The Raspberry Pi Compute Module (CM1) is a SoM which contains a
BCM2835 processor, 512 MB RAM and a 4 GB eMMC. There is also a carrier
board which is called Compute Module IO Board.
Signed-off-by: Stefan Wahren <stefan.wahren@xxxxxxxx>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts | 92 +++++++++++++++++++++++++++++++
arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi | 34 ++++++++++++
3 files changed, 127 insertions(+)
create mode 100644 arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts
create mode 100644 arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ec2024e..a9883e8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -73,6 +73,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
bcm2835-rpi-b-rev2.dtb \
bcm2835-rpi-b-plus.dtb \
bcm2835-rpi-a-plus.dtb \
+ bcm2835-rpi-cm1-io1.dtb \
bcm2836-rpi-2-b.dtb \
bcm2837-rpi-3-b.dtb \
bcm2837-rpi-3-b-plus.dtb \
diff --git a/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts b/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts
new file mode 100644
index 0000000..4d9aa22
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts
@@ -0,0 +1,92 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835-rpi-cm1.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+ model = "Raspberry Pi Compute Module IO board rev1";
+};
+
+&dsi1 {
+ status = "okay";
+};
+
+&gpio {
+ /*
+ * This is based on the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "GPIO0",
+ "GPIO1",
+ "GPIO2",
+ "GPIO3",
+ "GPIO4",
+ "GPIO5",
+ "GPIO6",
+ "GPIO7",
+ "GPIO8",
+ "GPIO9",
+ "GPIO10",
+ "GPIO11",
+ "GPIO12",
+ "GPIO13",
+ "GPIO14",
+ "GPIO15",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "GPIO28",
+ "GPIO29",
+ "GPIO30",
+ "GPIO31",
+ "GPIO32",
+ "GPIO33",
+ "GPIO34",
+ "GPIO35",
+ "GPIO36",
+ "GPIO37",
+ "GPIO38",
+ "GPIO39",
+ "GPIO40",
+ "GPIO41",
+ "GPIO42",
+ "GPIO43",
+ "GPIO44",
+ "GPIO45",
+ "HDMI_HPD_N",
+ /* Also used as ACT LED */
+ "EMMC_EN_N",
+ /* Used by eMMC */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi b/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi
new file mode 100644
index 0000000..ef22c2d
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+
+/ {
+ leds {
+ act {
+ gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ reg_3v3: fixed-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_1v8: fixed-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+};
+
+&sdhost {
+ non-removable;
+ vmmc-supply = <®_3v3>;
+ vqmmc-supply = <®_1v8>;
+};
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
