Hi Can,
On 5/29/2018 10:07 AM, Can Guo wrote:
Add UFS PHY support to make SDM845 UFS work with common PHY framework.
Signed-off-by: Can Guo <cang@xxxxxxxxxxxxxx>
---
drivers/phy/qualcomm/phy-qcom-qmp.c | 200 +++++++++++++++++++++++++++++++++---
drivers/phy/qualcomm/phy-qcom-qmp.h | 15 +++
2 files changed, 203 insertions(+), 12 deletions(-)
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index f779b0f..ee74dcd 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -156,6 +156,11 @@ enum qphy_reg_layout {
[QPHY_PCS_LFPS_RXTERM_IRQ_STATUS] = 0x170,
};
+static const unsigned int sdm845_ufsphy_regs_layout[] = {
+ [QPHY_START_CTRL] = 0x00,
+ [QPHY_PCS_READY_STATUS] = 0x160,
+};
+
static const struct qmp_phy_init_tbl msm8996_pcie_serdes_tbl[] = {
QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x1c),
QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
@@ -601,6 +606,83 @@ enum qphy_reg_layout {
QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG2, 0x60),
};
+static const struct qmp_phy_init_tbl sdm845_ufsphy_serdes_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x02),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_BG_TIMER, 0x0a),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0xd5),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_RESETSM_CNTRL, 0x20),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_CTRL, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x05),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_INITVAL1, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_INITVAL2, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE0, 0xda),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE0, 0x01),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0xff),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x0c),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE1, 0x98),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE1, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE1, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE1, 0x36),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE1, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE1, 0xc1),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE1, 0x00),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE1, 0x32),
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE1, 0x0f),
+
+ /* Rate B */
+ QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x44),
+};
+
+static const struct qmp_phy_init_tbl sdm845_ufsphy_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_LANE_MODE_1, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_RX, 0x07),
+};
+
+static const struct qmp_phy_init_tbl sdm845_ufsphy_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_LVL, 0x24),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x0f),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x1e),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_INTERFACE_MODE, 0x40),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_TERM_BW, 0x5b),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x06),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x1b),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SVS_SO_GAIN_HALF, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SVS_SO_GAIN_QUARTER, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SVS_SO_GAIN, 0x04),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x4b),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_PI_CONTROLS, 0x81),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_COUNT_LOW, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_MODE_00, 0x59),
+};
+
+static const struct qmp_phy_init_tbl sdm845_ufsphy_pcs_tbl[] = {
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_CTRL2, 0x6e),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TX_LARGE_AMP_DRV_LVL, 0x0a),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TX_SMALL_AMP_DRV_LVL, 0x02),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SYM_RESYNC_CTRL, 0x03),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_TX_MID_TERM_CTRL1, 0x43),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_CTRL1, 0x0f),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_MIN_HIBERN8_TIME, 0x9a),
+ QMP_PHY_INIT_CFG(QPHY_V3_PCS_MULTI_LANE_CTRL1, 0x02),
+};
/* struct qmp_phy_cfg - per-PHY initialization config */
struct qmp_phy_cfg {
@@ -649,9 +731,14 @@ struct qmp_phy_cfg {
/* true, if PHY has a separate DP_COM control block */
bool has_phy_dp_com_ctrl;
+ /* true, if PHY has secondary tx/rx lanes to be configured */
+ bool is_dual_lane_phy;
Separate out this change to a new patch please.
/* Register offset of secondary tx/rx lanes for USB DP combo PHY */
unsigned int tx_b_lane_offset;
unsigned int rx_b_lane_offset;
+
+ /* true, if PCS block has no separate SW_RESET register */
+ bool no_pcs_sw_reset;
};
/**
@@ -748,6 +835,10 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
"aux", "cfg_ahb", "ref", "com_aux",
};
+static const char * const sdm845_ufs_phy_clk_l[] = {
+ "ref", "ref_aux",
+};
+
/* list of resets */
static const char * const msm8996_pciephy_reset_l[] = {
"phy", "common", "cfg",
@@ -758,7 +849,7 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
};
/* list of regulators */
-static const char * const msm8996_phy_vreg_l[] = {
+static const char * const qmp_phy_vreg_l[] = {
These changes are not related to ufs, so better keep all these in a separate
patch, say 'cleanup', as mentioned above.
