From: Hari Nagalla <hnagalla@xxxxxx>
The wilink module is a combo wireless connectivity sdio
card based on Texas Instrument's wl18xx solution. It is a
4-wire, 1.8V, embedded sdio wlan device with an external
irq line and is power-controlled by a gpio-based fixed
regulator.
Add pinmux configuration and IODelay values for MMC4.
On dra7-evm, MMC4 is used for connecting to wilink module.
IODelay data credits to : Vishal Mahaveer <vishalm@xxxxxx>
and Sekhar Nori <nsekhar@xxxxxx>
Signed-off-by: Ido Yariv <ido@xxxxxxxxxx>
Signed-off-by: Eyal Reizer <eyalr@xxxxxx>
Signed-off-by: Hari Nagalla <hnagalla@xxxxxx>
Signed-off-by: Sekhar Nori <nsekhar@xxxxxx>
Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx>
---
arch/arm/boot/dts/dra7-evm-common.dtsi | 15 +++++++++++++++
arch/arm/boot/dts/dra7-evm.dts | 25 +++++++++++++++++++++++++
2 files changed, 40 insertions(+)
diff --git a/arch/arm/boot/dts/dra7-evm-common.dtsi b/arch/arm/boot/dts/dra7-evm-common.dtsi
index 05a7b1a01bc3..3590c40fc112 100644
--- a/arch/arm/boot/dts/dra7-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra7-evm-common.dtsi
@@ -260,3 +260,18 @@
&pcie1_rc {
status = "okay";
};
+
+&mmc4 {
+ bus-width = <4>;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ non-removable;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <7 IRQ_TYPE_EDGE_RISING>;
+ };
+};
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index 181289a28ca1..704947cbef48 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -96,6 +96,16 @@
regulator-boot-on;
};
+ vmmcwl_fixed: fixedregulator-mmcwl {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcwl_fixed";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&gpio5 8 0>;
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
extcon_usb2: extcon_usb2 {
compatible = "linux,extcon-usb-gpio";
id-gpio = <&pcf_gpio_21 2 GPIO_ACTIVE_HIGH>;
@@ -376,6 +386,21 @@
pinctrl-5 = <&mmc2_pins_hs200 &mmc2_iodelay_hs200_rev20_conf>;
};
+&mmc4 {
+ status = "okay";
+ vmmc-supply = <&evm_3v6>;
+ vqmmc-supply = <&vmmcwl_fixed>;
+ pinctrl-names = "default-rev11", "default", "hs-rev11", "hs", "sdr12-rev11", "sdr12", "sdr25-rev11", "sdr25";
+ pinctrl-0 = <&mmc4_pins_default &mmc4_iodelay_ds_rev11_conf>;
+ pinctrl-1 = <&mmc4_pins_default &mmc4_iodelay_ds_rev20_conf>;
+ pinctrl-2 = <&mmc4_pins_hs &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>;
+ pinctrl-3 = <&mmc4_pins_hs &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>;
+ pinctrl-4 = <&mmc4_pins_sdr12 &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>;
+ pinctrl-5 = <&mmc4_pins_sdr12 &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>;
+ pinctrl-6 = <&mmc4_pins_sdr25 &mmc4_iodelay_sdr12_hs_sdr25_rev11_conf>;
+ pinctrl-7 = <&mmc4_pins_sdr25 &mmc4_iodelay_sdr12_hs_sdr25_rev20_conf>;
+};
+
&cpu0 {
vdd-supply = <&smps123_reg>;
};
--
2.17.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
