Now with the driver updates for some peripherals being there,
add i2c, spi, pcie, bam, qpic-nand, scm nodes to enhance the available
peripheral support.
Reviewed-by: Abhishek Sahu <absahu@xxxxxxxxxxxxxx>
Signed-off-by: Sricharan R <sricharan@xxxxxxxxxxxxxx>
---
arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi | 2 +-
arch/arm/boot/dts/qcom-ipq4019.dtsi | 156 ++++++++++++++++++++++++--
2 files changed, 146 insertions(+), 12 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
index ef8d8c8..418f9a0 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
@@ -69,7 +69,7 @@
status = "ok";
};
- spi_0: spi@78b5000 {
+ spi@78b5000 {
pinctrl-0 = <&spi_0_pins>;
pinctrl-names = "default";
status = "ok";
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index ea9202a..1541e18 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -24,8 +24,10 @@
interrupt-parent = <&intc>;
aliases {
- spi0 = &spi_0;
- i2c0 = &i2c_0;
+ spi0 = &blsp1_spi1;
+ spi1 = &blsp1_spi2;
+ i2c0 = &blsp1_i2c3;
+ i2c1 = &blsp1_i2c4;
};
cpus {
@@ -104,6 +106,12 @@
};
};
+ firmware {
+ scm {
+ compatible = "qcom,scm-ipq4019";
+ };
+ };
+
timer {
compatible = "arm,armv7-timer";
interrupts = <1 2 0xf08>,
@@ -149,13 +157,13 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
- interrupts = <0 208 0>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
};
blsp_dma: dma@7884000 {
compatible = "qcom,bam-v1.7.0";
reg = <0x07884000 0x23000>;
- interrupts = <GIC_SPI 238 IRQ_TYPE_NONE>;
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
@@ -163,7 +171,7 @@
status = "disabled";
};
- spi_0: spi@78b5000 {
+ blsp1_spi1: spi@78b5000 { /* BLSP1 QUP1 */
compatible = "qcom,spi-qup-v2.2.1";
reg = <0x78b5000 0x600>;
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
@@ -172,10 +180,26 @@
clock-names = "core", "iface";
#address-cells = <1>;
#size-cells = <0>;
+ dmas = <&blsp_dma 5>, <&blsp_dma 4>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ blsp1_spi2: spi@78b6000 { /* BLSP1 QUP2 */
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x78b6000 0x600>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&blsp_dma 7>, <&blsp_dma 6>;
+ dma-names = "rx", "tx";
status = "disabled";
};
- i2c_0: i2c@78b7000 {
+ blsp1_i2c3: i2c@78b7000 { /* BLSP1 QUP3 */
compatible = "qcom,i2c-qup-v2.2.1";
reg = <0x78b7000 0x600>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
@@ -184,14 +208,29 @@
clock-names = "iface", "core";
#address-cells = <1>;
#size-cells = <0>;
+ dmas = <&blsp_dma 9>, <&blsp_dma 8>;
+ dma-names = "rx", "tx";
status = "disabled";
};
+ blsp1_i2c4: i2c@78b8000 { /* BLSP1 QUP4 */
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x78b8000 0x600>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>,
+ <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
+ clock-names = "iface", "core";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dmas = <&blsp_dma 11>, <&blsp_dma 10>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
cryptobam: dma@8e04000 {
compatible = "qcom,bam-v1.7.0";
reg = <0x08e04000 0x20000>;
- interrupts = <GIC_SPI 207 0>;
+ interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_CRYPTO_AHB_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
@@ -259,7 +298,7 @@
blsp1_uart1: serial@78af000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x78af000 0x200>;
- interrupts = <0 107 0>;
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
@@ -271,7 +310,7 @@
serial@78b0000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x78b0000 0x200>;
- interrupts = <0 108 0>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
@@ -293,6 +332,101 @@
reg = <0x4ab000 0x4>;
};
+ pcie0: pci@40000000 {
+ compatible = "qcom,pcie-ipq4019", "snps,dw-pcie";
+ reg = <0x40000000 0xf1d
+ 0x40000f20 0xa8
+ 0x80000 0x2000
+ 0x40100000 0x1000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0 0x40200000 0x40200000 0 0x00100000
+ 0x82000000 0 0x48000000 0x48000000 0 0x10000000>;
+
+ interrupts = <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 144 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 145 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+ clocks = <&gcc GCC_PCIE_AHB_CLK>,
+ <&gcc GCC_PCIE_AXI_M_CLK>,
+ <&gcc GCC_PCIE_AXI_S_CLK>;
+ clock-names = "aux",
+ "master_bus",
+ "slave_bus";
+
+ resets = <&gcc PCIE_AXI_M_ARES>,
+ <&gcc PCIE_AXI_S_ARES>,
+ <&gcc PCIE_PIPE_ARES>,
+ <&gcc PCIE_AXI_M_VMIDMT_ARES>,
+ <&gcc PCIE_AXI_S_XPU_ARES>,
+ <&gcc PCIE_PARF_XPU_ARES>,
+ <&gcc PCIE_PHY_ARES>,
+ <&gcc PCIE_AXI_M_STICKY_ARES>,
+ <&gcc PCIE_PIPE_STICKY_ARES>,
+ <&gcc PCIE_PWR_ARES>,
+ <&gcc PCIE_AHB_ARES>,
+ <&gcc PCIE_PHY_AHB_ARES>;
+ reset-names = "axi_m",
+ "axi_s",
+ "pipe",
+ "axi_m_vmid",
+ "axi_s_xpu",
+ "parf",
+ "phy",
+ "axi_m_sticky",
+ "pipe_sticky",
+ "pwr",
+ "ahb",
+ "phy_ahb";
+
+ status = "disabled";
+ };
+
+ qpic_bam: dma@7984000 {
+ compatible = "qcom,bam-v1.7.0";
+ reg = <0x7984000 0x1a000>;
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_QPIC_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ status = "disabled";
+ };
+
+ nand: qpic-nand@79b0000 {
+ compatible = "qcom,ipq4019-nand";
+ reg = <0x79b0000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&gcc GCC_QPIC_CLK>,
+ <&gcc GCC_QPIC_AHB_CLK>;
+ clock-names = "core", "aon";
+
+ dmas = <&qpic_bam 0>,
+ <&qpic_bam 1>,
+ <&qpic_bam 2>;
+ dma-names = "tx", "rx", "cmd";
+ status = "disabled";
+
+ nand@0 {
+ reg = <0>;
+
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-bus-width = <8>;
+ };
+ };
+
wifi0: wifi@a000000 {
compatible = "qcom,ipq4019-wifi";
reg = <0xa000000 0x200000>;
@@ -326,7 +460,7 @@
<GIC_SPI 45 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 46 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 47 IRQ_TYPE_EDGE_RISING>,
- <GIC_SPI 168 IRQ_TYPE_NONE>;
+ <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi0", "msi1", "msi2", "msi3",
"msi4", "msi5", "msi6", "msi7",
"msi8", "msi9", "msi10", "msi11",
@@ -368,7 +502,7 @@
<GIC_SPI 61 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 62 IRQ_TYPE_EDGE_RISING>,
<GIC_SPI 63 IRQ_TYPE_EDGE_RISING>,
- <GIC_SPI 169 IRQ_TYPE_NONE>;
+ <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi0", "msi1", "msi2", "msi3",
"msi4", "msi5", "msi6", "msi7",
"msi8", "msi9", "msi10", "msi11",
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
