This patch adds support for configuring the port multiplexer hardware
which resides in front of the GENET Ethernet MAC controller. This allows
us to support:
- internal PHYs (using drivers/net/phy/bcm7xxx.c)
- MoCA PHYs which are an entirely separate hardware block not covered
here
- external PHYs and switches
Note that MoCA and switches are currently supported using the emulated
"fixed PHY" driver.
Signed-off-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
---
Changes in v5:
- respin due to the CONFIG_OF depdency fix
Changes since v3:
- respin due to the Kconfig dependency fix
Changes since v2:
- remove the need to parse the 'max-speed' or 'fixed-link' properties to know
the PHY configured speed
- re-order MDIO bus probing to perform port multiplexer configuration after
probing the PHYs, simplifying logic
- check that the MDIO bus node compatible string matches our major version as
pointed out by Mark
Changes since v1:
- fixed MDIO crash/warning when Device Tree probing fails
- removed the use of priv->phy_type and use priv->phy_interface
directly
drivers/net/ethernet/broadcom/genet/bcmmii.c | 464 +++++++++++++++++++++++++++
1 file changed, 464 insertions(+)
create mode 100644 drivers/net/ethernet/broadcom/genet/bcmmii.c
diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c
new file mode 100644
index 0000000..4608673
--- /dev/null
+++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
@@ -0,0 +1,464 @@
+/*
+ * Broadcom GENET MDIO routines
+ *
+ * Copyright (c) 2014 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+
+#include <linux/types.h>
+#include <linux/delay.h>
+#include <linux/wait.h>
+#include <linux/mii.h>
+#include <linux/ethtool.h>
+#include <linux/bitops.h>
+#include <linux/netdevice.h>
+#include <linux/platform_device.h>
+#include <linux/phy.h>
+#include <linux/phy_fixed.h>
+#include <linux/brcmphy.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+#include <linux/of_mdio.h>
+
+#include "bcmgenet.h"
+
+/* read a value from the MII */
+static int bcmgenet_mii_read(struct mii_bus *bus, int phy_id, int location)
+{
+ int ret;
+ struct net_device *dev = bus->priv;
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+ u32 reg;
+
+ bcmgenet_umac_writel(priv, (MDIO_RD | (phy_id << MDIO_PMD_SHIFT) |
+ (location << MDIO_REG_SHIFT)), UMAC_MDIO_CMD);
+ /* Start MDIO transaction*/
+ reg = bcmgenet_umac_readl(priv, UMAC_MDIO_CMD);
+ reg |= MDIO_START_BUSY;
+ bcmgenet_umac_writel(priv, reg, UMAC_MDIO_CMD);
+ wait_event_timeout(priv->wq,
+ !(bcmgenet_umac_readl(priv, UMAC_MDIO_CMD)
+ & MDIO_START_BUSY),
+ HZ / 100);
+ ret = bcmgenet_umac_readl(priv, UMAC_MDIO_CMD);
+
+ if (ret & MDIO_READ_FAIL)
+ return -EIO;
+
+ return ret & 0xffff;
+}
+
+/* write a value to the MII */
+static int bcmgenet_mii_write(struct mii_bus *bus, int phy_id,
+ int location, u16 val)
+{
+ struct net_device *dev = bus->priv;
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+ u32 reg;
+
+ bcmgenet_umac_writel(priv, (MDIO_WR | (phy_id << MDIO_PMD_SHIFT) |
+ (location << MDIO_REG_SHIFT) | (0xffff & val)),
+ UMAC_MDIO_CMD);
+ reg = bcmgenet_umac_readl(priv, UMAC_MDIO_CMD);
+ reg |= MDIO_START_BUSY;
+ bcmgenet_umac_writel(priv, reg, UMAC_MDIO_CMD);
+ wait_event_timeout(priv->wq,
+ !(bcmgenet_umac_readl(priv, UMAC_MDIO_CMD) &
+ MDIO_START_BUSY),
+ HZ / 100);
+
+ return 0;
+}
+
+/* setup netdev link state when PHY link status change and
+ * update UMAC and RGMII block when link up
+ */
+static void bcmgenet_mii_setup(struct net_device *dev)
+{
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+ struct phy_device *phydev = priv->phydev;
+ u32 reg, cmd_bits = 0;
+ unsigned int status_changed = 0;
+
+ if (priv->old_link != phydev->link) {
+ status_changed = 1;
+ priv->old_link = phydev->link;
+ }
+
+ if (phydev->link) {
+ /* program UMAC and RGMII block based on established link
+ * speed, pause, and duplex.
