The helios4 is a Armada388 based nas board designed by SolidRun and based on their SOM. It is sold by kobol.io the dts file came from https://raw.githubusercontent.com/armbian/build/master/patch/kernel/mvebu-default/95-helios4-device-tree.patch I added a SPDX license line to match the clearfog it says it was based on and a compatible line for "kobol,helios4" Signed-off-by: Dennis Gilmore <dennis@xxxxxxxx> --- changes since first submission change solidrun to kobol in compatible line based on feedback changes since v2 remove commented out nodes based on feedback changes since v3 update copyright info for the dts based on a request from kobol --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/armada-388-helios4.dts | 313 +++++++++++++++++++++++ 2 files changed, 314 insertions(+) create mode 100644 arch/arm/boot/dts/armada-388-helios4.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 7e2424957809..490bfd586198 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1123,6 +1123,7 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \ armada-388-clearfog-pro.dtb \ armada-388-db.dtb \ armada-388-gp.dtb \ + armada-388-helios4.dtb \ armada-388-rd.dtb dtb-$(CONFIG_MACH_ARMADA_39X) += \ armada-398-db.dtb diff --git a/arch/arm/boot/dts/armada-388-helios4.dts b/arch/arm/boot/dts/armada-388-helios4.dts new file mode 100644 index 000000000000..705adfa8c680 --- /dev/null +++ b/arch/arm/boot/dts/armada-388-helios4.dts @@ -0,0 +1,313 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Device Tree file for Helios4 + * based on SolidRun Clearfog revision A1 rev 2.0 (88F6828) + * + * Copyright (C) 2017 Aditya Prayoga <aditya@xxxxxxxx> + * + */ + +/dts-v1/; +#include "armada-388.dtsi" +#include "armada-38x-solidrun-microsom.dtsi" + +/ { + model = "Helios4"; + compatible = "kobol,helios4", "marvell,armada388", + "marvell,armada385", "marvell,armada380"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x80000000>; /* 2 GB */ + }; + + aliases { + /* So that mvebu u-boot can update the MAC addresses */ + ethernet1 = ð0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reg_12v: regulator-12v { + compatible = "regulator-fixed"; + regulator-name = "power_brick_12V"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + vin-supply = <®_12v>; + }; + + reg_5p0v_hdd: regulator-5v-hdd { + compatible = "regulator-fixed"; + regulator-name = "5V_HDD"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <®_12v>; + }; + + reg_5p0v_usb: regulator-5v-usb { + compatible = "regulator-fixed"; + regulator-name = "USB-PWR"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + enable-active-high; + gpio = <&expander0 6 GPIO_ACTIVE_HIGH>; + vin-supply = <®_12v>; + }; + + system-leds { + compatible = "gpio-leds"; + status-led { + label = "helios4:green:status"; + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + default-state = "on"; + }; + + fault-led { + label = "helios4:red:fault"; + gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + }; + + io-leds { + compatible = "gpio-leds"; + sata1-led { + label = "helios4:green:ata1"; + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; + linux,default-trigger = "ata1"; + default-state = "off"; + }; + sata2-led { + label = "helios4:green:ata2"; + gpios = <&gpio1 18 GPIO_ACTIVE_LOW>; + linux,default-trigger = "ata2"; + default-state = "off"; + }; + sata3-led { + label = "helios4:green:ata3"; + gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + linux,default-trigger = "ata3"; + default-state = "off"; + }; + sata4-led { + label = "helios4:green:ata4"; + gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; + linux,default-trigger = "ata4"; + default-state = "off"; + }; + usb-led { + label = "helios4:green:usb"; + gpios = <&gpio1 22 GPIO_ACTIVE_LOW>; + linux,default-trigger = "usb-host"; + default-state = "off"; + }; + }; + + fan1: j10-pwm { + compatible = "pwm-fan"; + pwms = <&gpio1 9 40000>; /* Target freq:25 kHz */ + }; + + fan2: j17-pwm { + compatible = "pwm-fan"; + pwms = <&gpio1 23 40000>; /* Target freq:25 kHz */ + }; + + usb2_phy: usb2-phy { + compatible = "usb-nop-xceiv"; + vbus-regulator = <®_5p0v_usb>; + }; + + usb3_phy: usb3-phy { + compatible = "usb-nop-xceiv"; + }; + + soc { + internal-regs { + i2c@11000 { + clock-frequency = <400000>; + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + status = "okay"; + + /* + * PCA9655 GPIO expander, up to 1MHz clock. + * 0-Board Revision bit 0 # + * 1-Board Revision bit 1 # + * 5-USB3 overcurrent + * 6-USB3 power + */ + expander0: gpio-expander@20 { + /* + * This is how it should be: + * compatible = "onnn,pca9655", + * "nxp,pca9555"; + * but you can't do this because of + * the way I2C works. + */ + compatible = "nxp,pca9555"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&pca0_pins>; + interrupt-parent = <&gpio0>; + interrupts = <23 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + + board_rev_bit_0 { + gpio-hog; + gpios = <0 GPIO_ACTIVE_LOW>; + input; + line-name = "board-rev-0"; + }; + board_rev_bit_1 { + gpio-hog; + gpios = <1 GPIO_ACTIVE_LOW>; + input; + line-name = "board-rev-1"; + }; + usb3_ilimit { + gpio-hog; + gpios = <5 GPIO_ACTIVE_HIGH>; + input; + line-name = "usb-overcurrent-status"; + }; + }; + + temp_sensor: temp@4c { + compatible = "ti,lm75"; + reg = <0x4c>; + vcc-supply = <®_3p3v>; + }; + }; + + i2c@11100 { + /* + * External I2C Bus for user peripheral + */ + clock-frequency = <400000>; + pinctrl-0 = <&helios_i2c1_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + sata@a8000 { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + sata0: sata-port@0 { + reg = <0>; + }; + + sata1: sata-port@1 { + reg = <1>; + }; + }; + + sata@e0000 { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + sata2: sata-port@0 { + reg = <0>; + }; + + sata3: sata-port@1 { + reg = <1>; + }; + }; + + spi@10680 { + pinctrl-0 = <&spi1_pins + µsom_spi1_cs_pins>; + pinctrl-names = "default"; + status = "okay"; + }; + + sdhci@d8000 { + bus-width = <4>; + cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + no-1-8-v; + pinctrl-0 = <&helios_sdhci_pins + &helios_sdhci_cd_pins>; + pinctrl-names = "default"; + status = "okay"; + vmmc = <®_3p3v>; + wp-inverted; + }; + + usb@58000 { + usb-phy = <&usb2_phy>; + status = "okay"; + }; + + usb3@f0000 { + status = "okay"; + }; + + usb3@f8000 { + status = "okay"; + }; + + pinctrl@18000 { + pca0_pins: pca0-pins { + marvell,pins = "mpp23"; + marvell,function = "gpio"; + }; + microsom_phy0_int_pins: microsom-phy0-int-pins { + marvell,pins = "mpp18"; + marvell,function = "gpio"; + }; + helios_i2c1_pins: i2c1-pins { + marvell,pins = "mpp26", "mpp27"; + marvell,function = "i2c1"; + }; + helios_sdhci_cd_pins: helios-sdhci-cd-pins { + marvell,pins = "mpp20"; + marvell,function = "gpio"; + }; + helios_sdhci_pins: helios-sdhci-pins { + marvell,pins = "mpp21", "mpp28", + "mpp37", "mpp38", + "mpp39", "mpp40"; + marvell,function = "sd0"; + }; + helios_led_pins: helios-led-pins { + marvell,pins = "mpp24", "mpp25", + "mpp49", "mpp50", + "mpp52", "mpp53", + "mpp54"; + marvell,function = "gpio"; + }; + helios_fan_pins: helios-fan-pins { + marvell,pins = "mpp41", "mpp43", + "mpp48", "mpp55"; + marvell,function = "gpio"; + }; + microsom_spi1_cs_pins: spi1-cs-pins { + marvell,pins = "mpp59"; + marvell,function = "spi1"; + }; + }; + }; + }; +}; -- 2.17.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
