On Tue, Mar 20, 2018 at 02:43:33PM +0200, Laurent Pinchart wrote:
> Hi Jacopo,
>
> (CC'ing Rob)
>
> Thank you for the patch.
>
> On Friday, 16 March 2018 17:16:37 EET Jacopo Mondi wrote:
> > Document Thine THC63LVD1024 LVDS decoder device tree bindings.
> >
> > Signed-off-by: Jacopo Mondi <jacopo+renesas@xxxxxxxxxx>
> > Reviewed-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
> > Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
> > ---
> > .../bindings/display/bridge/thine,thc63lvd1024.txt | 66 +++++++++++++++++++
> > 1 file changed, 66 insertions(+)
> > create mode 100644
> > Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
> >
> > diff --git
> > a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
> > b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
> > new file mode 100644
> > index 0000000..8225c6a
> > --- /dev/null
> > +++
> > b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt
> > @@ -0,0 +1,66 @@
> > +Thine Electronics THC63LVD1024 LVDS decoder
> > +-------------------------------------------
> > +
> > +The THC63LVD1024 is a dual link LVDS receiver designed to convert LVDS
> > streams
> > +to parallel data outputs. The chip supports single/dual input/output modes,
> > +handling up to two two input LVDS stream and up to two digital CMOS/TTL
> > outputs.
> > +
> > +Single or dual operation modes, output data mapping and DDR output modes
> > are
> > +configured through input signals and the chip does not expose any control
> > bus.
> > +
> > +Required properties:
> > +- compatible: Shall be "thine,thc63lvd1024"
> > +
> > +Optional properties:
> > +- vcc-supply: Power supply for TTL output and digital circuitry
> > +- cvcc-supply: Power supply for TTL CLOCKOUT signal
> > +- lvcc-supply: Power supply for LVDS inputs
> > +- pvcc-supply: Power supply for PLL circuitry
>
> As explained in a comment to one of the previous versions of this series, I'm
> tempted to make vcc-supply mandatory and drop the three other power supplies
> for now, as I believe there's very little chance they will be connected to
> separately controllable regulators (all supplies use the same voltage). In the
> very unlikely event that this occurs in design we need to support in the
> future, the cvcc, lvcc and pvcc supplies can be added later as optional
> without breaking backward compatibility.
I'm okay with that.
> Apart from that,
>
> Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
>
> > +- pdwn-gpios: Power down GPIO signal. Active low
powerdown-gpios is the semi-standard name.
> > +- oe-gpios: Output enable GPIO signal. Active high
> > +
> > +The THC63LVD1024 video port connections are modeled according
> > +to OF graph bindings specified by
> > Documentation/devicetree/bindings/graph.txt
> > +
> > +Required video port nodes:
> > +- Port@0: First LVDS input port
> > +- Port@2: First digital CMOS/TTL parallel output
s/Port/port/
> > +
> > +Optional video port nodes:
> > +- Port@1: Second LVDS input port
> > +- Port@3: Second digital CMOS/TTL parallel output
> > +
> > +Example:
> > +--------
> > +
> > + thc63lvd1024: lvds-decoder {
> > + compatible = "thine,thc63lvd1024";
> > +
> > + vcc-supply = <®_lvds_vcc>;
> > + lvcc-supply = <®_lvds_lvcc>;
> > +
> > + pdwn-gpio = <&gpio4 15 GPIO_ACTIVE_LOW>;
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > +
> > + lvds_dec_in_0: endpoint {
> > + remote-endpoint = <&lvds_out>;
> > + };
> > + };
> > +
> > + port@2{
> > + reg = <2>;
> > +
> > + lvds_dec_out_2: endpoint {
> > + remote-endpoint = <&adv7511_in>;
> > + };
> > +
> > + };
> > +
> > + };
> > + };
>
> --
> Regards,
>
> Laurent Pinchart
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
