Re: [PATCH v5 2/3] dt-bindings: net: bluetooth: Add qualcomm-bluetooth

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Marcel,

On 20/03/2018 16:58, Marcel Holtmann wrote:
Hi Thierry,

Add binding document for serial bluetooth chips using Qualcomm protocol.

Signed-off-by: Thierry Escande <thierry.escande@xxxxxxxxxx>
---

v5:
- Rename 'bt-disable-n' gpio as 'enable'

v4:
- Move bt-disable-n-gpios to required properties section
- Add clocks and pinctrl-0 as required properties

v3: no change
v2: no change

.../devicetree/bindings/net/qualcomm-bluetooth.txt | 34 ++++++++++++++++++++++
1 file changed, 34 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt

diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
new file mode 100644
index 000000000000..bbc2973634b2
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt
@@ -0,0 +1,34 @@
+Qualcomm Bluetooth Chips
+---------------------
+
+This documents the binding structure and common properties for serial
+attached Qualcomm devices.
+
+Serial attached Qualcomm devices shall be a child node of the host UART
+device the slave device is attached to.
+
+Required properties:
+ - compatible: should contain one of the following:
+   * "qcom,qca6174-bt"
+ - enable-gpios: gpio specifier used to enable chip
+ - pinctrl-0: pin phandle for bt_en gpio
+ - clocks: clock phandle for SUSCLK_32KHZ

if I compare this with broadcom-bluetooth.txt or ti-bluetooth.txt then besides compatible, everything else is optional. The nokia-bluetooth.txt has everything required, but that is also a really specific platform.

Can we be less restrictive for a QCA general purpose chip?
Ok. To me, at least the enable gpio seems required.


+
+Example:
+
+serial@7570000 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&blsp1_uart1_default>;
+	pinctrl-1 = <&blsp1_uart1_sleep>;
+
+	bluetooth {
+		compatible = "qcom,qca6174-bt";
+
+		enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_en_pin_a>;

This one I do not understand and you might want to shed some light into why this is done that way.
Sure. It reclaims this gpio pin for this device. Will add it to the documentation.


+
+		clocks = <&divclk4>;

No clock-names?
No need for a name as there is only one clk obtained by passing a NULL id to devm_gpiod_get().

Regards,
Thierry


Regards

Marcel

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux