Hi,
On Wed, Apr 04, 2018 at 01:30:37PM -0500, Dan Murphy wrote:
> Sebastian
>
> -Milo Kim email is not valid
Thanks for your review! Milo was CC'd, since git took over the
SoB. I will make sure to avoid it next time.
> On 03/30/2018 12:24 PM, Sebastian Reichel wrote:
> > This adds backlight support for the following TI LMU
> > chips: LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
> >
> > Signed-off-by: Milo Kim <milo.kim@xxxxxx>
> > [add LED subsystem support for keyboard backlight and rework DT
> > binding according to Rob Herrings feedback]
> > Signed-off-by: Sebastian Reichel <sebastian.reichel@xxxxxxxxxxxxxxx>
> > ---
> > drivers/video/backlight/Kconfig | 7 +
> > drivers/video/backlight/Makefile | 3 +
> > drivers/video/backlight/ti-lmu-backlight-core.c | 666 ++++++++++++++++++++++++
> > drivers/video/backlight/ti-lmu-backlight-data.c | 304 +++++++++++
> > drivers/video/backlight/ti-lmu-backlight-data.h | 95 ++++
> > 5 files changed, 1075 insertions(+)
> > create mode 100644 drivers/video/backlight/ti-lmu-backlight-core.c
> > create mode 100644 drivers/video/backlight/ti-lmu-backlight-data.c
> > create mode 100644 drivers/video/backlight/ti-lmu-backlight-data.h
> >
> > diff --git a/drivers/video/backlight/Kconfig b/drivers/video/backlight/Kconfig
> > index 5d2d0d7e8100..27e6c5a0add8 100644
> > --- a/drivers/video/backlight/Kconfig
> > +++ b/drivers/video/backlight/Kconfig
> > @@ -427,6 +427,13 @@ config BACKLIGHT_SKY81452
> > To compile this driver as a module, choose M here: the module will
> > be called sky81452-backlight
> >
> > +config BACKLIGHT_TI_LMU
> > + tristate "Backlight driver for TI LMU"
> > + depends on BACKLIGHT_CLASS_DEVICE && MFD_TI_LMU
>
> select REGMAP?
Right.
> > + help
> > + Say Y to enable the backlight driver for TI LMU devices.
> > + This supports LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
> > +
> > config BACKLIGHT_TPS65217
> > tristate "TPS65217 Backlight"
> > depends on BACKLIGHT_CLASS_DEVICE && MFD_TPS65217
> > diff --git a/drivers/video/backlight/Makefile b/drivers/video/backlight/Makefile
> > index 19da71d518bf..a1132d3dfd4c 100644
> > --- a/drivers/video/backlight/Makefile
> > +++ b/drivers/video/backlight/Makefile
> > @@ -53,6 +53,9 @@ obj-$(CONFIG_BACKLIGHT_PM8941_WLED) += pm8941-wled.o
> > obj-$(CONFIG_BACKLIGHT_PWM) += pwm_bl.o
> > obj-$(CONFIG_BACKLIGHT_SAHARA) += kb3886_bl.o
> > obj-$(CONFIG_BACKLIGHT_SKY81452) += sky81452-backlight.o
> > +ti-lmu-backlight-objs := ti-lmu-backlight-core.o \
> > + ti-lmu-backlight-data.o
> > +obj-$(CONFIG_BACKLIGHT_TI_LMU) += ti-lmu-backlight.o
> > obj-$(CONFIG_BACKLIGHT_TOSA) += tosa_bl.o
> > obj-$(CONFIG_BACKLIGHT_TPS65217) += tps65217_bl.o
> > obj-$(CONFIG_BACKLIGHT_WM831X) += wm831x_bl.o
> > diff --git a/drivers/video/backlight/ti-lmu-backlight-core.c b/drivers/video/backlight/ti-lmu-backlight-core.c
> > new file mode 100644
> > index 000000000000..a6099581edd7
> > --- /dev/null
> > +++ b/drivers/video/backlight/ti-lmu-backlight-core.c
> > @@ -0,0 +1,666 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright 2015 Texas Instruments
> > + * Copyright 2018 Sebastian Reichel
> > + *
> > + * TI LMU Backlight driver, based on previous work from
> > + * Milo Kim <milo.kim@xxxxxx>
> > + */
> > +
> > +#include <linux/backlight.h>
> > +#include <linux/bitops.h>
> > +#include <linux/device.h>
> > +#include <linux/delay.h>
> > +#include <linux/err.h>
> > +#include <linux/leds.h>
> > +#include <linux/mfd/ti-lmu.h>
> > +#include <linux/mfd/ti-lmu-register.h>
> > +#include <linux/module.h>
> > +#include <linux/notifier.h>
> > +#include <linux/of_device.h>
> > +#include <linux/platform_device.h>
> > +
> > +#include "ti-lmu-backlight-data.h"
> > +
> > +enum ti_lmu_bl_ctrl_mode {
> > + BL_REGISTER_BASED,
> > + BL_PWM_BASED,
> > +};
> > +
> > +enum ti_lmu_bl_type {
> > + TI_LMU_BL, /* backlight userspace interface */
> > + TI_LMU_LED, /* led userspace interface */
> > +};
> > +
> > +enum ti_lmu_bl_ramp_mode {
> > + BL_RAMP_UP,
> > + BL_RAMP_DOWN,
> > +};
> > +
> > +#define DEFAULT_PWM_NAME "lmu-backlight"
>
> I don't see this used.
I guess I can remove this :)
> > +#define NUM_DUAL_CHANNEL 2
> > +#define LMU_BACKLIGHT_DUAL_CHANNEL_USED (BIT(0) | BIT(1))
> > +#define LMU_BACKLIGHT_11BIT_LSB_MASK (BIT(0) | BIT(1) | BIT(2))
> > +#define LMU_BACKLIGHT_11BIT_MSB_SHIFT 3
> > +
>
> Struct kerneldoc?
Ok.
