Hi again,
On Wednesday, 4 April 2018 01:28:29 EEST Laurent Pinchart wrote:
> On Wednesday, 28 March 2018 10:08:26 EEST Daniel Vetter wrote:
> > On Mon, Mar 26, 2018 at 11:24:42PM +0200, Peter Rosin wrote:
> > > Hi!
> > >
> > > [I got to v2 sooner than expected]
> > >
> > > I have an Atmel sama5d31 hooked up to an lvds encoder and then
> > > on to an lvds panel. Which seems like something that has been
> > > done one or two times before...
> > >
> > > The problem is that the bus_format of the SoC and the panel do
> > > not agree. The SoC driver (atmel-hlcdc) can handle the
> > > rgb444, rgb565, rgb666 and rgb888 bus formats. The hardware is
> > > wired for the rgb565 case. The lvds encoder supports rgb888 on
> > > its input side with the LSB wires for each color simply pulled
> > > down internally in the encoder in my case which means that the
> > > rgb565 bus_format is the format that works best. And the panel
> > > is expecting lvds (vesa-24), which is what the encoder outputs.
> > >
> > > The reason I "blame" the bus_format of the drm_connector is that
> > > with the below DT snippet, things do not work *exactly* due to
> > > that. At least, it starts to work if I hack the panel-lvds driver
> > > to report the rgb565 bus_format instead of vesa-24.
> > >
> > > panel: panel {
> > > compatible = "panel-lvds";
> > >
> > > width-mm = <304>;
> > > height-mm = <228;
> > >
> > > data-mapping = "vesa-24";
> > >
> > > panel-timing {
> > > // 1024x768 @ 60Hz (typical)
> > > clock-frequency = <52140000 65000000 71100000>;
> > > hactive = <1024>;
> > > vactive = <768>;
> > > hfront-porch = <48 88 88>;
> > > hback-porch = <96 168 168>;
> > > hsync-len = <32 64 64>;
> > > vfront-porch = <8 13 14>;
> > > vback-porch = <8 13 14>;
> > > vsync-len = <8 12 14>;
> > > };
> > >
> > > port {
> > > panel_input: endpoint {
> > > remote-endpoint = <&lvds_encoder_output>;
> > > };
> > > };
> > > };
> > >
> > > lvds-encoder {
> > > compatible = "ti,ds90c185", "lvds-encoder";
> > >
> > > ports {
> > > #address-cells = <1>;
> > > #size-cells = <0>;
> > >
> > > port@0 {
> > > reg = <0>;
> > >
> > > lvds_encoder_input: endpoint {
> > > remote-endpoint = <&hlcdc_output>;
> > > };
> > > };
> > >
> > > port@1 {
> > > reg = <1>;
> > >
> > > lvds_encoder_output: endpoint {
> > > remote-endpoint = <&panel_input>;
> > > };
> > > };
> > > };
> > > };
> > >
> > > But, instead of perverting the panel-lvds driver with support
> > > for a totally fake non-lvds bus_format, I intruduce an API that allows
> > > display controller drivers to query the required bus_format of any
> > > intermediate bridges, and match up with that instead of the formats
> > > given by the drm_connector. I trigger this with this addition to the
> > >
> > > lvds-encoder DT node:
> > > interface-pix-fmt = "rgb565";
> > >
> > > Naming is hard though, so I'm not sure if that's good?
> > >
> > > I threw in the first patch, since that is the actual lvds encoder
> > > I have in this case.
> > >
> > > Suggestions welcome.
> >
> > Took a quick look, feels rather un-atomic. And there's beend discussing
> > for other bridge related state that we might want to track (like the full
> > adjusted_mode that might need to be adjusted at each stage in the chain).
> > So here's my suggestions:
> >
> > - Add an optional per-bridge internal state struct using the support in
> >
> > https://dri.freedesktop.org/docs/drm/gpu/drm-kms.html#handling-driver-priv
> > at e-state
> >
> > Yes it says "driver private", but since bridge is just helper stuff
> > that's all included. "driver private" == "not exposed as uapi" here.
> > Include all the usual convenience wrappers to get at the state for a
> > bridge.
> >
> > - Then stuff your bus_format into that new drm_bridge_state struct.
> >
> > - Add a new bridge callback atomic_check, which gets that bridge state as
> > parameter (similar to all the other atomic_check functions).
> >
> > This way we can even handle the bus_format dynamically, through the atomic
> > framework your bridge's atomic_check callback can look at the entire
> > atomic state (both up and down the chain if needed), it all neatly fits
> > into atomic overall and it's much easier to extend.
>
> While I think we'll eventually need bridge states, I don't think that's need
> yet. The bus formats reported by this patch series are static. We're not
> talking about the currently configured format for a bridge, but about the
> list of supported formats. This is similar to the bus_formats field present
> in the drm_display_info structure. There is thus in my opinion no need to
> interface this with atomic until we need to track the current format (and I
> think that will indeed happen at some point, but I don't think Peter needs
> this feature for now). That's why I've told Peter that I would like a
> bridge API to report the information and haven't requested a state-based
> implementation.
Reading patch 5/5 I fear this might not be so simple. I'll sleep over it and
try to comment tomorrow.
> > Please also cc Laurent Pinchart on this.
> >
> > > Changes since v1 https://lkml.org/lkml/2018/3/17/221
> > > - Add a proper bridge API to query the bus_format instead of abusing
> > > the ->get_modes part of the code. This is cleaner but requires
> > > changes to all display controller drivers wishing to participate.
> > > - Add patch to adjust the atmel-hlcdc driver according to the above.
> > > - Hook the new info into the bridge local to the lvds-encoder instead
> > > of messing about with new interfaces for the panel-bridge driver.
> > > - Add patch with a DT parsing function of bus_formats in a central
> > > place.
> > > - Rephrase the addition of ti,ds90c185 to the lvds-transmitter binding.
> > >
> > > Peter Rosin (5):
> > > dt-bindings: display: bridge: lvds-transmitter: add ti,ds90c185
> > > drm: bridge: add API to query the expected input formats of bridges
> > > drm: of: add display bus-format parser
> > > drm: bridge: lvds-encoder: allow specifying the input bus format
> > > drm/atmel-hlcdc: take bridges into account when selecting output
> > > format
> > >
> > > .../bindings/display/bridge/lvds-transmitter.txt | 14 ++++-
> > > .../devicetree/bindings/display/bus-format.txt | 35 +++++++++++++
> > > drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c | 49 +++++++++++++--
> > > drivers/gpu/drm/bridge/lvds-encoder.c | 25 +++++++++
> > > drivers/gpu/drm/drm_bridge.c | 32 ++++++++++++
> > > drivers/gpu/drm/drm_of.c | 59 +++++++++++++++
> > > include/drm/drm_bridge.h | 18 +++++++
> > > include/drm/drm_of.h | 9 ++++
> > > 8 files changed, 237 insertions(+), 4 deletions(-)
> > > create mode 100644
> > > Documentation/devicetree/bindings/display/bus-format.txt
--
Regards,
Laurent Pinchart
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