+ * the speed set in umac->cmd tell RGMII block which clock
+ * 25MHz(100Mbps)/125MHz(1Gbps) to use for transmit.
+ * receive clock is provided by PHY.
+ */
+ reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
+ reg &= ~OOB_DISABLE;
+ reg |= RGMII_LINK;
+ bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
+
+ /* speed */
+ if (phydev->speed == SPEED_1000)
+ cmd_bits = UMAC_SPEED_1000;
+ else if (phydev->speed == SPEED_100)
+ cmd_bits = UMAC_SPEED_100;
+ else
+ cmd_bits = UMAC_SPEED_10;
+ cmd_bits <<= CMD_SPEED_SHIFT;
+
+ if (priv->old_duplex != phydev->duplex) {
+ status_changed = 1;
+ priv->old_duplex = phydev->duplex;
+ }
+
+ /* duplex */
+ if (phydev->duplex != DUPLEX_FULL)
+ cmd_bits |= CMD_HD_EN;
+
+ if (priv->old_pause != phydev->pause) {
+ status_changed = 1;
+ priv->old_pause = phydev->pause;
+ }
+
+ /* pause capability */
+ if (!phydev->pause)
+ cmd_bits |= CMD_RX_PAUSE_IGNORE | CMD_TX_PAUSE_IGNORE;
+
+ reg = bcmgenet_umac_readl(priv, UMAC_CMD);
+ reg &= ~((CMD_SPEED_MASK << CMD_SPEED_SHIFT) |
+ CMD_HD_EN |
+ CMD_RX_PAUSE_IGNORE | CMD_TX_PAUSE_IGNORE);
+ reg |= cmd_bits;
+ bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+ }
+
+ if (status_changed)
+ phy_print_status(phydev);
+}
+
+void bcmgenet_mii_reset(struct net_device *dev)
+{
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+
+ if (priv->phydev) {
+ phy_init_hw(priv->phydev);
+ phy_start_aneg(priv->phydev);
+ }
+}
+
+static void bcmgenet_ephy_power_up(struct net_device *dev)
+{
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+ u32 reg = 0;
+
+ /* EXT_GPHY_CTRL is only valid for GENETv4 and onward */
+ if (!GENET_IS_V4(priv))
+ return;
+
+ reg = bcmgenet_ext_readl(priv, EXT_GPHY_CTRL);
+ reg &= ~(EXT_CFG_IDDQ_BIAS | EXT_CFG_PWR_DOWN);
+ reg |= EXT_GPHY_RESET;
+ bcmgenet_ext_writel(priv, reg, EXT_GPHY_CTRL);
+ mdelay(2);
+
+ reg &= ~EXT_GPHY_RESET;
+ bcmgenet_ext_writel(priv, reg, EXT_GPHY_CTRL);
+ udelay(20);
+}
+
+static void bcmgenet_internal_phy_setup(struct net_device *dev)
+{
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+ u32 reg;
+
+ /* Power up EPHY */
+ bcmgenet_ephy_power_up(dev);
+ /* enable APD */
+ reg = bcmgenet_ext_readl(priv, EXT_EXT_PWR_MGMT);
+ reg |= EXT_PWR_DN_EN_LD;
+ bcmgenet_ext_writel(priv, reg, EXT_EXT_PWR_MGMT);
+ bcmgenet_mii_reset(dev);
+}
+
+static void bcmgenet_moca_phy_setup(struct bcmgenet_priv *priv)
+{
+ u32 reg;
+
+ /* Speed settings are set in bcmgenet_mii_setup() */
+ reg = bcmgenet_sys_readl(priv, SYS_PORT_CTRL);
+ reg |= LED_ACT_SOURCE_MAC;
+ bcmgenet_sys_writel(priv, reg, SYS_PORT_CTRL);
+}
+
+int bcmgenet_mii_config(struct net_device *dev)
+{
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+ struct phy_device *phydev = priv->phydev;
+ struct device *kdev = &priv->pdev->dev;
+ const char *phy_name = NULL;
+ u32 id_mode_dis = 0;
+ u32 port_ctrl;
+ u32 reg;
+
+ priv->ext_phy = !phy_is_internal(priv->phydev) &&
+ (priv->phy_interface != PHY_INTERFACE_MODE_MOCA);
+
+ if (phy_is_internal(priv->phydev))
+ priv->phy_interface = PHY_INTERFACE_MODE_NA;
+
+ switch (priv->phy_interface) {
+ case PHY_INTERFACE_MODE_NA:
+ case PHY_INTERFACE_MODE_MOCA:
+ /* Irrespective of the actually configured PHY speed (100 or
+ * 1000) GENETv4 only has an internal GPHY so we will just end
+ * up masking the Gigabit features from what we support, not
+ * switching to the EPHY
+ */
+ if (GENET_IS_V4(priv))
+ port_ctrl = PORT_MODE_INT_GPHY;
+ else
+ port_ctrl = PORT_MODE_INT_EPHY;
+
+ bcmgenet_sys_writel(priv, port_ctrl, SYS_PORT_CTRL);
+
+ if (phy_is_internal(priv->phydev)) {
+ phy_name = "internal PHY";
+ bcmgenet_internal_phy_setup(dev);
+ } else if (priv->phy_interface == PHY_INTERFACE_MODE_MOCA) {
+ phy_name = "MoCA";
+ bcmgenet_moca_phy_setup(priv);
+ }
+ break;
+
+ case PHY_INTERFACE_MODE_MII:
+ phy_name = "external MII";
+ phydev->supported &= PHY_BASIC_FEATURES;
+ bcmgenet_sys_writel(priv,
+ PORT_MODE_EXT_EPHY, SYS_PORT_CTRL);
+ break;
+
+ case PHY_INTERFACE_MODE_REVMII:
+ phy_name = "external RvMII";
+ /* of_mdiobus_register took care of reading the 'max-speed'
+ * PHY property for us, effectively limiting the PHY supported
+ * capabilities, use that knowledge to also configure the
+ * Reverse MII interface correctly.
+ */
+ if ((priv->phydev->supported & PHY_BASIC_FEATURES) ==
+ PHY_BASIC_FEATURES)
+ port_ctrl = PORT_MODE_EXT_RVMII_25;
+ else
+ port_ctrl = PORT_MODE_EXT_RVMII_50;
+ bcmgenet_sys_writel(priv, port_ctrl, SYS_PORT_CTRL);
+ break;
+
+ case PHY_INTERFACE_MODE_RGMII:
+ /* RGMII_NO_ID: TXC transitions at the same time as TXD
+ * (requires PCB or receiver-side delay)
+ * RGMII: Add 2ns delay on TXC (90 degree shift)
+ *
+ * ID is implicitly disabled for 100Mbps (RG)MII operation.
+ */
+ id_mode_dis = BIT(16);
+ /* fall through */
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ if (id_mode_dis)
+ phy_name = "external RGMII (no delay)";
+ else
+ phy_name = "external RGMII (TX delay)";
+ reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
+ reg |= RGMII_MODE_EN | id_mode_dis;
+ bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
+ bcmgenet_sys_writel(priv,
+ PORT_MODE_EXT_GPHY, SYS_PORT_CTRL);
+ break;
+ default:
+ dev_err(kdev, "unknown phy mode: %d\n", priv->phy_interface);
+ return -EINVAL;
+ }
+
+ dev_info(kdev, "configuring instance for %s\n", phy_name);
+
+ return 0;
+}
+
+static int bcmgenet_mii_probe(struct net_device *dev)
+{
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+ struct phy_device *phydev;
+ unsigned int phy_flags;
+ int ret;
+
+ if (priv->phydev) {
+ pr_info("PHY already attached\n");
+ return 0;
+ }
+
+ if (priv->phy_dn)
+ phydev = of_phy_connect(dev, priv->phy_dn,
+ bcmgenet_mii_setup, 0,
+ priv->phy_interface);
+ else
+ phydev = of_phy_connect_fixed_link(dev,
+ bcmgenet_mii_setup,
+ priv->phy_interface);
+
+ if (!phydev) {
+ pr_err("could not attach to PHY\n");
+ return -ENODEV;
+ }
+
+ priv->old_link = -1;
+ priv->old_duplex = -1;
+ priv->old_pause = -1;
+ priv->phydev = phydev;
+
+ /* Configure port multiplexer based on what the probed PHY device since
+ * reading the 'max-speed' property determines the maximum supported
+ * PHY speed which is needed for bcmgenet_mii_config() to configure
+ * things appropriately.