> > +struct ti_lmu_bank {
> > + struct device *dev;
> > + int bank_id;
> > + const struct ti_lmu_bl_cfg *cfg;
> > + struct ti_lmu *lmu;
> > + const char *label;
> > + int leds;
> > + int current_brightness;
> > + u32 default_brightness;
> > + u32 ramp_up_msec;
> > + u32 ramp_down_msec;
> > + u32 pwm_period;
> > + enum ti_lmu_bl_ctrl_mode mode;
> > + enum ti_lmu_bl_type type;
> > +
> > + struct notifier_block nb;
> > +
> > + struct backlight_device *backlight;
> > + struct led_classdev *led;
> > +};
> > +
> > +static int ti_lmu_bl_enable(struct ti_lmu_bank *lmu_bank, bool enable)
> > +{
> > + struct regmap *regmap = lmu_bank->lmu->regmap;
> > + unsigned long enable_time = lmu_bank->cfg->reginfo->enable_usec;
> > + u8 *reg = lmu_bank->cfg->reginfo->enable;
> > + u8 mask = BIT(lmu_bank->bank_id);
> > + u8 val = (enable == true) ? mask : 0;
> > + int ret;
> > +
> > + if (!reg)
> > + return -EINVAL;
> > +
> > + ret = regmap_update_bits(regmap, *reg, mask, val);
> > + if (ret)
> > + return ret;
> > +
> > + if (enable_time > 0)
> > + usleep_range(enable_time, enable_time + 100);
> > +
> > + return 0;
> > +}
> > +
> > +static int ti_lmu_bl_update_brightness_register(struct ti_lmu_bank *lmu_bank,
> > + int brightness)
> > +{
> > + const struct ti_lmu_bl_cfg *cfg = lmu_bank->cfg;
> > + const struct ti_lmu_bl_reg *reginfo = cfg->reginfo;
> > + struct regmap *regmap = lmu_bank->lmu->regmap;
> > + u8 reg, val;
> > + int ret;
> > +
> > + /*
> > + * Brightness register update
> > + *
> > + * 11 bit dimming: update LSB bits and write MSB byte.
> > + * MSB brightness should be shifted.
> > + * 8 bit dimming: write MSB byte.
> > + */
> > + if (cfg->max_brightness == MAX_BRIGHTNESS_11BIT) {
> > + reg = reginfo->brightness_lsb[lmu_bank->bank_id];
> > + ret = regmap_update_bits(regmap, reg,
> > + LMU_BACKLIGHT_11BIT_LSB_MASK,
> > + brightness);
> > + if (ret)
> > + return ret;
> > +
> > + val = brightness >> LMU_BACKLIGHT_11BIT_MSB_SHIFT;
> > + } else {
> > + val = brightness;
> > + }
> > +
> > + reg = reginfo->brightness_msb[lmu_bank->bank_id];
> > + return regmap_write(regmap, reg, val);
> > +}
> > +
> > +static int ti_lmu_bl_pwm_ctrl(struct ti_lmu_bank *lmu_bank, int brightness)
> > +{
> > + int max_brightness = lmu_bank->cfg->max_brightness;
> > + struct pwm_state state = { };
> > + int ret;
> > +
> > + if (!lmu_bank->lmu->pwm) {
> > + dev_err(lmu_bank->dev, "Missing PWM device!\n");
> > + return -ENODEV;
> > + }
> > +
> > + pwm_init_state(lmu_bank->lmu->pwm, &state);
> > + state.period = lmu_bank->pwm_period;
> > + state.duty_cycle = brightness * state.period / max_brightness;
> > +
> > + if (state.duty_cycle)
> > + state.enabled = true;
> > + else
> > + state.enabled = false;
> > +
> > + ret = pwm_apply_state(lmu_bank->lmu->pwm, &state);
> > + if (ret)
> > + dev_err(lmu_bank->dev, "Failed to configure PWM: %d", ret);
> > +
> > + return ret;
> > +}
> > +
> > +static int ti_lmu_bl_set_brightness(struct ti_lmu_bank *lmu_bank,
> > + int brightness)
> > +{
> > + const struct ti_lmu_bl_cfg *cfg = lmu_bank->cfg;
> > + bool enable = brightness > 0;
> > + int ret;
> > +
>
> Is there anyway that update_status and set_led_blocking can be
> called at the same time causing a race condition in this api?
Each bank is either exclusively exposed via LED or via backlight
subsystem.
> > + ret = ti_lmu_bl_enable(lmu_bank, enable);
> > + if (ret)
> > + return ret;
> > +
> > + if (lmu_bank->mode == BL_PWM_BASED) {
> > + ti_lmu_bl_pwm_ctrl(lmu_bank, brightness);
> > +
> > + switch (cfg->pwm_action) {
> > + case UPDATE_PWM_ONLY:
> > + /* No register update is required */
> > + return 0;
> > + case UPDATE_MAX_BRT:
> > + /*
> > + * PWM can start from any non-zero code and dim down
> > + * to zero. So, brightness register should be updated
> > + * even in PWM mode.
> > + */
> > + if (brightness > 0)
> > + brightness = MAX_BRIGHTNESS_11BIT;
> > + else
> > + brightness = 0;
> > + break;
> > + default:
> > + break;
> > + }
> > + }
> > +
> > + lmu_bank->current_brightness = brightness;
> > +
> > + return ti_lmu_bl_update_brightness_register(lmu_bank, brightness);
> > +}
> > +
> > +static int ti_lmu_bl_update_status(struct backlight_device *bl_dev)
> > +{
> > + struct ti_lmu_bank *lmu_bank = bl_get_data(bl_dev);
> > + int brightness = bl_dev->props.brightness;
> > +
> > + if (bl_dev->props.state & BL_CORE_SUSPENDED)
> > + brightness = 0;
> > +
> > + return ti_lmu_bl_set_brightness(lmu_bank, brightness);
> > +}
> > +
> > +static const struct backlight_ops lmu_backlight_ops = {
> > + .options = BL_CORE_SUSPENDRESUME,
> > + .update_status = ti_lmu_bl_update_status,
> > +};
> > +
> > +static int ti_lmu_bl_set_led_blocking(struct led_classdev *ledc,
> > + enum led_brightness value)
> > +{
> > + struct ti_lmu_bank *lmu_bank = dev_get_drvdata(ledc->dev->parent);
> > + int brightness = value;
> > +
> > + return ti_lmu_bl_set_brightness(lmu_bank, brightness);
> > +}
> > +
> > +static int ti_lmu_bl_check_channel(struct ti_lmu_bank *lmu_bank)
> > +{
> > + const struct ti_lmu_bl_cfg *cfg = lmu_bank->cfg;
> > + const struct ti_lmu_bl_reg *reginfo = cfg->reginfo;
> > +
> > + if (!reginfo->brightness_msb)
> > + return -EINVAL;
> > +
> > + if (cfg->max_brightness > MAX_BRIGHTNESS_8BIT) {
> > + if (!reginfo->brightness_lsb)
> > + return -EINVAL;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ti_lmu_bl_create_channel(struct ti_lmu_bank *lmu_bank)
> > +{
> > + struct regmap *regmap = lmu_bank->lmu->regmap;
> > + const struct lmu_bl_reg_data *regdata = lmu_bank->cfg->reginfo->channel;
> > + int num_channels = lmu_bank->cfg->num_channels;
> > + unsigned long led_sources = lmu_bank->leds;
> > + int i, ret;
> > + u8 shift;
> > +
> > + /*
> > + * How to create backlight output channels:
> > + * Check 'led_sources' bit and update registers.
