mapping scheme. See ../../media/video-interface.txt for more + information. +- lane-polarities: Specification to describe the polarity of physical lanes. + See ../../media/video-interface.txt for more information. + +Required nodes: +This device has two video ports. Their connections are modelled using the +OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. + +- Video port 0 for DSI input +- Video port 1 for eDP output + +Example +------- + +edp-bridge@2d { + compatible = "ti,sn65dsi86"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2d>; + + enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>; + interrupt-parent = <&gpio3>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + + vccio-supply = <&pm8916_l17>; + vcca-supply = <&pm8916_l6>; + vpll-supply = <&pm8916_l17>; + vcc-supply = <&pm8916_l6>; + + clock-names = "refclk"; + clocks = <&input_refclk>; + + data-lanes = <2 1 3 0>; + lane-polarities = <0 1 0 1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + edp_bridge_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + + port@1 { + reg = <1>; + + edp_bridge_out: endpoint { + remote-endpoint = <&edp_panel_in>; + }; + }; + }; +} -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
