On 3/27/2018 11:16 PM, Bjorn Andersson wrote:
> On Fri 23 Mar 03:18 PDT 2018, Sricharan R wrote:
>
>> The driver/phy support for ipq8074 is available now.
>> So enabling the nodes in DT.
>>
>
> Acked-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
>
Thanks.
Regards,
Sricharan
> Regards,
> Bjorn
>
>> Reviewed-by: Abhishek Sahu <absahu@xxxxxxxxxxxxxx>
>> Signed-off-by: Sricharan R <sricharan@xxxxxxxxxxxxxx>
>> ---
>> arch/arm64/boot/dts/qcom/ipq8074.dtsi | 157 +++++++++++++++++++++++++++++++++-
>> 1 file changed, 156 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
>> index a8dbbf0..caf3485 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
>> @@ -24,7 +24,7 @@
>> ranges = <0 0 0 0xffffffff>;
>> compatible = "simple-bus";
>>
>> - pinctrl@1000000 {
>> + tlmm: pinctrl@1000000 {
>> compatible = "qcom,ipq8074-pinctrl";
>> reg = <0x1000000 0x300000>;
>> interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
>> @@ -229,6 +229,161 @@
>> dma-names = "tx", "rx", "cmd";
>> status = "disabled";
>> };
>> +
>> + pcie_phy0: phy@86000 {
>> + compatible = "qcom,ipq8074-qmp-pcie-phy";
>> + reg = <0x86000 0x1000>;
>> + #phy-cells = <0>;
>> + clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
>> + clock-names = "pipe_clk";
>> + clock-output-names = "pcie20_phy0_pipe_clk";
>> +
>> + resets = <&gcc GCC_PCIE0_PHY_BCR>,
>> + <&gcc GCC_PCIE0PHY_PHY_BCR>;
>> + reset-names = "phy",
>> + "common";
>> + status = "disabled";
>> + };
>> +
>> + pcie0: pci@20000000 {
>> + compatible = "qcom,pcie-ipq8074";
>> + reg = <0x20000000 0xf1d
>> + 0x20000f20 0xa8
>> + 0x80000 0x2000
>> + 0x20100000 0x1000>;
>> + reg-names = "dbi", "elbi", "parf", "config";
>> + device_type = "pci";
>> + linux,pci-domain = <0>;
>> + bus-range = <0x00 0xff>;
>> + num-lanes = <1>;
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> +
>> + phys = <&pcie_phy0>;
>> + phy-names = "pciephy";
>> +
>> + ranges = <0x81000000 0 0x20200000 0x20200000
>> + 0 0x100000 /* downstream I/O */
>> + 0x82000000 0 0x20300000 0x20300000
>> + 0 0xd00000>; /* non-prefetchable memory */
>> +
>> + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "msi";
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 0x7>;
>> + interrupt-map = <0 0 0 1 &intc 0 75
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_a */
>> + <0 0 0 2 &intc 0 78
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_b */
>> + <0 0 0 3 &intc 0 79
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_c */
>> + <0 0 0 4 &intc 0 83
>> + IRQ_TYPE_LEVEL_HIGH>; /* int_d */
>> +
>> + clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
>> + <&gcc GCC_PCIE0_AXI_M_CLK>,
>> + <&gcc GCC_PCIE0_AXI_S_CLK>,
>> + <&gcc GCC_PCIE0_AHB_CLK>,
>> + <&gcc GCC_PCIE0_AUX_CLK>;
>> +
>> + clock-names = "iface",
>> + "axi_m",
>> + "axi_s",
>> + "ahb",
>> + "aux";
>> + resets = <&gcc GCC_PCIE0_PIPE_ARES>,
>> + <&gcc GCC_PCIE0_SLEEP_ARES>,
>> + <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
>> + <&gcc GCC_PCIE0_AXI_MASTER_ARES>,
>> + <&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
>> + <&gcc GCC_PCIE0_AHB_ARES>,
>> + <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>;
>> + reset-names = "pipe",
>> + "sleep",
>> + "sticky",
>> + "axi_m",
>> + "axi_s",
>> + "ahb",
>> + "axi_m_sticky";
>> + status = "disabled";
>> + };
>> +
>> + pcie_phy1: phy@8e000 {
>> + compatible = "qcom,ipq8074-qmp-pcie-phy";
>> + reg = <0x8e000 0x1000>;
>> + #phy-cells = <0>;
>> + clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
>> + clock-names = "pipe_clk";
>> + clock-output-names = "pcie20_phy1_pipe_clk";
>> +
>> + resets = <&gcc GCC_PCIE1_PHY_BCR>,
>> + <&gcc GCC_PCIE1PHY_PHY_BCR>;
>> + reset-names = "phy",
>> + "common";
>> + status = "disabled";
>> + };
>> +
>> + pcie1: pci@10000000 {
>> + compatible = "qcom,pcie-ipq8074";
>> + reg = <0x10000000 0xf1d
>> + 0x10000f20 0xa8
>> + 0x88000 0x2000
>> + 0x10100000 0x1000>;
>> + reg-names = "dbi", "elbi", "parf", "config";
>> + device_type = "pci";
>> + linux,pci-domain = <1>;
>> + bus-range = <0x00 0xff>;
>> + num-lanes = <1>;
>> + #address-cells = <3>;
>> + #size-cells = <2>;
>> +
>> + phys = <&pcie_phy1>;
>> + phy-names = "pciephy";
>> +
>> + ranges = <0x81000000 0 0x10200000 0x10200000
>> + 0 0x100000 /* downstream I/O */
>> + 0x82000000 0 0x10300000 0x10300000
>> + 0 0xd00000>; /* non-prefetchable memory */
>> +
>> + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
>> + interrupt-names = "msi";
>> + #interrupt-cells = <1>;
>> + interrupt-map-mask = <0 0 0 0x7>;
>> + interrupt-map = <0 0 0 1 &intc 0 142
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_a */
>> + <0 0 0 2 &intc 0 143
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_b */
>> + <0 0 0 3 &intc 0 144
>> + IRQ_TYPE_LEVEL_HIGH>, /* int_c */
>> + <0 0 0 4 &intc 0 145
>> + IRQ_TYPE_LEVEL_HIGH>; /* int_d */
>> +
>> + clocks = <&gcc GCC_SYS_NOC_PCIE1_AXI_CLK>,
>> + <&gcc GCC_PCIE1_AXI_M_CLK>,
>> + <&gcc GCC_PCIE1_AXI_S_CLK>,
>> + <&gcc GCC_PCIE1_AHB_CLK>,
>> + <&gcc GCC_PCIE1_AUX_CLK>;
>> + clock-names = "iface",
>> + "axi_m",
>> + "axi_s",
>> + "ahb",
>> + "aux";
>> + resets = <&gcc GCC_PCIE1_PIPE_ARES>,
>> + <&gcc GCC_PCIE1_SLEEP_ARES>,
>> + <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
>> + <&gcc GCC_PCIE1_AXI_MASTER_ARES>,
>> + <&gcc GCC_PCIE1_AXI_SLAVE_ARES>,
>> + <&gcc GCC_PCIE1_AHB_ARES>,
>> + <&gcc GCC_PCIE1_AXI_MASTER_STICKY_ARES>;
>> + reset-names = "pipe",
>> + "sleep",
>> + "sticky",
>> + "axi_m",
>> + "axi_s",
>> + "ahb",
>> + "axi_m_sticky";
>> + status = "disabled";
>> + };
>> };
>>
>> cpus {
>> --
>> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
>>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
--
"QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