> > + *
> > + * 1) Dual channel configuration
> > + * The 1st register data is used for single channel.
> > + * The 2nd register data is used for dual channel.
> > + *
> > + * 2) Multiple channel configuration
> > + * Each register data is mapped to bank ID.
> > + * Bit shift operation is defined in channel registers.
> > + *
> > + * Channel register data consists of address, mask, value.
> > + */
> > +
> > + if (num_channels == NUM_DUAL_CHANNEL) {
> > + if (led_sources == LMU_BACKLIGHT_DUAL_CHANNEL_USED)
> > + regdata++;
> > +
> > + return regmap_update_bits(regmap, regdata->reg, regdata->mask,
> > + regdata->val);
> > + }
> > +
> > + for (i = 0; regdata && i < num_channels; i++) {
> > + /*
> > + * Note that the result of regdata->val is shift bit.
> > + * The bank_id should be shifted for the channel configuration.
> > + */
> > + if (test_bit(i, &led_sources)) {
> > + shift = regdata->val;
> > + ret = regmap_update_bits(regmap, regdata->reg,
> > + regdata->mask,
> > + lmu_bank->bank_id << shift);
> > + if (ret)
> > + return ret;
> > + }
> > +
> > + regdata++;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ti_lmu_bl_update_ctrl_mode(struct ti_lmu_bank *lmu_bank)
> > +{
> > + struct regmap *regmap = lmu_bank->lmu->regmap;
> > + const struct lmu_bl_reg_data *regdata =
> > + lmu_bank->cfg->reginfo->mode + lmu_bank->bank_id;
> > + u8 val = regdata->val;
> > +
> > + if (!regdata)
> > + return 0;
> > +
> > + /*
> > + * Update PWM configuration register.
> > + * If the mode is register based, then clear the bit.
> > + */
> > + if (lmu_bank->mode != BL_PWM_BASED)
> > + val = 0;
> > +
> > + return regmap_update_bits(regmap, regdata->reg, regdata->mask, val);
> > +}
> > +
> > +static int ti_lmu_bl_convert_ramp_to_index(struct ti_lmu_bank *lmu_bank,
> > + enum ti_lmu_bl_ramp_mode mode)
> > +{
> > + const int *ramp_table = lmu_bank->cfg->ramp_table;
> > + const int size = lmu_bank->cfg->size_ramp;
> > + unsigned int msec;
> > + int i;
> > +
> > + if (!ramp_table)
> > + return -EINVAL;
> > +
> > + switch (mode) {
> > + case BL_RAMP_UP:
> > + msec = lmu_bank->ramp_up_msec;
> > + break;
> > + case BL_RAMP_DOWN:
> > + msec = lmu_bank->ramp_down_msec;
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + if (msec <= ramp_table[0])
> > + return 0;
> > +
> > + if (msec > ramp_table[size - 1])
> > + return size - 1;
> > +
> > + for (i = 1; i < size; i++) {
> > + if (msec == ramp_table[i])
> > + return i;
> > +
> > + /* Find an approximate index by looking up the table */
> > + if (msec > ramp_table[i - 1] && msec < ramp_table[i]) {
> > + if (msec - ramp_table[i - 1] < ramp_table[i] - msec)
> > + return i - 1;
> > + else
> > + return i;
> > + }
> > + }
> > +
> > + return -EINVAL;
> > +}
> > +
> > +
>
> Extra new line
oops.
>
> > +static int ti_lmu_bl_set_ramp(struct ti_lmu_bank *lmu_bank)
> > +{
> > + struct regmap *regmap = lmu_bank->lmu->regmap;
> > + const struct ti_lmu_bl_reg *reginfo = lmu_bank->cfg->reginfo;
> > + int offset = reginfo->ramp_reg_offset;
> > + int i, ret, index;
> > + struct lmu_bl_reg_data regdata;
> > +
> > + for (i = BL_RAMP_UP; i <= BL_RAMP_DOWN; i++) {
> > + index = ti_lmu_bl_convert_ramp_to_index(lmu_bank, i);
> > + if (index > 0) {
> > + if (!reginfo->ramp)
> > + break;
> > +
> > + regdata = reginfo->ramp[i];
> > + if (lmu_bank->bank_id != 0)
> > + regdata.val += offset;
> > +
> > + /* regdata.val is shift bit */
> > + ret = regmap_update_bits(regmap, regdata.reg,
> > + regdata.mask,
> > + index << regdata.val);
> > + if (ret)
> > + return ret;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ti_lmu_bl_configure(struct ti_lmu_bank *lmu_bank)
> > +{
> > + int ret;
> > +
> > + ret = ti_lmu_bl_check_channel(lmu_bank);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ti_lmu_bl_create_channel(lmu_bank);
> > + if (ret)
> > + return ret;
> > +
> > + ret = ti_lmu_bl_update_ctrl_mode(lmu_bank);
> > + if (ret)
> > + return ret;
> > +
> > + return ti_lmu_bl_set_ramp(lmu_bank);
> > +}
> > +
> > +static int ti_lmu_bl_register_backlight(struct ti_lmu_bank *lmu_bank)
> > +{
> > + struct backlight_device *bl_dev;
> > + struct backlight_properties props;
> > +
> > + if (lmu_bank->type != TI_LMU_BL)
> > + return -EINVAL;
> > +
> > + memset(&props, 0, sizeof(struct backlight_properties));
> > + props.type = BACKLIGHT_PLATFORM;
> > + props.brightness = lmu_bank->default_brightness;
> > + props.max_brightness = lmu_bank->cfg->max_brightness;
> > +
> > + bl_dev = devm_backlight_device_register(lmu_bank->dev, lmu_bank->label,
> > + lmu_bank->dev, lmu_bank,
> > + &lmu_backlight_ops, &props);
> > + if (IS_ERR(bl_dev))
> > + return PTR_ERR(bl_dev);
> > +
> > + lmu_bank->backlight = bl_dev;
> > +
> > + return 0;
