Add the pins used by the LCD controller, the panel-info and display-timings
information for the MIDAS displays connected to the board. There are
two displays in the board, and these, are connected to the LCD controller
through a FPGA, so the timings and the resolution is what expects the FPGA,
not the MIDAS displays.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@xxxxxxxxxxxxx>
---
arch/arm/boot/dts/am335x-sl50.dts | 69 ++++++++++++++++++++++++++++++-
1 file changed, 68 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/am335x-sl50.dts b/arch/arm/boot/dts/am335x-sl50.dts
index 58fe84f2ec8b..ea047b85b726 100644
--- a/arch/arm/boot/dts/am335x-sl50.dts
+++ b/arch/arm/boot/dts/am335x-sl50.dts
@@ -111,6 +111,45 @@
};
};
+ panel: lcd_panel {
+ compatible = "ti,tilcdc,panel";
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_pins>;
+
+ panel-info {
+ ac-bias = <255>;
+ ac-bias-intrpt = <0>;
+ dma-burst-sz = <16>;
+ bpp = <16>;
+ fdd = <0x80>;
+ tft-alt-mode = <0>;
+ mono-8bit-mode = <0>;
+ sync-edge = <0>;
+ sync-ctrl = <1>;
+ raster-order = <0>;
+ fifo-th = <0>;
+ };
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: 960x128 {
+ clock-frequency = <18000000>;
+ hactive = <960>;
+ vactive = <272>;
+
+ hback-porch = <40>;
+ hfront-porch = <16>;
+ hsync-len = <24>;
+ hsync-active = <0>;
+
+ vback-porch = <3>;
+ vfront-porch = <8>;
+ vsync-len = <4>;
+ vsync-active = <0>;
+ };
+ };
+ };
+
sound {
compatible = "ti,da830-evm-audio";
ti,model = "AM335x-SL50";
@@ -166,6 +205,31 @@
>;
};
+ lcd_pins: pinmux_lcd_pins {
+ pinctrl-single,pins = <
+ AM33XX_IOPAD(0x8a0, PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */
+ AM33XX_IOPAD(0x8a4, PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */
+ AM33XX_IOPAD(0x8a8, PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */
+ AM33XX_IOPAD(0x8ac, PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */
+ AM33XX_IOPAD(0x8b0, PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */
+ AM33XX_IOPAD(0x8b4, PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */
+ AM33XX_IOPAD(0x8b8, PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */
+ AM33XX_IOPAD(0x8bc, PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */
+ AM33XX_IOPAD(0x8c0, PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */
+ AM33XX_IOPAD(0x8c4, PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */
+ AM33XX_IOPAD(0x8c8, PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */
+ AM33XX_IOPAD(0x8cc, PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */
+ AM33XX_IOPAD(0x8d0, PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */
+ AM33XX_IOPAD(0x8d4, PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */
+ AM33XX_IOPAD(0x8d8, PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */
+ AM33XX_IOPAD(0x8dc, PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */
+ AM33XX_IOPAD(0x8e0, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_vsync.lcd_vsync */
+ AM33XX_IOPAD(0x8e4, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_hsync.lcd_hsync */
+ AM33XX_IOPAD(0x8e8, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_pclk.lcd_pclk */
+ AM33XX_IOPAD(0x8ec, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */
+ >;
+ };
+
led_pins: pinmux_led_pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE7) /* gpmc_a5.gpio1_21 */
@@ -323,7 +387,6 @@
lwb_pins: pinmux_lwb_pins {
pinctrl-single,pins = <
AM33XX_IOPAD(0x9a4, PIN_OUTPUT | MUX_MODE7) /* SoundPA_en - mcasp0_fsr.gpio3_19 */
- AM33XX_IOPAD(0x828, PIN_OUTPUT | MUX_MODE7) /* nKbdOnC - gpmc_ad10.gpio0_26 */
AM33XX_IOPAD(0x830, PIN_INPUT_PULLUP | MUX_MODE7) /* nKbdInt - gpmc_ad12.gpio1_12 */
AM33XX_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE7) /* nKbdReset - gpmc_ad13.gpio1_13 */
AM33XX_IOPAD(0x844, PIN_INPUT_PULLUP | MUX_MODE7) /* USB1_enPower - gpmc_a1.gpio1_17 */
@@ -595,3 +658,7 @@
pinctrl-names = "default";
pinctrl-0 = <&ehrpwm1_pins>;
};
+
+&lcdc {
+ status = "okay";
+};
--
2.17.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