"vdda-phy", "vdda-pll",
};
@@ -778,8 +869,8 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
.num_clks = ARRAY_SIZE(msm8996_phy_clk_l),
.reset_list = msm8996_pciephy_reset_l,
.num_resets = ARRAY_SIZE(msm8996_pciephy_reset_l),
- .vreg_list = msm8996_phy_vreg_l,
- .num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
So this changes and other vreg changes in cfg goes to the separate patch.
.regs = pciephy_regs_layout,
.start_ctrl = PCS_START | PLL_READY_GATE_EN,
@@ -809,8 +900,8 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
.num_clks = ARRAY_SIZE(msm8996_phy_clk_l),
.reset_list = msm8996_usb3phy_reset_l,
.num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
- .vreg_list = msm8996_phy_vreg_l,
- .num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
.regs = usb3phy_regs_layout,
.start_ctrl = SERDES_START | PCS_START,
@@ -870,8 +961,8 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
.num_clks = ARRAY_SIZE(qmp_v3_phy_clk_l),
.reset_list = msm8996_usb3phy_reset_l,
.num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
- .vreg_list = msm8996_phy_vreg_l,
- .num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
.regs = qmp_v3_usb3phy_regs_layout,
.start_ctrl = SERDES_START | PCS_START,
@@ -883,6 +974,7 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
.pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
.has_phy_dp_com_ctrl = true,
+ .is_dual_lane_phy = true,
This too goes to the new patch.
.tx_b_lane_offset = 0x400,
.rx_b_lane_offset = 0x400,
};
@@ -903,8 +995,8 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
.num_clks = ARRAY_SIZE(qmp_v3_phy_clk_l),
.reset_list = msm8996_usb3phy_reset_l,
.num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l),
- .vreg_list = msm8996_phy_vreg_l,
- .num_vregs = ARRAY_SIZE(msm8996_phy_vreg_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
.regs = qmp_v3_usb3phy_regs_layout,
.start_ctrl = SERDES_START | PCS_START,
@@ -916,6 +1008,35 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
.pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX,
};
+static const struct qmp_phy_cfg sdm845_ufsphy_cfg = {
+ .type = PHY_TYPE_UFS,
+ .nlanes = 2,
+
+ .serdes_tbl = sdm845_ufsphy_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(sdm845_ufsphy_serdes_tbl),
+ .tx_tbl = sdm845_ufsphy_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(sdm845_ufsphy_tx_tbl),
+ .rx_tbl = sdm845_ufsphy_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(sdm845_ufsphy_rx_tbl),
+ .pcs_tbl = sdm845_ufsphy_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(sdm845_ufsphy_pcs_tbl),
+ .clk_list = sdm845_ufs_phy_clk_l,
+ .num_clks = ARRAY_SIZE(sdm845_ufs_phy_clk_l),
+ .vreg_list = qmp_phy_vreg_l,
+ .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
+ .regs = sdm845_ufsphy_regs_layout,
+
+ .start_ctrl = SERDES_START,
+ .pwrdn_ctrl = SW_PWRDN,
+ .mask_pcs_ready = PCS_READY,
+
+ .is_dual_lane_phy = true,
+ .tx_b_lane_offset = 0x400,
+ .rx_b_lane_offset = 0x400,
+
+ .no_pcs_sw_reset = true,
+};
+
static void qcom_qmp_phy_configure(void __iomem *base,
const unsigned int *regs,
const struct qmp_phy_init_tbl tbl[],
@@ -938,7 +1059,9 @@ static void qcom_qmp_phy_configure(void __iomem *base,
static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
{
const struct qmp_phy_cfg *cfg = qmp->cfg;
+ struct qmp_phy *qphy = qmp->phys[0];
void __iomem *serdes = qmp->serdes;
+ void __iomem *pcs = qphy->pcs;
void __iomem *dp_com = qmp->dp_com;
int ret, i;
@@ -1114,18 +1237,27 @@ static int qcom_qmp_phy_init(struct phy *phy)
/* Tx, Rx, and PCS configurations */
qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num);
/* Configuration for other LANE for USB-DP combo PHY */
- if (cfg->has_phy_dp_com_ctrl)
+ if (cfg->is_dual_lane_phy)
qcom_qmp_phy_configure(tx + cfg->tx_b_lane_offset, cfg->regs,
cfg->tx_tbl, cfg->tx_tbl_num);
qcom_qmp_phy_configure(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num);
- if (cfg->has_phy_dp_com_ctrl)
+ if (cfg->is_dual_lane_phy)
And these couple of changes too to the new patch. This helps in
bisecting in the
time of issue.