> > +}
> > +
> > +static int ti_lmu_bl_register_led(struct ti_lmu_bank *lmu_bank)
> > +{
> > + int err;
> > +
> > + if (lmu_bank->type != TI_LMU_LED)
> > + return -EINVAL;
> > +
> > + lmu_bank->led = devm_kzalloc(lmu_bank->dev, sizeof(*lmu_bank->led),
> > + GFP_KERNEL);
> > + if (!lmu_bank->led)
> > + return -ENOMEM;
> > +
> > + lmu_bank->led->name = lmu_bank->label;
> > + lmu_bank->led->max_brightness = lmu_bank->cfg->max_brightness;
> > + lmu_bank->led->brightness_set_blocking =
> > + ti_lmu_bl_set_led_blocking;
> > +
> > + err = devm_led_classdev_register(lmu_bank->dev, lmu_bank->led);
> > + if (err)
> > + return err;
> > +
> > + return 0;
> > +}
> > +
> > +static int ti_lmu_bl_add_device(struct ti_lmu_bank *lmu_bank)
> > +{
> > + switch (lmu_bank->type) {
> > + case TI_LMU_BL:
> > + return ti_lmu_bl_register_backlight(lmu_bank);
> > + case TI_LMU_LED:
> > + return ti_lmu_bl_register_led(lmu_bank);
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static int setup_of_node(struct platform_device *pdev)
>
> This seems a bit generic. Maybe keep with the naming convention
>
> ti_lmu_setup_of_node
right.
> > +{
> > + struct device_node *parent_node = pdev->dev.parent->of_node;
> > + char *name;
> > +
> > + if (!parent_node)
> > + return 0;
> > +
> > + name = kasprintf(GFP_KERNEL, "bank%d", pdev->id);
> > + if (!name)
> > + return -ENOMEM;
> > +
> > + pdev->dev.of_node = of_get_child_by_name(parent_node, name);
> > + kfree(name);
> > +
> > + if (!pdev->dev.of_node)
> > + return -ENODEV;
> > +
> > + return 0;
> > +}
> > +
> > +static int ti_lmu_parse_led_sources(struct device *dev)
> > +{
> > + unsigned long mask = 0;
> > + int ret;
> > + int size, i;
> > + u32 *leds;
> > +
> > + size = device_property_read_u32_array(dev, "ti,led-sources", NULL, 0);
> > + if (size <= 0) {
> > + dev_err(dev, "Missing or malformed property led-sources: %d\n",
> > + size);
> > + return size < 0 ? size : -EINVAL;
>
> Why the additional check? Why not just return -EINVAL?
I think it makes sense to pass the actual error code, but I can
simplify it when you insist.
> > + }
> > +
> > + leds = kmalloc_array(size, sizeof(u32), GFP_KERNEL);
> > + if (!leds)
> > + return -ENOMEM;
> > +
> > + ret = device_property_read_u32_array(dev, "ti,led-sources", leds, size);
> > + if (ret) {
> > + dev_err(dev, "Failed to read led-sources property: %d\n", ret);
> > + goto out;
> > + }
> > +
> > + for (i = 0; i < size; i++)
> > + set_bit(leds[i], &mask);
> > +
> > + ret = mask;
> > +
> > +out:
> > + kfree(leds);
> > + return ret;
> > +}
> > +
> > +static int ti_lmu_bl_init(struct ti_lmu_bank *lmu_bank)
> > +{
> > + struct regmap *regmap = lmu_bank->lmu->regmap;
> > + const struct lmu_bl_reg_data *regdata =
> > + lmu_bank->cfg->reginfo->init;
> > + int num_init = lmu_bank->cfg->reginfo->num_init;
> > + int i, ret;
> > +
> > + if (lmu_bank->lmu->backlight_initialized)
> > + return 0;
>
> Add a new line here
ok
> > + lmu_bank->lmu->backlight_initialized = true;
> > +
> > + for (i = 0; regdata && i < num_init; i++) {
> > + ret = regmap_update_bits(regmap, regdata->reg, regdata->mask,
> > + regdata->val);
> > + if (ret)
> > + return ret;
> > +
> > + regdata++;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ti_lmu_bl_reload(struct ti_lmu_bank *lmu_bank)
> > +{
> > + int err;
> > +
> > + ti_lmu_bl_init(lmu_bank);
> > +
> > + err = ti_lmu_bl_configure(lmu_bank);
> > + if (err)
> > + return err;
> > +
> > + return ti_lmu_bl_set_brightness(lmu_bank, lmu_bank->current_brightness);
> > +}
> > +
> > +static int ti_lmu_bl_monitor_notifier(struct notifier_block *nb,
> > + unsigned long action, void *unused)
> > +{
> > + struct ti_lmu_bank *lmu_bank = container_of(nb, struct ti_lmu_bank, nb);
> > +
> > + if (action == LMU_EVENT_MONITOR_DONE) {
> > + if (ti_lmu_bl_reload(lmu_bank))
> > + return NOTIFY_STOP;
> > + }
> > +
> > + return NOTIFY_OK;
> > +}
> > +
> > +static int ti_lmu_bl_probe(struct platform_device *pdev)
> > +{
> > + struct ti_lmu_bank *lmu_bank;
> > + int err;
> > +
> > + err = setup_of_node(pdev);
> > + if (err)
> > + return err;
> > +
> > + lmu_bank = devm_kzalloc(&pdev->dev, sizeof(*lmu_bank), GFP_KERNEL);
> > + if (!lmu_bank)
> > + return -ENOMEM;
>
> Add a new line here
ok
> > + lmu_bank->dev = &pdev->dev;
> > + dev_set_drvdata(&pdev->dev, lmu_bank);
> > +
> > + err = device_property_read_string(&pdev->dev, "label",
> > + &lmu_bank->label);
> > + if (err)
> > + return err;
> > +
> > + lmu_bank->type = TI_LMU_BL;
> > + if (!strcmp(lmu_bank->label, "keyboard")) {
> > + lmu_bank->type = TI_LMU_LED;
> > + lmu_bank->label = "kbd_backlight";
>
> What is the reason for changing the label? Why can't the label in
> the DT be kbd_backlight?
