On 2018-03-16 15:08, Sricharan R wrote:
The driver/phy support for ipq8074 is available now.
So enabling the nodes in DT.
Signed-off-by: Sricharan R <sricharan@xxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/ipq8074.dtsi | 157
+++++++++++++++++++++++++++++++++-
1 file changed, 156 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index 806fc56..7562650 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -24,7 +24,7 @@
ranges = <0 0 0 0xffffffff>;
compatible = "simple-bus";
- pinctrl@1000000 {
+ tlmm: pinctrl@1000000 {
compatible = "qcom,ipq8074-pinctrl";
reg = <0x1000000 0x300000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
@@ -229,6 +229,161 @@
dma-names = "tx", "rx", "cmd";
status = "disabled";
};
+
+ pcie_phy0: phy@86000 {
+ compatible = "qcom,ipq8074-qmp-pcie-phy";
+ reg = <0x86000 0x1000>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
+ clock-names = "pipe_clk";
+ clock-output-names = "pcie20_phy0_pipe_clk";
+
+ resets = <&gcc GCC_PCIE0_PHY_BCR>,
+ <&gcc GCC_PCIE0PHY_PHY_BCR>;
+ reset-names = "phy",
+ "common";
+ status = "disabled";
+ };
+
+ pcie0: pci@20000000 {
+ compatible = "qcom,pcie-ipq8074";
+ reg = <0x20000000 0xf1d
+ 0x20000F20 0xa8
s/0x20000F20/0x20000f20
+ 0x80000 0x2000
+ 0x20100000 0x1000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ phys = <&pcie_phy0>;
+ phy-names = "pciephy";
+
+ ranges = <0x81000000 0 0x20200000 0x20200000
+ 0 0x00100000 /* downstream I/O */
we can remove trailing zeros from address.
s/0x00100000/0x100000
+ 0x82000000 0 0x20300000 0x20300000
+ 0 0x00d00000>; /* non-prefetchable memory */
s/0x00d00000/0xd00000
Same changes are for PCIE1 also.
With that.
Reviewed-by: Abhishek Sahu <absahu@xxxxxxxxxxxxxx>
+
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 75
+ IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 78
+ IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 79
+ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 83
+ IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
+ <&gcc GCC_PCIE0_AXI_M_CLK>,
+ <&gcc GCC_PCIE0_AXI_S_CLK>,
+ <&gcc GCC_PCIE0_AHB_CLK>,
+ <&gcc GCC_PCIE0_AUX_CLK>;
+
+ clock-names = "iface",
+ "axi_m",
+ "axi_s",
+ "ahb",
+ "aux";
+ resets = <&gcc GCC_PCIE0_PIPE_ARES>,
+ <&gcc GCC_PCIE0_SLEEP_ARES>,
+ <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE0_AXI_MASTER_ARES>,
+ <&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
+ <&gcc GCC_PCIE0_AHB_ARES>,
+ <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>;
+ reset-names = "pipe",
+ "sleep",
+ "sticky",
+ "axi_m",
+ "axi_s",
+ "ahb",
+ "axi_m_sticky";
+ status = "disabled";
+ };
+
+ pcie_phy1: phy@8e000 {
+ compatible = "qcom,ipq8074-qmp-pcie-phy";
+ reg = <0x8e000 0x1000>;
+ #phy-cells = <0>;
+ clocks = <&gcc GCC_PCIE1_PIPE_CLK>;
+ clock-names = "pipe_clk";
+ clock-output-names = "pcie20_phy1_pipe_clk";
+
+ resets = <&gcc GCC_PCIE1_PHY_BCR>,
+ <&gcc GCC_PCIE1PHY_PHY_BCR>;
+ reset-names = "phy",
+ "common";
+ status = "disabled";
+ };
+
+ pcie1: pci@10000000 {
+ compatible = "qcom,pcie-ipq8074";
+ reg = <0x10000000 0xf1d
+ 0x10000F20 0xa8
+ 0x88000 0x2000
+ 0x10100000 0x1000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <1>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ phys = <&pcie_phy1>;
+ phy-names = "pciephy";
+
+ ranges = <0x81000000 0 0x10200000 0x10200000
+ 0 0x00100000 /* downstream I/O */
+ 0x82000000 0 0x10300000 0x10300000
+ 0 0x00d00000>; /* non-prefetchable memory */
+
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc 0 142
+ IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc 0 143
+ IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc 0 144
+ IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc 0 145
+ IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+ clocks = <&gcc GCC_SYS_NOC_PCIE1_AXI_CLK>,
+ <&gcc GCC_PCIE1_AXI_M_CLK>,
+ <&gcc GCC_PCIE1_AXI_S_CLK>,
+ <&gcc GCC_PCIE1_AHB_CLK>,
+ <&gcc GCC_PCIE1_AUX_CLK>;
+ clock-names = "iface",
+ "axi_m",
+ "axi_s",
+ "ahb",
+ "aux";
+ resets = <&gcc GCC_PCIE1_PIPE_ARES>,
+ <&gcc GCC_PCIE1_SLEEP_ARES>,
+ <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE1_AXI_MASTER_ARES>,
+ <&gcc GCC_PCIE1_AXI_SLAVE_ARES>,
+ <&gcc GCC_PCIE1_AHB_ARES>,
+ <&gcc GCC_PCIE1_AXI_MASTER_STICKY_ARES>;
+ reset-names = "pipe",
+ "sleep",
+ "sticky",
+ "axi_m",
+ "axi_s",
+ "ahb",
+ "axi_m_sticky";
+ status = "disabled";
+ };
};
cpus {
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