qcom_qmp_phy_configure(rx + cfg->rx_b_lane_offset, cfg->regs,
cfg->rx_tbl, cfg->rx_tbl_num);
qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
/*
+ * UFS PHY requires the deassert of software reset before serdes start.
+ * For UFS PHY that has not software reset control bits in its address
+ * space, it should skip starting serdes here. UFS PHY Serdes shall
+ * start when UFS explicitly calls PHY power on.
+ */
+ if ((cfg->type == PHY_TYPE_UFS) && cfg->no_pcs_sw_reset)
+ goto out;
+
+ /*
* Pull out PHY from POWER DOWN state.
* This is active low enable signal to power-down PHY.
*/
@@ -1154,6 +1286,7 @@ static int qcom_qmp_phy_init(struct phy *phy)
}
qmp->phy_initialized = true;
+out:
return ret;
err_pcs_ready:
@@ -1176,7 +1309,8 @@ static int qcom_qmp_phy_exit(struct phy *phy)
clk_disable_unprepare(qphy->pipe_clk);
/* PHY reset */
- qphy_setbits(qphy->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
+ if (!cfg->no_pcs_sw_reset)
+ qphy_setbits(qphy->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET);
/* stop SerDes and Phy-Coding-Sublayer */
qphy_clrbits(qphy->pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
@@ -1194,6 +1328,44 @@ static int qcom_qmp_phy_exit(struct phy *phy)
return 0;
}
+static int qcom_qmp_phy_poweron(struct phy *phy)
+{
+ struct qmp_phy *qphy = phy_get_drvdata(phy);
+ struct qcom_qmp *qmp = qphy->qmp;
+ const struct qmp_phy_cfg *cfg = qmp->cfg;
+ void __iomem *pcs = qphy->pcs;
+ void __iomem *status;
+ unsigned int mask, val;
+ int ret = 0;
+
+ if (cfg->type != PHY_TYPE_UFS)
+ return 0;
+
+ /*
+ * For UFS PHY that has not software reset control, serdes start
+ * should only happen when UFS driver explicitly calls phy_power_on
+ * after it deasserts software reset.