It can, I tried to avoid Linuxism in DT.
> > + }
> > +
> > + lmu_bank->leds = ti_lmu_parse_led_sources(&pdev->dev);
> > + if (lmu_bank->leds < 0)
> > + return lmu_bank->leds;
> > + else if (lmu_bank->leds == 0)
> > + return -EINVAL;
> > +
> > + device_property_read_u32(&pdev->dev, "default-brightness-level",
> > + &lmu_bank->default_brightness);
> > + device_property_read_u32(&pdev->dev, "ti,ramp-up-ms",
> > + &lmu_bank->ramp_up_msec);
> > + device_property_read_u32(&pdev->dev, "ti,ramp-down-ms",
> > + &lmu_bank->ramp_down_msec);
> > + device_property_read_u32(&pdev->dev, "pwm-period",
> > + &lmu_bank->pwm_period);
> > +
> > + if (lmu_bank->pwm_period > 0)
> > + lmu_bank->mode = BL_PWM_BASED;
> > + else
> > + lmu_bank->mode = BL_REGISTER_BASED;
> > +
> > + lmu_bank->lmu = dev_get_drvdata(pdev->dev.parent);
> > + lmu_bank->cfg = &lmu_bl_cfg[lmu_bank->lmu->id];
> > + lmu_bank->bank_id = pdev->id;
> > +
> > + ti_lmu_bl_init(lmu_bank);
> > +
> > + err = ti_lmu_bl_configure(lmu_bank);
> > + if (err)
> > + return err;
> > +
> > + err = ti_lmu_bl_add_device(lmu_bank);
> > + if (err)
> > + return err;
> > +
> > + err = ti_lmu_bl_set_brightness(lmu_bank,
> > + lmu_bank->default_brightness);
> > + if (err)
> > + return err;
> > +
> > + /*
> > + * Notifier callback is required because backlight device needs
> > + * reconfiguration after fault detection procedure is done by
> > + * ti-lmu-fault-monitor driver.
> > + */
> > + if (lmu_bank->cfg->fault_monitor_used) {
> > + lmu_bank->nb.notifier_call = ti_lmu_bl_monitor_notifier;
> > + err = blocking_notifier_chain_register(&lmu_bank->lmu->notifier,
> > + &lmu_bank->nb);
> > + if (err)
> > + return err;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int ti_lmu_bl_remove(struct platform_device *pdev)
> > +{
> > + struct ti_lmu_bank *lmu_bank = platform_get_drvdata(pdev);
> > +
> > + if (lmu_bank->cfg->fault_monitor_used)
> > + blocking_notifier_chain_unregister(&lmu_bank->lmu->notifier,
> > + &lmu_bank->nb);
> > +
> > + ti_lmu_bl_set_brightness(lmu_bank, 0);
> > +
> > + return 0;
> > +}
> > +
> > +static struct platform_driver ti_lmu_bl_driver = {
> > + .probe = ti_lmu_bl_probe,
> > + .remove = ti_lmu_bl_remove,
> > + .driver = {
> > + .name = "ti-lmu-led-backlight",
> > + },
> > +};
> > +module_platform_driver(ti_lmu_bl_driver)
> > +
> > +MODULE_DESCRIPTION("TI LMU Backlight LED Driver");
> > +MODULE_AUTHOR("Sebastian Reichel");
> > +MODULE_LICENSE("GPL v2");
> > +MODULE_ALIAS("platform:ti-lmu-led-backlight");
> > diff --git a/drivers/video/backlight/ti-lmu-backlight-data.c b/drivers/video/backlight/ti-lmu-backlight-data.c
> > new file mode 100644
> > index 000000000000..583136cb934d
> > --- /dev/null
> > +++ b/drivers/video/backlight/ti-lmu-backlight-data.c
> > @@ -0,0 +1,304 @@
> > +/*
>
> Inconsistent licensing here the core has
> // SPDX-License-Identifier: GPL-2.0
>
> > + * TI LMU (Lighting Management Unit) Backlight Device Data
> > + *
> > + * Copyright 2015 Texas Instruments
>
> Copyright?
The original driver is from Milo Kim / TI. I changed almost all of
the core driver, so I took the liberty to update the copyright and
license header. The data part has been taken over almost unmodified,
so I kept the original header. I suppose TI is fine with using the
abbreviated header?
