The Allwinner SoCs usually come with a DSI encoder. Add a binding for it.
Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
Signed-off-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxx>
---
Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt | 93 +++++++-
1 file changed, 93 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
diff --git a/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
new file mode 100644
index 000000000000..6a6cf5de08b0
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
@@ -0,0 +1,93 @@
+Allwinner A31 DSI Encoder
+=========================
+
+The DSI pipeline consists of two separate blocks: the DSI controller
+itself, and its associated D-PHY.
+
+DSI Encoder
+-----------
+
+The DSI Encoder generates the DSI signal from the TCON's.
+
+Required properties:
+ - compatible: value must be one of:
+ * allwinner,sun6i-a31-mipi-dsi
+ - reg: base address and size of memory-mapped region
+ - interrupts: interrupt associated to this IP
+ - clocks: phandles to the clocks feeding the DSI encoder
+ * bus: the DSI interface clock
+ * mod: the DSI module clock
+ - clock-names: the clock names mentioned above
+ - phys: phandle to the D-PHY
+ - phy-names: must be "dphy"
+ - resets: phandle to the reset controller driving the encoder
+
+ - ports: A ports node with endpoint definitions as defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt. The
+ first port should be the input endpoint, usually coming from the
+ associated TCON.
+
+Any MIPI-DSI device attached to this should be described according to
+the bindings defined in ../mipi-dsi-bus.txt
+
+D-PHY
+-----
+
+Required properties:
+ - compatible: value must be one of:
+ * allwinner,sun6i-a31-mipi-dphy
+ - reg: base address and size of memory-mapped region
+ - clocks: phandles to the clocks feeding the DSI encoder
+ * bus: the DSI interface clock
+ * mod: the DSI module clock
+ - clock-names: the clock names mentioned above
+ - resets: phandle to the reset controller driving the encoder
+
+Example:
+
+dsi0: dsi@1ca0000 {
+ compatible = "allwinner,sun6i-a31-mipi-dsi";
+ reg = <0x01ca0000 0x1000>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_MIPI_DSI>,
+ <&ccu CLK_DSI_SCLK>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_MIPI_DSI>;
+ phys = <&dphy0>;
+ phy-names = "dphy";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ panel@0 {
+ compatible = "bananapi,lhr050h41", "ilitek,ili9881c";
+ reg = <0>;
+ power-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* PB07 */
+ reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL05 */
+ backlight = <&pwm_bl>;
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ dsi0_in_tcon0: endpoint {
+ remote-endpoint = <&tcon0_out_dsi0>;
+ };
+ };
+ };
+};
+
+dphy0: d-phy@1ca1000 {
+ compatible = "allwinner,sun6i-a31-mipi-dphy";
+ reg = <0x01ca1000 0x1000>;
+ clocks = <&ccu CLK_BUS_MIPI_DSI>,
+ <&ccu CLK_DSI_DPHY>;
+ clock-names = "bus", "mod";
+ resets = <&ccu RST_BUS_MIPI_DSI>;
+ #phy-cells = <0>;
+};
--
git-series 0.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
