It adds combophy devices under peripheral controller and enables PCIe
support for Hi3798CV200 Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@xxxxxxxxxx>
---
.../boot/dts/hisilicon/hi3798cv200-poplar.dts | 15 ++++++
arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi | 63 ++++++++++++++++++++++
2 files changed, 78 insertions(+)
diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
index 4d5d644abb12..c4382e1f3c92 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
@@ -61,6 +61,15 @@
default-state = "off";
};
};
+
+ reg_pcie: regulator-pcie {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3_PCIE0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio6 7 0>;
+ enable-active-high;
+ };
};
&gmac1 {
@@ -146,6 +155,12 @@
status = "okay";
};
+&pcie {
+ reset-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
+ vpcie-supply = <®_pcie>;
+ status = "okay";
+};
+
&sd0 {
bus-width = <4>;
cap-sd-highspeed;
diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
index 962bd79139e4..5b73403551e6 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
@@ -8,7 +8,9 @@
*/
#include <dt-bindings/clock/histb-clock.h>
+#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy.h>
#include <dt-bindings/reset/ti-syscon.h>
/ {
@@ -106,6 +108,37 @@
#reset-cells = <2>;
};
+ perictrl: peripheral-controller@8a20000 {
+ compatible = "hisilicon,hi3798cv200-perictrl", "syscon",
+ "simple-mfd";
+ reg = <0x8a20000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x8a20000 0x1000>;
+
+ combphy0: phy@850 {
+ compatible = "hisilicon,hi3798cv200-combphy";
+ reg = <0x850 0x8>;
+ #phy-cells = <1>;
+ clocks = <&crg HISTB_COMBPHY0_CLK>;
+ resets = <&crg 0x188 4>;
+ assigned-clocks = <&crg HISTB_COMBPHY0_CLK>;
+ assigned-clock-rates = <100000000>;
+ hisilicon,fixed-mode = <PHY_TYPE_USB3>;
+ };
+
+ combphy1: phy@858 {
+ compatible = "hisilicon,hi3798cv200-combphy";
+ reg = <0x858 0x8>;
+ #phy-cells = <1>;
+ clocks = <&crg HISTB_COMBPHY1_CLK>;
+ resets = <&crg 0x188 12>;
+ assigned-clocks = <&crg HISTB_COMBPHY1_CLK>;
+ assigned-clock-rates = <100000000>;
+ hisilicon,mode-select-bits = <0x0008 11 (0x3 << 11)>;
+ };
+ };
+
uart0: serial@8b00000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x8b00000 0x1000>;
@@ -419,5 +452,35 @@
clocks = <&sysctrl HISTB_IR_CLK>;
status = "disabled";
};
+
+ pcie: pcie@9860000 {
+ compatible = "hisilicon,hi3798cv200-pcie";
+ reg = <0x9860000 0x1000>,
+ <0x0 0x2000>,
+ <0x2000000 0x01000000>;
+ reg-names = "control", "rc-dbi", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ bus-range = <0 15>;
+ num-lanes = <1>;
+ ranges = <0x81000000 0x0 0x00000000 0x4f00000 0x0 0x100000
+ 0x82000000 0x0 0x3000000 0x3000000 0x0 0x01f00000>;
+ interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic 0 131 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&crg HISTB_PCIE_AUX_CLK>,
+ <&crg HISTB_PCIE_PIPE_CLK>,
+ <&crg HISTB_PCIE_SYS_CLK>,
+ <&crg HISTB_PCIE_BUS_CLK>;
+ clock-names = "aux", "pipe", "sys", "bus";
+ resets = <&crg 0x18c 6>, <&crg 0x18c 5>, <&crg 0x18c 4>;
+ reset-names = "soft", "sys", "bus";
+ phys = <&combphy1 PHY_TYPE_PCIE>;
+ phy-names = "phy";
+ status = "disabled";
+ };
};
};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