> > + * Author: Milo Kim <milo.kim@xxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#include "ti-lmu-backlight-data.h"
> > +
> > +/* LM3532 */
> > +static const struct lmu_bl_reg_data lm3532_init_data[] = {
> > + { LM3532_REG_ZONE_CFG_A, LM3532_ZONE_MASK, LM3532_ZONE_0 },
> > + { LM3532_REG_ZONE_CFG_B, LM3532_ZONE_MASK, LM3532_ZONE_1 },
> > + { LM3532_REG_ZONE_CFG_C, LM3532_ZONE_MASK, LM3532_ZONE_2 },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3532_channel_data[] = {
> > + { LM3532_REG_OUTPUT_CFG, LM3532_ILED1_CFG_MASK,
> > + LM3532_ILED1_CFG_SHIFT },
> > + { LM3532_REG_OUTPUT_CFG, LM3532_ILED2_CFG_MASK,
> > + LM3532_ILED2_CFG_SHIFT },
> > + { LM3532_REG_OUTPUT_CFG, LM3532_ILED3_CFG_MASK,
> > + LM3532_ILED3_CFG_SHIFT },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3532_mode_data[] = {
> > + { LM3532_REG_PWM_A_CFG, LM3532_PWM_A_MASK, LM3532_PWM_ZONE_0 },
> > + { LM3532_REG_PWM_B_CFG, LM3532_PWM_B_MASK, LM3532_PWM_ZONE_1 },
> > + { LM3532_REG_PWM_C_CFG, LM3532_PWM_C_MASK, LM3532_PWM_ZONE_2 },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3532_ramp_data[] = {
> > + { LM3532_REG_RAMPUP, LM3532_RAMPUP_MASK, LM3532_RAMPUP_SHIFT },
> > + { LM3532_REG_RAMPDN, LM3532_RAMPDN_MASK, LM3532_RAMPDN_SHIFT },
> > +};
> > +
> > +static u8 lm3532_enable_reg = LM3532_REG_ENABLE;
> > +
> > +static u8 lm3532_brightness_regs[] = {
> > + LM3532_REG_BRT_A,
> > + LM3532_REG_BRT_B,
> > + LM3532_REG_BRT_C,
> > +};
> > +
> > +static const struct ti_lmu_bl_reg lm3532_reg_info = {
> > + .init = lm3532_init_data,
> > + .num_init = ARRAY_SIZE(lm3532_init_data),
> > + .channel = lm3532_channel_data,
> > + .mode = lm3532_mode_data,
> > + .ramp = lm3532_ramp_data,
> > + .enable = &lm3532_enable_reg,
> > + .brightness_msb = lm3532_brightness_regs,
> > +};
> > +
> > +/* LM3631 */
> > +static const struct lmu_bl_reg_data lm3631_init_data[] = {
> > + { LM3631_REG_BRT_MODE, LM3631_MODE_MASK, LM3631_DEFAULT_MODE },
> > + { LM3631_REG_BL_CFG, LM3631_MAP_MASK, LM3631_EXPONENTIAL_MAP },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3631_channel_data[] = {
> > + { LM3631_REG_BL_CFG, LM3631_BL_CHANNEL_MASK, LM3631_BL_SINGLE_CHANNEL },
> > + { LM3631_REG_BL_CFG, LM3631_BL_CHANNEL_MASK, LM3631_BL_DUAL_CHANNEL },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3631_ramp_data[] = {
> > + { LM3631_REG_SLOPE, LM3631_SLOPE_MASK, LM3631_SLOPE_SHIFT },
> > +};
> > +
> > +static u8 lm3631_enable_reg = LM3631_REG_DEVCTRL;
> > +static u8 lm3631_brightness_msb_reg = LM3631_REG_BRT_MSB;
> > +static u8 lm3631_brightness_lsb_reg = LM3631_REG_BRT_LSB;
> > +
> > +static const struct ti_lmu_bl_reg lm3631_reg_info = {
> > + .init = lm3631_init_data,
> > + .num_init = ARRAY_SIZE(lm3631_init_data),
> > + .channel = lm3631_channel_data,
> > + .ramp = lm3631_ramp_data,
> > + .enable = &lm3631_enable_reg,
> > + .brightness_msb = &lm3631_brightness_msb_reg,
> > + .brightness_lsb = &lm3631_brightness_lsb_reg,
> > +};
> > +
> > +/* LM3632 */
> > +static const struct lmu_bl_reg_data lm3632_init_data[] = {
> > + { LM3632_REG_CONFIG1, LM3632_OVP_MASK, LM3632_OVP_25V },
> > + { LM3632_REG_CONFIG2, LM3632_SWFREQ_MASK, LM3632_SWFREQ_1MHZ },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3632_channel_data[] = {
> > + { LM3632_REG_ENABLE, LM3632_BL_CHANNEL_MASK, LM3632_BL_SINGLE_CHANNEL },
> > + { LM3632_REG_ENABLE, LM3632_BL_CHANNEL_MASK, LM3632_BL_DUAL_CHANNEL },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3632_mode_data[] = {
> > + { LM3632_REG_IO_CTRL, LM3632_PWM_MASK, LM3632_PWM_MODE },
> > +};
> > +
> > +static u8 lm3632_enable_reg = LM3632_REG_ENABLE;
> > +static u8 lm3632_brightness_msb_reg = LM3632_REG_BRT_MSB;
> > +static u8 lm3632_brightness_lsb_reg = LM3632_REG_BRT_LSB;
> > +
> > +static const struct ti_lmu_bl_reg lm3632_reg_info = {
> > + .init = lm3632_init_data,
> > + .num_init = ARRAY_SIZE(lm3632_init_data),
> > + .channel = lm3632_channel_data,
> > + .mode = lm3632_mode_data,
> > + .enable = &lm3632_enable_reg,
> > + .brightness_msb = &lm3632_brightness_msb_reg,
> > + .brightness_lsb = &lm3632_brightness_lsb_reg,
> > +};
> > +
> > +/* LM3633 */
> > +static const struct lmu_bl_reg_data lm3633_init_data[] = {
> > + { LM3633_REG_BOOST_CFG, LM3633_OVP_MASK, LM3633_OVP_40V },
> > + { LM3633_REG_BL_RAMP_CONF, LM3633_BL_RAMP_MASK, LM3633_BL_RAMP_EACH },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3633_channel_data[] = {
> > + { LM3633_REG_HVLED_OUTPUT_CFG, LM3633_HVLED1_CFG_MASK,
> > + LM3633_HVLED1_CFG_SHIFT },
> > + { LM3633_REG_HVLED_OUTPUT_CFG, LM3633_HVLED2_CFG_MASK,
> > + LM3633_HVLED2_CFG_SHIFT },
> > + { LM3633_REG_HVLED_OUTPUT_CFG, LM3633_HVLED3_CFG_MASK,
> > + LM3633_HVLED3_CFG_SHIFT },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3633_mode_data[] = {
> > + { LM3633_REG_PWM_CFG, LM3633_PWM_A_MASK, LM3633_PWM_A_MASK },
> > + { LM3633_REG_PWM_CFG, LM3633_PWM_B_MASK, LM3633_PWM_B_MASK },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3633_ramp_data[] = {
> > + { LM3633_REG_BL0_RAMP, LM3633_BL_RAMPUP_MASK, LM3633_BL_RAMPUP_SHIFT },
> > + { LM3633_REG_BL0_RAMP, LM3633_BL_RAMPDN_MASK, LM3633_BL_RAMPDN_SHIFT },
> > +};
> > +
> > +static u8 lm3633_enable_reg = LM3633_REG_ENABLE;
> > +
> > +static u8 lm3633_brightness_msb_regs[] = {
> > + LM3633_REG_BRT_HVLED_A_MSB,
> > + LM3633_REG_BRT_HVLED_B_MSB,
> > +};
> > +
> > +static u8 lm3633_brightness_lsb_regs[] = {
> > + LM3633_REG_BRT_HVLED_A_LSB,
> > + LM3633_REG_BRT_HVLED_B_LSB,
> > +};
> > +
> > +static const struct ti_lmu_bl_reg lm3633_reg_info = {
> > + .init = lm3633_init_data,
> > + .num_init = ARRAY_SIZE(lm3633_init_data),
> > + .channel = lm3633_channel_data,
> > + .mode = lm3633_mode_data,
> > + .ramp = lm3633_ramp_data,
> > + .ramp_reg_offset = 1, /* For LM3633_REG_BL1_RAMPUP/DN */
> > + .enable = &lm3633_enable_reg,
> > + .brightness_msb = lm3633_brightness_msb_regs,
> > + .brightness_lsb = lm3633_brightness_lsb_regs,
> > +};
> > +
> > +/* LM3695 */
> > +static const struct lmu_bl_reg_data lm3695_init_data[] = {
> > + { LM3695_REG_GP, LM3695_BRT_RW_MASK, LM3695_BRT_RW_MASK },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3695_channel_data[] = {
> > + { LM3695_REG_GP, LM3695_BL_CHANNEL_MASK, LM3695_BL_SINGLE_CHANNEL },
> > + { LM3695_REG_GP, LM3695_BL_CHANNEL_MASK, LM3695_BL_DUAL_CHANNEL },
> > +};
> > +
> > +static u8 lm3695_enable_reg = LM3695_REG_GP;
> > +static u8 lm3695_brightness_msb_reg = LM3695_REG_BRT_MSB;
> > +static u8 lm3695_brightness_lsb_reg = LM3695_REG_BRT_LSB;
> > +
> > +static const struct ti_lmu_bl_reg lm3695_reg_info = {
> > + .init = lm3695_init_data,
> > + .num_init = ARRAY_SIZE(lm3695_init_data),
> > + .channel = lm3695_channel_data,
> > + .enable = &lm3695_enable_reg,
> > + .enable_usec = 600,
> > + .brightness_msb = &lm3695_brightness_msb_reg,
> > + .brightness_lsb = &lm3695_brightness_lsb_reg,
> > +};
> > +
> > +/* LM3697 */
> > +static const struct lmu_bl_reg_data lm3697_init_data[] = {
> > + { LM3697_REG_RAMP_CONF, LM3697_RAMP_MASK, LM3697_RAMP_EACH },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3697_channel_data[] = {
> > + { LM3697_REG_HVLED_OUTPUT_CFG, LM3697_HVLED1_CFG_MASK,
> > + LM3697_HVLED1_CFG_SHIFT },
> > + { LM3697_REG_HVLED_OUTPUT_CFG, LM3697_HVLED2_CFG_MASK,
> > + LM3697_HVLED2_CFG_SHIFT },
> > + { LM3697_REG_HVLED_OUTPUT_CFG, LM3697_HVLED3_CFG_MASK,
> > + LM3697_HVLED3_CFG_SHIFT },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3697_mode_data[] = {
> > + { LM3697_REG_PWM_CFG, LM3697_PWM_A_MASK, LM3697_PWM_A_MASK },
> > + { LM3697_REG_PWM_CFG, LM3697_PWM_B_MASK, LM3697_PWM_B_MASK },
> > +};
> > +
> > +static const struct lmu_bl_reg_data lm3697_ramp_data[] = {
> > + { LM3697_REG_BL0_RAMP, LM3697_RAMPUP_MASK, LM3697_RAMPUP_SHIFT },
> > + { LM3697_REG_BL0_RAMP, LM3697_RAMPDN_MASK, LM3697_RAMPDN_SHIFT },
> > +};
> > +
> > +static u8 lm3697_enable_reg = LM3697_REG_ENABLE;
> > +
> > +static u8 lm3697_brightness_msb_regs[] = {
> > + LM3697_REG_BRT_A_MSB,
> > + LM3697_REG_BRT_B_MSB,
> > +};
> > +
> > +static u8 lm3697_brightness_lsb_regs[] = {
> > + LM3697_REG_BRT_A_LSB,
> > + LM3697_REG_BRT_B_LSB,
> > +};
> > +
> > +static const struct ti_lmu_bl_reg lm3697_reg_info = {
> > + .init = lm3697_init_data,
> > + .num_init = ARRAY_SIZE(lm3697_init_data),
> > + .channel = lm3697_channel_data,
> > + .mode = lm3697_mode_data,
> > + .ramp = lm3697_ramp_data,
> > + .ramp_reg_offset = 1, /* For LM3697_REG_BL1_RAMPUP/DN */
> > + .enable = &lm3697_enable_reg,
> > + .brightness_msb = lm3697_brightness_msb_regs,
> > + .brightness_lsb = lm3697_brightness_lsb_regs,
> > +};
> > +
> > +static int lm3532_ramp_table[] = { 0, 1, 2, 4, 8, 16, 32, 65 };
> > +
> > +static int lm3631_ramp_table[] = {
> > + 0, 1, 2, 5, 10, 20, 50, 100,
> > + 250, 500, 750, 1000, 1500, 2000, 3000, 4000,
> > +};
> > +
> > +static int common_ramp_table[] = {
> > + 2, 250, 500, 1000, 2000, 4000, 8000, 16000,
> > +};
> > +
> > +#define LM3532_MAX_CHANNELS 3
> > +#define LM3631_MAX_CHANNELS 2
> > +#define LM3632_MAX_CHANNELS 2
> > +#define LM3633_MAX_CHANNELS 3
> > +#define LM3695_MAX_CHANNELS 2
> > +#define LM3697_MAX_CHANNELS 3
> > +
> > +const struct ti_lmu_bl_cfg lmu_bl_cfg[LMU_MAX_ID] = {
> > + {
> > + .reginfo = &lm3532_reg_info,
> > + .num_channels = LM3532_MAX_CHANNELS,
> > + .max_brightness = MAX_BRIGHTNESS_8BIT,
> > + .pwm_action = UPDATE_PWM_AND_BRT_REGISTER,
> > + .ramp_table = lm3532_ramp_table,
> > + .size_ramp = ARRAY_SIZE(lm3532_ramp_table),
> > + },
> > + {
> > + .reginfo = &lm3631_reg_info,
