[PATCH v2] ARM: dts: qcom: Add apq8064 Dragon Board 600c support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>

This patch add support to DB600c board, which is another
96boards based on Qualcomm APQ8064 SoC.

Support for USB, HDMI, PCIe, I2C, SPI, eMMC, microSD card, LEDs
device tree nodes is added in this patch.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
---
Changes since v1:
	- added chosen node with stdout, suggested by Stephen Boyd
	- removed spi flash node and gpio22 pinconf, as its not required in this patch.
	- removed extra comment lines and fix a node name, spotted by Stephen Boyd.

 arch/arm/boot/dts/Makefile                |   1 +
 arch/arm/boot/dts/qcom-apq8064-db600c.dts | 530 ++++++++++++++++++++++++++++++
 2 files changed, 531 insertions(+)
 create mode 100644 arch/arm/boot/dts/qcom-apq8064-db600c.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ade7a38543dc..940db57e57b8 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -743,6 +743,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-apq8064-ifc6410.dtb \
 	qcom-apq8064-sony-xperia-yuga.dtb \
 	qcom-apq8064-asus-nexus7-flo.dtb \
+	qcom-apq8064-db600c.dtb \
 	qcom-apq8074-dragonboard.dtb \
 	qcom-apq8084-ifc6540.dtb \
 	qcom-apq8084-mtp.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8064-db600c.dts b/arch/arm/boot/dts/qcom-apq8064-db600c.dts
new file mode 100644
index 000000000000..50151ef6e912
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8064-db600c.dts
@@ -0,0 +1,530 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-apq8064-v2.0.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+
+/ {
+	model = "Qualcomm Technologies, Inc. DB600c";
+	compatible = "arrow,apq8064-db600c", "qcom,apq8064";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+		serial1 = &gsbi1_serial;
+		i2c0 = &gsbi2_i2c;
+		i2c1 = &gsbi3_i2c;
+		i2c2 = &gsbi4_i2c;
+		i2c3 = &gsbi7_i2c;
+		spi0 = &gsbi5_spi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		vph: regulator-fixed {
+			compatible = "regulator-fixed";
+			regulator-min-microvolt = <4500000>;
+			regulator-max-microvolt = <4500000>;
+			regulator-name = "VPH";
+			regulator-type = "voltage";
+			regulator-boot-on;
+		};
+
+		/* on board fixed 3.3v supply */
+		vcc3v3: vcc3v3 {
+			compatible = "regulator-fixed";
+			regulator-name = "VCC3V3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&hdmi_out>;
+			};
+		};
+	};
+
+	soc {
+		pinctrl@800000 {
+			card_detect: card_detect {
+				mux {
+					pins = "gpio26";
+					function = "gpio";
+					bias-disable;
+				};
+			};
+
+			user_leds: user-leds {
+				mux {
+					pins = "gpio6", "gpio7", "gpio35", "gpio86";
+					function = "gpio";
+				};
+		
+				conf {
+					pins = "gpio6", "gpio7", "gpio35", "gpio86";
+					function = "gpio";
+					output-low;
+				};
+			};
+		
+			i2c1 {
+				pinconf {
+					drive-strength = <8>;
+				};
+			};
+		
+			i2c2 {
+				pinconf {
+					drive-strength = <8>;
+				};
+			};
+		
+			i2c3 {
+				pinconf {
+					drive-strength = <8>;
+				};
+			};
+			
+			i2c4 {
+				pinconf {
+					drive-strength = <8>;
+				};
+			};
+		
+			i2c5 {
+				pinconf {
+					drive-strength = <8>;
+				};
+			};
+		
+			i2c6 {
+				pinconf {
+					drive-strength = <8>;
+				};
+			};
+		
+			i2c7 {
+				pinconf {
+					drive-strength = <8>;
+				};
+			};
+
+			i2c1 {
+				pinconf {
+					drive-strength = <8>;
+				};
+			};
+		
+			spi5_default {
+				pinconf {
+					drive-strength = <8>;
+				};
+		
+				pinconf_cs {
+					drive-strength = <8>;
+				};
+			};
+		};
+
+		qcom,ssbi@500000 {
+			pmic@0 {
+				mpps@50 {
+					pcie_perst: pcie-perst {
+						pinconf {
+							pins = "mpp1";
+							function = "digital";
+							power-source = <PM8921_MPP_S4>;
+							output-low;
+						};
+					};
+			
+					mpp_leds: mpp-leds {
+						pinconf {