+ */
+ if (cfg->no_pcs_sw_reset && !qmp->phy_initialized &&
+ (qmp->init_count !=0)) {
+ /* start SerDes and Phy-Coding-Sublayer */
+ qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
+
+ status = pcs + cfg->regs[QPHY_PCS_READY_STATUS];
+ mask = cfg->mask_pcs_ready;
+
+ ret = readl_poll_timeout(status, val, !(val & mask), 1,
+ PHY_INIT_COMPLETE_TIMEOUT);
+ if (ret) {
+ dev_err(qmp->dev, "phy initialization timed-out\n");
+ return ret;
+ }
+ qmp->phy_initialized = true;
+ }
+
+ return ret;
+}
+
static int qcom_qmp_phy_set_mode(struct phy *phy, enum phy_mode mode)
{
struct qmp_phy *qphy = phy_get_drvdata(phy);
@@ -1423,6 +1595,7 @@ static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np)
static const struct phy_ops qcom_qmp_phy_gen_ops = {
.init = qcom_qmp_phy_init,
.exit = qcom_qmp_phy_exit,
+ .power_on = qcom_qmp_phy_poweron,
.set_mode = qcom_qmp_phy_set_mode,
.owner = THIS_MODULE,
};
@@ -1528,6 +1701,9 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
}, {
.compatible = "qcom,sdm845-qmp-usb3-uni-phy",
.data = &qmp_v3_usb3_uniphy_cfg,
+ }, {
+ .compatible = "qcom,sdm845-qmp-ufs-phy",
+ .data = &sdm845_ufsphy_cfg,
},
{ },
};
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index 5d78d43..d201cc3 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -184,6 +184,8 @@
#define QSERDES_V3_COM_VCO_TUNE2_MODE0 0x0f8
#define QSERDES_V3_COM_VCO_TUNE1_MODE1 0x0fc
#define QSERDES_V3_COM_VCO_TUNE2_MODE1 0x100
+#define QSERDES_V3_COM_VCO_TUNE_INITVAL1 0x104
+#define QSERDES_V3_COM_VCO_TUNE_INITVAL2 0x108
#define QSERDES_V3_COM_VCO_TUNE_TIMER1 0x11c
#define QSERDES_V3_COM_VCO_TUNE_TIMER2 0x120
#define QSERDES_V3_COM_CLK_SELECT 0x138
@@ -211,8 +213,13 @@
/* Only for QMP V3 PHY - RX registers */
#define QSERDES_V3_RX_UCDR_SO_GAIN_HALF 0x00c
#define QSERDES_V3_RX_UCDR_SO_GAIN 0x014
+#define QSERDES_V3_RX_UCDR_SVS_SO_GAIN_HALF 0x024
+#define QSERDES_V3_RX_UCDR_SVS_SO_GAIN_QUARTER 0x028
+#define QSERDES_V3_RX_UCDR_SVS_SO_GAIN 0x02c
#define QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN 0x030
#define QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE 0x034
+#define QSERDES_V3_RX_UCDR_FASTLOCK_COUNT_LOW 0x03c
+#define QSERDES_V3_RX_UCDR_PI_CONTROLS 0x044
#define QSERDES_V3_RX_RX_TERM_BW 0x07c
#define QSERDES_V3_RX_VGA_CAL_CNTRL1 0x0bc
#define QSERDES_V3_RX_VGA_CAL_CNTRL2 0x0c0
@@ -239,6 +246,8 @@
#define QPHY_V3_PCS_TXMGN_V3 0x018
#define QPHY_V3_PCS_TXMGN_V4 0x01c
#define QPHY_V3_PCS_TXMGN_LS 0x020
+#define QPHY_V3_PCS_TX_LARGE_AMP_DRV_LVL 0x02c
+#define QPHY_V3_PCS_TX_SMALL_AMP_DRV_LVL 0x034
#define QPHY_V3_PCS_TXDEEMPH_M6DB_V0 0x024
#define QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0 0x028
#define QPHY_V3_PCS_TXDEEMPH_M6DB_V1 0x02c
@@ -275,6 +284,12 @@
#define QPHY_V3_PCS_FLL_CNT_VAL_L 0x0cc
#define QPHY_V3_PCS_FLL_CNT_VAL_H_TOL 0x0d0
#define QPHY_V3_PCS_FLL_MAN_CODE 0x0d4
+#define QPHY_V3_PCS_RX_SYM_RESYNC_CTRL 0x134
+#define QPHY_V3_PCS_RX_MIN_HIBERN8_TIME 0x138
+#define QPHY_V3_PCS_RX_SIGDET_CTRL1 0x13c
+#define QPHY_V3_PCS_RX_SIGDET_CTRL2 0x140
+#define QPHY_V3_PCS_TX_MID_TERM_CTRL1 0x1bc
+#define QPHY_V3_PCS_MULTI_LANE_CTRL1 0x1c4
#define QPHY_V3_PCS_RX_SIGDET_LVL 0x1d8
#define QPHY_V3_PCS_REFGEN_REQ_CONFIG1 0x20c
#define QPHY_V3_PCS_REFGEN_REQ_CONFIG2 0x210
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
