On Fri, Mar 02, 2018 at 01:11:34PM +0100, Philipp Rossak wrote: > On 13.02.2018 13:29, Philipp Rossak wrote: > > This patch series adds support for the sunxi A83T ir module and enhances > > the sunxi-ir driver. Right now the base clock frequency for the ir driver > > is a hard coded define and is set to 8 MHz. > > This works for the most common ir receivers. On the Sinovoip Bananapi M3 > > the ir receiver needs, a 3 MHz base clock frequency to work without > > problems with this driver. > > > > This patch series adds support for an optinal property that makes it able > > to override the default base clock frequency and enables the ir interface > > on the a83t and the Bananapi M3. > > > > changes since v4: > > * rename cir pin from cir_pins to r_cir_pin > > * drop unit-adress from r_cir_pin > > * add a83t compatible to the cir node > > * move muxing options to dtsi > > * rename cir label and reorder it in the bananpim3.dts file > > > > changes since v3: > > * collecting all acks & reviewd by > > * fixed typos > > > > changes since v2: > > * reorder cir pin (alphabetical) > > * fix typo in documentation > > > > changes since v1: > > * fix typos, reword Documentation > > * initialize 'b_clk_freq' to 'SUNXI_IR_BASE_CLK' & remove if statement > > * change dev_info() to dev_dbg() > > * change naming to cir* in dts/dtsi > > * Added acked Ackedi-by to related patch > > * use whole memory block instead of registers needed + fix for h3/h5 > > > > changes since rfc: > > * The property is now optinal. If the property is not available in > > the dtb the driver uses the default base clock frequency. > > * the driver prints out the the selected base clock frequency. > > * changed devicetree property from base-clk-frequency to clock-frequency > > > > Regards, > > Philipp > > > > Philipp Rossak (6): > > media: rc: update sunxi-ir driver to get base clock frequency from > > devicetree > > media: dt: bindings: Update binding documentation for sunxi IR > > controller > > arm: dts: sun8i: a83t: Add the cir pin for the A83T > > arm: dts: sun8i: a83t: Add support for the cir interface > > arm: dts: sun8i: a83t: bananapi-m3: Enable IR controller > > arm: dts: sun8i: h3-h5: ir register size should be the whole memory > > block > > > > Documentation/devicetree/bindings/media/sunxi-ir.txt | 3 +++ > > arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 5 +++++ > > arch/arm/boot/dts/sun8i-a83t.dtsi | 18 ++++++++++++++++++ > > arch/arm/boot/dts/sunxi-h3-h5.dtsi | 2 +- > > drivers/media/rc/sunxi-cir.c | 19 +++++++++++-------- > > 5 files changed, 38 insertions(+), 9 deletions(-) > > > > I talked yesterday with Maxime about this patch series. And he told me if > the first to patches got merged, he will apply the dts patches to the sunxi > tree. > > Sean, can you merge the first two patches through the rc-core? Sure, no problem. Thanks Sean -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