+							pins = "mpp7", "mpp8", "mpp9", "mpp10",	"mpp11", "mpp12";
+							function = "digital";
+							power-source = <PM8921_MPP_VPH>;
+							drive-strength = <12>;
+							output-high;
+						};
+					};
+				};
+			};
+		};
+
+		rpm@108000 {
+			regulators {
+				vdd_s1-supply = <&vph>;
+				vdd_s2-supply = <&vph>;
+				vdd_s3-supply = <&vph>;
+				vdd_s4-supply = <&vph>;
+				vdd_s5-supply = <&vph>;
+				vdd_s6-supply = <&vph>;
+				vdd_s7-supply = <&vph>;
+
+				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+				vdd_l3_l15_l17-supply = <&vph>;
+				vdd_l4_l14-supply = <&vph>;
+				vdd_l5_l8_l16-supply = <&vph>;
+				vdd_l6_l7-supply = <&vph>;
+				vdd_l9_l11-supply = <&vph>;
+				vdd_l10_l22-supply = <&vph>;
+				vdd_l21_l23_l29-supply = <&vph>;
+
+				vdd_l24-supply = <&pm8921_s1>;
+				vdd_l25-supply = <&pm8921_s1>;
+				vdd_l26-supply = <&pm8921_s7>;
+				vdd_l27-supply = <&pm8921_s7>;
+				vdd_l28-supply = <&pm8921_s7>;
+
+				vin_lvs1_3_6-supply = <&pm8921_s4>;
+				vin_lvs2-supply = <&pm8921_s1>;
+				vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+				s1 {
+					regulator-always-on;
+					regulator-min-microvolt = <1225000>;
+					regulator-max-microvolt = <1225000>;
+					qcom,switch-mode-frequency = <3200000>;
+					bias-pull-down;
+				};
+
+				s2 {
+					regulator-min-microvolt = <1300000>;
+					regulator-max-microvolt = <1300000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+					regulator-always-on;
+				};
+
+				s3 {
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1400000>;
+					qcom,switch-mode-frequency = <4800000>;
+				};
+
+				s4 {
+					regulator-min-microvolt	= <1800000>;
+					regulator-max-microvolt	= <1800000>;
+					qcom,switch-mode-frequency = <1600000>;
+					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+					bias-pull-down;
+					regulator-always-on;
+				};
+
+				s7 {
+					regulator-min-microvolt = <1300000>;
+					regulator-max-microvolt = <1300000>;
+					qcom,switch-mode-frequency = <3200000>;
+				 };
+
+				l3 {
+					regulator-min-microvolt = <3050000>;
+					regulator-max-microvolt = <3300000>;
+					bias-pull-down;
+				};
+
+				l4 {
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+
+				l5 {
+					regulator-min-microvolt = <2750000>;
+					regulator-max-microvolt = <3000000>;
+					bias-pull-down;
+					regulator-boot-on;
+					regulator-always-on;
+				};
+
+				l6 {
+					regulator-min-microvolt = <2950000>;
+					regulator-max-microvolt = <2950000>;
+					bias-pull-down;
+				};
+
+				l7 {
+					regulator-min-microvolt = <2950000>;
+					regulator-max-microvolt = <2950000>;
+					regulator-boot-on;
+					regulator-always-on;
+				};
+
+				/**
+				 * 1.8v required on LS expansion
+				 * for mezzanine boards
+				 */
+				l15 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				l23 {
+					regulator-min-microvolt = <1700000>;
+					regulator-max-microvolt = <1900000>;
+					bias-pull-down;
+				};
+
+				l26 {
+					regulator-min-microvolt = < 375000>;
+					regulator-max-microvolt = <1050000>;
+					bias-pull-down;
+				};
+
+				lvs6 {
+					bias-pull-down;
+				};
+
+				lvs7 {
+					bias-pull-down;
+				};
+			};
+		};
+
+		gsbi@12440000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_UART_W_FC>;
+			serial@12450000 {
+				label = "LS-UART1";
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&gsbi1_uart_4pins>;
+			};
+		};
+
+		gsbi@12480000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_I2C>;
+			i2c@124a0000 {
+				/* On Low speed expansion and Sensors */
+				label = "LS-I2C0";
+				status = "okay";
+			};
+		};
+
+		gsbi@16200000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_I2C>;
+			i2c@16280000 {
+			/* On Low speed expansion */
+				status = "okay";
+				label = "LS-I2C1";
+				clock-frequency = <200000>;
+				eeprom@52 {