> > + .num_channels = LM3631_MAX_CHANNELS,
> > + .max_brightness = MAX_BRIGHTNESS_11BIT,
> > + .pwm_action = UPDATE_PWM_ONLY,
> > + .ramp_table = lm3631_ramp_table,
> > + .size_ramp = ARRAY_SIZE(lm3631_ramp_table),
> > + },
> > + {
> > + .reginfo = &lm3632_reg_info,
> > + .num_channels = LM3632_MAX_CHANNELS,
> > + .max_brightness = MAX_BRIGHTNESS_11BIT,
> > + .pwm_action = UPDATE_PWM_ONLY,
> > + },
> > + {
> > + .reginfo = &lm3633_reg_info,
> > + .num_channels = LM3633_MAX_CHANNELS,
> > + .max_brightness = MAX_BRIGHTNESS_11BIT,
> > + .pwm_action = UPDATE_MAX_BRT,
> > + .ramp_table = common_ramp_table,
> > + .size_ramp = ARRAY_SIZE(common_ramp_table),
> > + .fault_monitor_used = true,
> > + },
> > + {
> > + .reginfo = &lm3695_reg_info,
> > + .num_channels = LM3695_MAX_CHANNELS,
> > + .max_brightness = MAX_BRIGHTNESS_11BIT,
> > + .pwm_action = UPDATE_PWM_AND_BRT_REGISTER,
> > + },
> > + {
> > + .reginfo = &lm3697_reg_info,
> > + .num_channels = LM3697_MAX_CHANNELS,
> > + .max_brightness = MAX_BRIGHTNESS_11BIT,
> > + .pwm_action = UPDATE_PWM_AND_BRT_REGISTER,
> > + .ramp_table = common_ramp_table,
> > + .size_ramp = ARRAY_SIZE(common_ramp_table),
> > + .fault_monitor_used = true,
> > + },
> > +};
> > diff --git a/drivers/video/backlight/ti-lmu-backlight-data.h b/drivers/video/backlight/ti-lmu-backlight-data.h
> > new file mode 100644
> > index 000000000000..c64e8e6513e1
> > --- /dev/null
> > +++ b/drivers/video/backlight/ti-lmu-backlight-data.h
> > @@ -0,0 +1,95 @@
> > +/*
>
> Inconsistent licensing here the core has
> // SPDX-License-Identifier: GPL-2.0
See above.
> > + * TI LMU (Lighting Management Unit) Backlight Device Data Definitions
> > + *
> > + * Copyright 2015 Texas Instruments
> > + *
> > + * Author: Milo Kim <milo.kim@xxxxxx>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + */
> > +
> > +#ifndef __TI_LMU_BACKLIGHT_H__
> > +#define __TI_LMU_BACKLIGHT_H__
> > +
> > +#include <linux/mfd/ti-lmu.h>
> > +#include <linux/mfd/ti-lmu-register.h>
> > +
> > +#define MAX_BRIGHTNESS_8BIT 255
> > +#define MAX_BRIGHTNESS_11BIT 2047
> > +
> > +enum ti_lmu_bl_pwm_action {
> > + /* Update PWM duty, no brightness register update is required */
> > + UPDATE_PWM_ONLY,
> > + /* Update not only duty but also brightness register */
> > + UPDATE_PWM_AND_BRT_REGISTER,
> > + /* Update max value in brightness registers */
> > + UPDATE_MAX_BRT,
> > +};
> > +
> > +struct lmu_bl_reg_data {
> > + u8 reg;
> > + u8 mask;
> > + u8 val;
> > +};
> > +
> > +/**
> > + * struct ti_lmu_bl_reg
> > + *
> > + * @init: Device initialization registers
> > + * @num_init: Numbers of initialization registers
> > + * @channel: Backlight channel configuration registers
> > + * @mode: Brightness control mode registers
> > + * @ramp: Ramp registers for lighting effect
> > + * @ramp_reg_offset: Ramp register offset.
> > + * Only used for multiple ramp registers.
> > + * @enable: Enable control register address
> > + * @enable_usec: Delay time for updating enable register.
> > + * Unit is microsecond.
> > + * @brightness_msb: Brightness MSB(Upper 8 bits) registers.
> > + * Concatenated with LSB in 11 bit dimming mode.
> > + * In 8 bit dimming, only MSB is used.
> > + * @brightness_lsb: Brightness LSB(Lower 3 bits) registers.
> > + * Only valid in 11 bit dimming mode.
> > + */
> > +struct ti_lmu_bl_reg {
> > + const struct lmu_bl_reg_data *init;
> > + int num_init;
> > + const struct lmu_bl_reg_data *channel;
> > + const struct lmu_bl_reg_data *mode;
> > + const struct lmu_bl_reg_data *ramp;
> > + int ramp_reg_offset;
> > + u8 *enable;
> > + unsigned long enable_usec;
> > + u8 *brightness_msb;
> > + u8 *brightness_lsb;
> > +};
> > +
> > +/**
> > + * struct ti_lmu_bl_cfg
> > + *
> > + * @reginfo: Device register configuration
> > + * @num_channels: Number of backlight channels
> > + * @max_brightness: Max brightness value of backlight device
> > + * @pwm_action: How to control brightness registers in PWM mode
> > + * @ramp_table: [Optional] Ramp time table for lighting effect.
> > + * It's used for searching approximate register index.
> > + * @size_ramp: [Optional] Size of ramp table
> > + * @fault_monitor_used: [Optional] Set true if the device needs to handle
> > + * LMU fault monitor event.
> > + *
> > + * This structure is used for device specific data configuration.
> > + */
> > +struct ti_lmu_bl_cfg {
> > + const struct ti_lmu_bl_reg *reginfo;
> > + int num_channels;
> > + int max_brightness;
> > + enum ti_lmu_bl_pwm_action pwm_action;
> > + int *ramp_table;
> > + int size_ramp;
> > + bool fault_monitor_used;
> > +};
> > +
> > +extern const struct ti_lmu_bl_cfg lmu_bl_cfg[LMU_MAX_ID];
> > +#endif
> >
-- Sebastian
Attachment:
signature.asc
Description: PGP signature
