On 04/16/2018 08:19 PM, Rob Herring wrote:
> On Wed, Apr 11, 2018 at 11:47:01AM +0200, Amelie Delaunay wrote:
>> This patch adds documentation of device tree bindings for the
>> STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander.
>>
>> Signed-off-by: Amelie Delaunay <amelie.delaunay@xxxxxx>
>> ---
>> .../devicetree/bindings/pinctrl/pinctrl-stmfx.txt | 118 +++++++++++++++++++++
>> 1 file changed, 118 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt
>> new file mode 100644
>> index 0000000..4d8941de
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt
>> @@ -0,0 +1,118 @@
>> +STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander bindings
>> +
>> +ST Multi-Function eXpander (STMFX) is a slave controller using I2C for
>> +communication with the main MCU. It offers up to 24 GPIOs expansion.
>> +
>> +Required properties:
>> +- compatible: should be "st,stmfx-0300".
>> +- reg: I2C slave address of the device.
>> +- interrupt-parent: phandle of the STMFX parent interrupt controller.
>> +- interrutps: interrupt specifier triggered by MFX_IRQ_OUT signal.
>> +
>> +Optional property:
>
> s/property/properties/
>
>> +- drive-open-drain: configure MFX_IRQ_OUT as open drain.
>> +- vdd-supply: phandle of the regulator supplying STMFX.
>> +
>> +Required properties for gpio controller sub-node:
>> +- #gpio-cells: should be <2>, the first cell is the GPIO number and the second
>> + cell is the gpio flags in accordance with <dt-bindings/gpio/gpio.h>.
>> +- gpio-controller: marks the device as a GPIO controller.
>> +Please refer to ../gpio/gpio.txt.
>> +
>> +Optional properties for gpio controller sub-node:
>> +- #interrupt-cells: should be <2>, the first cell is the GPIO number and the
>> + second cell is the interrupt flags in accordance with
>> + <dt-bindings/interrupt-controller/irq.h>.
>> +- interrupt-controller: marks the device as an interrupt controller.
>> +
>> +Please refer to pinctrl-bindings.txt for pin configuration.
>> +
>> +Required properties for pin configuration sub-nodes:
>> +- pins: list of pins to which the configuration applies.
>> +
>> +Optional properties for pin configuration sub-nodes (pinconf-generic ones):
>> +- bias-disable: disable any bias on the pin.
>> +- bias-pull-up: the pin will be pulled up.
>> +- bias-pull-pin-default: use the pin-default pull state.
>> +- bias-pull-down: the pin will be pulled down.
>> +- drive-open-drain: the pin will be driven with open drain.
>> +- drive-push-pull: the pin will be driven actively high and low.
>> +- output-high: the pin will be configured as an output driving high level.
>> +- output-low: the pin will be configured as an output driving low level.
>> +
>> +Note that STMFX pins[15:0] are called "gpio[15:0]", and STMFX pins[23:16] are
>> +called "agpio[7:0]". Example, to refer to pin 18 of STMFX, use "agpio2".
>> +
>> +Example:
>> +
>> + stmfxpinctrl: stmfx@42 {
>> + compatible = "st,stmfx-0300";
>> + reg = <0x42>;
>> + interrupt-parent = <&gpioi>;
>> + interrupts = <8 IRQ_TYPE_EDGE_RISING>;
>> + vdd-supply = <&v3v3>;
>> + status = "okay";
>
> Don't show status in examples.
>
I'll fix it.
>> +
>> + stmfxgpio: gpio {
>
> Why does this need to be a sub node? Are there functions beyond GPIO?
>
I'll address this point in my response to Linus.
>> + #gpio-cells = <2>;
>> + #interrupt-cells = <2>;
>> + gpio-controller;
>> + interrupt-controller;
>> + status = "okay";
>> + };
>> +
>> + joystick_pins: joystick@0 {
>
> A unit-address without a reg prop is not valid.
>
OK, I'll replace it by 'joystick_pins: joystick-0'.
>> + pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
>> + drive-push-pull;
>> + bias-pull-down;
>> + };
>> + };
>> +
>> + joystick {
>> + compatible = "gpio-keys";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + pinctrl-0 = <&joystick_pins>;
>> + pinctrl-names = "default";
>> + button@0 {
>> + label = "JoySel";
>> + linux,code = <KEY_ENTER>;
>> + interrupt-parent = <&stmfxgpio>;
>> + interrupts = <0 IRQ_TYPE_EDGE_RISING>;
>> + };
>> + button@1 {
>> + label = "JoyDown";
>> + linux,code = <KEY_DOWN>;
>> + interrupt-parent = <&stmfxgpio>;
>> + interrupts = <1 IRQ_TYPE_EDGE_RISING>;
>> + };
>> + button@2 {
>> + label = "JoyLeft";
>> + linux,code = <KEY_LEFT>;
>> + interrupt-parent = <&stmfxgpio>;
>> + interrupts = <2 IRQ_TYPE_EDGE_RISING>;
>> + };
>> + button@3 {
>> + label = "JoyRight";
>> + linux,code = <KEY_RIGHT>;
>> + interrupt-parent = <&stmfxgpio>;
>> + interrupts = <3 IRQ_TYPE_EDGE_RISING>;
>> + };
>> + button@4 {
>> + label = "JoyUp";
>> + linux,code = <KEY_UP>;
>> + interrupt-parent = <&stmfxgpio>;
>> + interrupts = <4 IRQ_TYPE_EDGE_RISING>;
>> + };
>> + };
>> +
>> + leds {
>> + compatible = "gpio-leds";
>> + orange {
>> + gpios = <&stmfxgpio 17 1>;
>> + };
>> +
>> + blue {
>> + gpios = <&stmfxgpio 19 1>;
>> + };
>> + }
>> --
>> 2.7.4
>>
Thanks,
Amelie��.n��������+%������w��{.n����z�{��ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f
