On Fri, 1 Jun 2018 00:16:34 +0200
Stefan Agner <stefan@xxxxxxxx> wrote:
> This adds the devicetree binding for the Tegra 2 NAND flash
> controller.
>
> Signed-off-by: Lucas Stach <dev@xxxxxxxxxx>
> Signed-off-by: Stefan Agner <stefan@xxxxxxxx>
> ---
> .../bindings/mtd/nvidia-tegra20-nand.txt | 64 +++++++++++++++++++
> 1 file changed, 64 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt
>
> diff --git a/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt b/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt
> new file mode 100644
> index 000000000000..5cd984ef046b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mtd/nvidia-tegra20-nand.txt
> @@ -0,0 +1,64 @@
> +NVIDIA Tegra NAND Flash controller
> +
> +Required properties:
> +- compatible: Must be one of:
> + - "nvidia,tegra20-nand"
As discussed previously, I prefer "nvidia,tegra20-nand-controller" or
"nvidia,tegra20-nfc".
> +- reg: MMIO address range
> +- interrupts: interrupt output of the NFC controller
> +- clocks: Must contain an entry for each entry in clock-names.
> + See ../clocks/clock-bindings.txt for details.
> +- clock-names: Must include the following entries:
> + - nand
> +- resets: Must contain an entry for each entry in reset-names.
> + See ../reset/reset.txt for details.
> +- reset-names: Must include the following entries:
> + - nand
> +
> +Optional children nodes:
> +Individual NAND chips are children of the NAND controller node. Currently
> +only one NAND chip supported.
> +
> +Required children node properties:
> +- reg: An integer ranging from 1 to 6 representing the CS line to use.
> +
> +Optional children node properties:
> +- nand-ecc-mode: String, operation mode of the NAND ecc mode. Currently only
> + "hw" is supported.
> +- nand-ecc-algo: string, algorithm of NAND ECC.
> + Supported values with "hw" ECC mode are: "rs", "bch".
> +- nand-bus-width : See nand.txt
> +- nand-on-flash-bbt: See nand.txt
> +- nand-ecc-strength: integer representing the number of bits to correct
> + per ECC step (always 512). Supported strength using HW ECC
> + modes are:
> + - RS: 4, 6, 8
> + - BCH: 4, 8, 14, 16
> +- nand-ecc-maximize: See nand.txt
> +- nand-is-boot-medium: Makes sure only ECC strengths supported by the boot ROM
> + are choosen.
> +- wp-gpios: GPIO specifier for the write protect pin.
> +
> +Optional child node of NAND chip nodes:
> +Partitions: see partition.txt
> +
> + Example:
> + nand@70008000 {
nand-controller@70008000 {
> + compatible = "nvidia,tegra20-nand";
compatible = "nvidia,tegra20-nand-controller";
or
compatible = "nvidia,tegra20-nfc";
> + reg = <0x70008000 0x100>;
> + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&tegra_car TEGRA20_CLK_NDFLASH>;
> + clock-names = "nand";
> + resets = <&tegra_car 13>;
> + reset-names = "nand";
> +
> + nand-chip@0 {
nand@0 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + nand-bus-width = <8>;
> + nand-on-flash-bbt;
> + nand-ecc-algo = "bch";
> + nand-ecc-strength = <8>;
> + wp-gpios = <&gpio TEGRA_GPIO(S, 0) GPIO_ACTIVE_LOW>;
> + };
> + };
With this addressed,
Reviewed-by: Boris Brezillon <boris.brezillon@xxxxxxxxxxx>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