+ */
+ ret = bcmgenet_mii_config(dev);
+ if (ret) {
+ phy_disconnect(priv->phydev);
+ return ret;
+ }
+
+ phy_flags = PHY_BRCM_100MBPS_WAR;
+
+ /* workarounds are only needed for 100Mpbs PHYs, and
+ * never on GENET V1 hardware
+ */
+ if ((phydev->supported & PHY_GBIT_FEATURES) || GENET_IS_V1(priv))
+ phy_flags = 0;
+
+ phydev->dev_flags |= phy_flags;
+ phydev->advertising = phydev->supported;
+
+ /* The internal PHY has its link interrupts routed to the
+ * Ethernet MAC ISRs
+ */
+ if (phy_is_internal(priv->phydev))
+ priv->mii_bus->irq[phydev->addr] = PHY_IGNORE_INTERRUPT;
+ else
+ priv->mii_bus->irq[phydev->addr] = PHY_POLL;
+
+ pr_info("attached PHY at address %d [%s]\n",
+ phydev->addr, phydev->drv->name);
+
+ return 0;
+}
+
+static int bcmgenet_mii_alloc(struct bcmgenet_priv *priv)
+{
+ struct mii_bus *bus;
+
+ if (priv->mii_bus)
+ return 0;
+
+ priv->mii_bus = mdiobus_alloc();
+ if (!priv->mii_bus) {
+ pr_err("failed to allocate\n");
+ return -ENOMEM;
+ }
+
+ bus = priv->mii_bus;
+ bus->priv = priv->dev;
+ bus->name = "bcmgenet MII bus";
+ bus->parent = &priv->pdev->dev;
+ bus->read = bcmgenet_mii_read;
+ bus->write = bcmgenet_mii_write;
+ snprintf(bus->id, MII_BUS_ID_SIZE, "%s-%d",
+ priv->pdev->name, priv->pdev->id);
+
+ bus->irq = kzalloc(sizeof(int) * PHY_MAX_ADDR, GFP_KERNEL);
+ if (!bus->irq) {
+ mdiobus_free(priv->mii_bus);
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+static int bcmgenet_mii_of_init(struct bcmgenet_priv *priv)
+{
+ struct device_node *dn = priv->pdev->dev.of_node;
+ struct device *kdev = &priv->pdev->dev;
+ struct device_node *mdio_dn;
+ char *compat;
+ int ret;
+
+ compat = kasprintf(GFP_KERNEL, "brcm,genet-mdio-v%d", priv->version);
+ if (!compat)
+ return -ENOMEM;
+
+ mdio_dn = of_find_compatible_node(dn, NULL, compat);
+ kfree(compat);
+ if (!mdio_dn) {
+ dev_err(kdev, "unable to find MDIO bus node\n");
+ return -ENODEV;
+ }
+
+ ret = of_mdiobus_register(priv->mii_bus, mdio_dn);
+ if (ret) {
+ dev_err(kdev, "failed to register MDIO bus\n");
+ return ret;
+ }
+
+ /* Fetch the PHY phandle */
+ priv->phy_dn = of_parse_phandle(dn, "phy-handle", 0);
+
+ /* Get the link mode */
+ priv->phy_interface = of_get_phy_mode(dn);
+
+ return 0;
+}
+
+int bcmgenet_mii_init(struct net_device *dev)
+{
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+ int ret;
+
+ ret = bcmgenet_mii_alloc(priv);
+ if (ret)
+ return ret;
+
+ ret = bcmgenet_mii_of_init(priv);
+ if (ret)
+ goto out_free;
+
+ ret = bcmgenet_mii_probe(dev);
+ if (ret)
+ goto out;
+
+ return 0;
+
+out:
+ mdiobus_unregister(priv->mii_bus);
+out_free:
+ kfree(priv->mii_bus->irq);
+ mdiobus_free(priv->mii_bus);
+ return ret;
+}
+
+void bcmgenet_mii_exit(struct net_device *dev)
+{
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+
+ mdiobus_unregister(priv->mii_bus);
+ kfree(priv->mii_bus->irq);
+ mdiobus_free(priv->mii_bus);
+}
--
1.8.3.2
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