+					compatible = "atmel,24c128";
+					reg = <0x52>;
+					pagesize = <64>;
+				};
+			};
+		};
+
+		gsbi@16300000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_I2C>;
+			i2c@16380000 {
+				/* On High speed expansion */
+				label = "HS-CAM-I2C3";
+				status = "okay";
+			};
+		};
+
+		gsbi@1a200000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_SPI>;
+			spi@1a280000 {
+				/* On Low speed expansion */
+				label = "LS-SPI0";
+				status = "okay";
+			};
+		};
+
+		gsbi@16500000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_UART_W_FC>;
+			serial@1654000 {
+				label = "BT-UART";
+				status = "okay";
+				pinctrl-name = "default";
+				pinctrl-0 = <&gsbi6_uart_4pins>;
+			};
+		};
+
+
+		/* DEBUG UART  */
+		gsbi@16600000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+			serial@16640000 {
+				label = "LS-UART0";
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&gsbi7_uart_2pins>;
+
+			};
+
+			i2c@16680000 {
+				/* On High speed expansion */
+				status = "okay";
+				label = "HS-CAM-I2C2";
+			};
+		};
+
+		leds {
+			pinctrl-names = "default";
+			pinctrl-0 = <&user_leds>, <&mpp_leds>;
+
+			compatible = "gpio-leds";
+
+			user-led0 {
+				label = "user0-led";
+				gpios = <&pm8921_mpps 9 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "heartbeat";
+				default-state = "off";
+			};
+
+			user-led1 {
+				label = "user1-led";
+				gpios = <&pm8921_mpps 10 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "mmc0";
+				default-state = "off";
+			};
+
+			user-led2 {
+				label = "user2-led";
+				gpios = <&pm8921_mpps 11 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "mmc1";
+				default-state = "off";
+			};
+
+			user-led3 {
+				label = "user3-led";
+				gpios = <&pm8921_mpps 12 GPIO_ACTIVE_HIGH>;
+				linux,default-trigger = "none";
+				default-state = "off";
+			};
+
+			wifi-led {
+				label = "WiFi-led";
+				gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+				linux,default-trigger = "none";
+			};
+
+			bt-led {
+				label = "BT-led";
+				gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+				linux,default-trigger = "none";
+			};
+		};
+
+		pci@1b500000 {
+			status = "okay";
+			vdda-supply = <&pm8921_s3>;
+			vdda_phy-supply = <&pm8921_lvs6>;
+			vdda_refclk-supply = <&vcc3v3>;
+			pinctrl-0 = <&pcie_perst>;
+			pinctrl-names = "default";
+			perst-gpio = <&pm8921_mpps 1 GPIO_ACTIVE_LOW>;
+		};
+
+		/* OTG */
+		usb@12500000 {
+			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
+		};
+
+		usb@12520000 {
+			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
+		};
+
+		usb@12530000 {
+			status = "okay";
+			dr_mode = "host";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l23>;
+				};
+			};
+		};
+
+		amba {
+			/* eMMC */
+			sdcc1: sdcc@12400000 {
+				status = "okay";
+				vmmc-supply = <&pm8921_l5>;
+				vqmmc-supply = <&pm8921_s4>;
+			};
+
+			/* External micro SD card */
+			sdcc3: sdcc@12180000 {
+				status = "okay";
+				vmmc-supply = <&pm8921_l6>;
+				vqmmc-supply = <&pm8921_l7>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&sdcc3_pins &card_detect>;
+				cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+			};
+		};
+
+		hdmi-tx@4a00000 {
+			status = "okay";
+			core-vdda-supply = <&pm8921_hdmi_switch>;
+			hdmi-mux-supply = <&vcc3v3>;
+
+			hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
+
+			ports {
+				port@1 {
+					endpoint {
+						remote-endpoint = <&hdmi_con>;
+					};
+				};
+			};
+		};
+
+		hdmi-phy@4a00400 {
+			status = "okay";
+			core-vdda-supply = <&pm8921_hdmi_switch>;
+		};
+
+		mdp@5100000 {
+			status = "okay";
+
+			ports {
+				port@3 {
+					endpoint {
+						remote-endpoint = <&hdmi_in>;
+					};
+				};
+			};
+		};
+	};
+};
-- 
2.16.2

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux