Re: [PATCH 1/6] dt-bindings: media: rcar-vin: Describe optional ep properties

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Rob,

On Wednesday, 23 May 2018 19:29:47 EEST Rob Herring wrote:
> On Wed, May 16, 2018 at 06:32:27PM +0200, Jacopo Mondi wrote:
> > Describe the optional endpoint properties for endpoint nodes of port@0
> > and port@1 of the R-Car VIN driver device tree bindings documentation.
> > 
> > Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> > ---
> > 
> >  Documentation/devicetree/bindings/media/rcar_vin.txt | 13 ++++++++++++-
> >  1 file changed, 12 insertions(+), 1 deletion(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt
> > b/Documentation/devicetree/bindings/media/rcar_vin.txt index
> > a19517e1..c53ce4e 100644
> > --- a/Documentation/devicetree/bindings/media/rcar_vin.txt
> > +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt
> > @@ -53,6 +53,16 @@ from local SoC CSI-2 receivers (port1) depending on
> > SoC.
> > 
> >        from external SoC pins described in video-interfaces.txt[1].
> >        Describing more then one endpoint in port 0 is invalid. Only VIN
> >        instances that are connected to external pins should have port 0.
> > 
> > +
> > +      - Optional properties for endpoint nodes of port@0:
> > +        - hsync-active: active state of the HSYNC signal, 0/1 for
> > LOW/HIGH
> > +	  respectively. Default is active high.
> > +        - vsync-active: active state of the VSYNC signal, 0/1 for
> > LOW/HIGH
> > +	  respectively. Default is active high.
> > +
> > +	If both HSYNC and VSYNC polarities are not specified, embedded
> > +	synchronization is selected.
> 
> No need to copy-n-paste from video-interfaces.txt. Just "see
> video-interfaces.txt" for the description is fine.

I would still explicitly list the properties that apply to this binding. I 
agree that there's no need to copy & paste the description of those properties 
though.

> > +
> > 
> >      - port 1 - sub-nodes describing one or more endpoints connected to
> >      
> >        the VIN from local SoC CSI-2 receivers. The endpoint numbers must
> >        use the following schema.
> > 
> > @@ -62,6 +72,8 @@ from local SoC CSI-2 receivers (port1) depending on SoC.
> > 
> >          - Endpoint 2 - sub-node describing the endpoint connected to
> >          CSI40
> >          - Endpoint 3 - sub-node describing the endpoint connected to
> >          CSI41
> > 
> > +      Endpoint nodes of port@1 do not support any optional endpoint
> > property. +
> > 
> >  Device node example for Gen2 platforms
> >  --------------------------------------
> > 
> > @@ -112,7 +124,6 @@ Board setup example for Gen2 platforms (vin1 composite
> > video input)> 
> >                  vin1ep0: endpoint {
> >                  
> >                          remote-endpoint = <&adv7180>;
> > 
> > -                        bus-width = <8>;
> > 
> >                  };
> >          
> >          };
> >  
> >  };

-- 
Regards,

Laurent Pinchart



--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux