On 05/08/2018 12:34 AM, Bjorn Andersson wrote:
On Mon 07 May 12:55 PDT 2018, Rob Herring wrote:
On Mon, May 7, 2018 at 1:31 PM, Bjorn Andersson
<bjorn.andersson@xxxxxxxxxx> wrote:
On Tue 01 May 14:31 PDT 2018, Rob Herring wrote:
Deferred probe will currently wait forever on dependent devices to probe,
but sometimes a driver will never exist. It's also not always critical for
a driver to exist. Platforms can rely on default configuration from the
bootloader or reset defaults for things such as pinctrl and power domains.
But how do you know if this is the case?
Because the platform worked before adding the dependency in the dts.
I'm worried about how to write dts files and drivers to support all
permutation of forward and backward dependencies. And you most
definitely have the same case with bootloader-enabled clocks,
regulators and interconnects.
This is often the case with initial platform support until various drivers
get enabled.
Can you please name platform that has enough support for Alexander to
care about backwards and forwards compatibility but lacks a pinctrl
driver.
Alex will have to answer that. I do agree pinctrl drivers shouldn't be
that hard because it is all just translating a bunch of pin data into
one-time (mostly) register writes, so it shouldn't take that long to
implement support. OTOH, maybe a pinctrl driver is low priority
because nothing needs it yet. Either a given board works with the
defaults and only some new board needs to change things or you don't
need pinctrl until low power modes are implemented. However, power
domains have the same problem and it can take years for those to get
proper support.
Alex proposed declaring dts files stable and then enforcing
compatibility after that point. If anyone believes that will work,
then please send a patch marking all the platforms in the kernel tree
that are stable.
That might be a reasonable idea, but at least in our corner the current
decision that devicetree should be backwards compatible does make it
quite cumbersome to break this assumption - and in the cases we have had
to do it it's really been necessary.
I'm sure Rob would be happy to get a list of every one of those
instances so we can see how to solve them going forward.
To give you some background: The whole discussion started with a
proposal from me to support embedded (maybe dtc aided) overlays. Some
way to have a single dtb that only enables new features such as pinctrl
when the kernel indicates support for them.
I think eventually we will have to have a mechanism like that for
platforms that want to maintain compatibility. But the less we have to
solve using it the better off everyone is, because it just increases
complexity.
There's at least 2 scenarios where deferred probe can render
a platform broken. Both involve using a DT which has more devices and
dependencies than the kernel supports. The 1st case is a driver may be
disabled in the kernel config.
I agree that there is a chance that you _might_ get some parts of the
system working by relying on the boot loader configuration, but
misconfiguration issues applies to any other fundamental providers, such
as clocks, regulators, power domains and gpios as well.
If it is only a chance, then perhaps we shouldn't allow things
upstream without proper drivers for all these things. That will only
give users the wrong impression.
It's not as much the drivers that's the problem here as it is the
composition of the drivers. For this particular case it would be
convenient not to ship the partial dtb, or at least not ship it with the
promise that it's stable.
Yes, we of course need a gatekeeping event. Not every DT is in a state
where you can promise compatibility.
However, if you want to have a stable OS interface so that slow moving
Linux distribtions work well with the platform and non-Linux OSs jump on
the platform, you will have to provide some guarantees. And people just
need to be aware that they either give the guarantees or they don't get
their benefits :).
The 2nd case is the kernel version may
simply not have the dependent driver. This can happen if using a newer DT
(provided by firmware perhaps) with a stable kernel version.
As above, this is in no way limited to pinctrl drivers.
Yes, I wasn't trying to imply that with this patch. I was just
starting with 1 example. IOMMUs (which essentially is already doing
what this patch does) and power domains are the main other 2.
qcom,iommu-v1 is bool, but depends on e.g. CONFIG_MSM_GCC_8916 which is
tristate. So you would need to s/tristate/bool/ everything in
drivers/clk/qcom/Kconfig as well. Not to mention that there are
interconnects and power domains actually involved here as well...
Clocks is an obvious one too, but from the discussion I referenced
that problem is a bit different as platforms change from dummy
fixed-clocks to a real clock controller driver. That will need a
different solution.
So how are you going to deal with the case when a vendor decides to ship
their firmware package with all clocks enabled and only fixed clocks
described in DT and as they upstream a clock driver and patch their
firmware to do the right thing?
That is the ZynqMP case. I think this really needs to be solved using
embedded overlays, but Rob might have additional ideas :).
(Or the much less extreme case where this happens for a single clock,
regulator, pinctrl, interconnect, etc to fix some bug/power management
behavior)
And is this really a problem that does not exists in the ACPI world?
Unfortunately, this change breaks with modules as we have no way of
knowing when modules are done loading. One possibility is to make this
opt in or out based on compatible strings rather than at a subsystem level.
Ideally this information could be extracted automatically somehow. OTOH,
maybe the lists are pretty small. There's only a handful of subsystems
that can be optional, and then only so many drivers in those that can be
modules (at least for pinctrl, many drivers are built-in only).
On the Qualcomm platform most drivers are tristate and on most platforms
there are size restrictions in the proprietary boot loader preventing us
from boot the kernel after switching all these frameworks from tristate
to bool (which feels like a more appropriate solution than your hack).
BTW, QCom platforms are almost the only ones with pinctrl drivers as
modules. They are also happen to be PIA to configure correctly for a
board.
There are a few pinctrl drivers for chips sitting on i2c busses, as such
changing this requirement would trickle down to a number of possible i2c
masters as well.
Sorry to hear that you find it so difficult to configure the pinctrl,
it's (almost) entirely using the common pinctrl bindings. Perhaps we
need to add some documentation of the hardware in the binding?
However, I would like a solution that works with modules. It would be
nice to know when userspace finished processing all the coldplug
uevents. That would be sufficient to support modules. I researched
that a bit and it doesn't seem the kernel can tell when that has
happened.
It's not that far from the issue I have in remoteproc, where I would
like to boot a DSP as soon as the firmware is available - which might be
probed at any time after boot.
[..]
I tested this on a RPi3 B with the pinctrl driver forced off. With this
change, the MMC/SD and UART drivers can function without the pinctrl
driver.
Cool, so what about graphics, audio, networking, usb and all the other
things that people actually expect when they _use_ a distro?
I often care about none of those things. When I do, I'd rather boot to
a working console with those broken than have to debug why the kernel
panicked.
But that's developer-you speaking, developer-me totally agree.
But when I take the role of being a user of a distro I most definitely
do expect functionality beyond the basics used by the boot loader (UART
and dependencies of the primary storage device).
My argument is simply that in neither of these cases this patch is
helpful.
The patch allows firmware to provide pinctrl information but maintain
backwards compatibility with kernels that don't implement pinctrl
setting. It's useful to solve that part of the transition of the DT to
enable new functionality. If you now add a device that explicitly needs
pinctrl configuration to work, that would probably need to get added
using the overlay mechanism I described above.
Alex
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
