On Tue, Feb 20, 2018 at 01:51:28PM +0100, Geert Uytterhoeven wrote: > On Mon, Feb 12, 2018 at 6:44 PM, Fabrizio Castro > <fabrizio.castro@xxxxxxxxxxxxxx> wrote: > > this series has been around for some time as RFC, and it has collected > > useful comments from the community along the way. > > The solution proposed by this patch set works for most R-Car Gen2 and > > RZ/G1 devices, but not all of them. We now know that for some R-Car > > Gen2 early revisions there is no proper software fix. Anyway, no > > product has been built around early revisions, but development boards > > mounting early revisions (basically prototypes) are still out there. > > As a result, this series isn't enabling the internal watchdog on R-Car > > Gen2 boards, developers may enable it in board specific device trees > > if needed. > > This series has been tested by me on the iwg20d, iwg22d, Lager, Alt, > > and Koelsch boards. > > > > The problem > > =========== > > To deal with SMP on R-Car Gen2 and RZ/G1, we install a reset vector > > to ICRAM1 and we program the [S]BAR registers so that when we turn ON > > the non-boot CPUs they are redirected to the reset vector installed by > > Linux in ICRAM1, and eventually they continue the execution to RAM, > > where the SMP bring-up code will take care of the rest. > > The content of the [S]BAR registers survives a watchdog triggered reset, > > and as such after the watchdog fires the boot core will try and execute > > the SMP bring-up code instead of jumping to the bootrom code. > > > > The fix > > ======= > > The main strategy for the solution is to let the reset vector decide > > if it needs to jump to shmobile_boot_fn or to the bootrom code. > > In a watchdog triggered reset scenario, since the [S]BAR registers keep > > their values, the boot CPU will jump into the newly designed reset > > vector, the assembly routine will eventually test WOVF (a bit in register > > RWTCSRA that indicates if the watchdog counter has overflown, the value > > of this bit gets retained in this scenario), and jump to the bootrom code > > which will in turn load up the bootloader, etc. > > When bringing up SMP or using CPU hotplug, the reset vector will jump > > to shmobile_boot_fn instead. > > > > Thank you All for your help. > > > > Best regards, > > > > Fabrizio Castro (26): > > ARM: shmobile: Add watchdog support > > ARM: dts: r8a7743: Adjust SMP routine size > > ARM: dts: r8a7745: Adjust SMP routine size > > ARM: dts: r8a7790: Adjust SMP routine size > > ARM: dts: r8a7791: Adjust SMP routine size > > ARM: dts: r8a7792: Adjust SMP routine size > > ARM: dts: r8a7793: Adjust SMP routine size > > ARM: dts: r8a7794: Adjust SMP routine size > > soc: renesas: rcar-rst: Enable watchdog as reset trigger for Gen2 > > ARM: shmobile: rcar-gen2: Add watchdog support > > dt-bindings: watchdog: renesas-wdt: Add R-Car Gen2 support > > watchdog: renesas_wdt: Add R-Car Gen2 support > > watchdog: renesas_wdt: Add restart handler > > ARM: shmobile: defconfig: Enable RENESAS_WDT_GEN > > clk: renesas: r8a7743: Add rwdt clock > > clk: renesas: r8a7745: Add rwdt clock > > clk: renesas: r8a7790: Add rwdt clock > > clk: renesas: r8a7791/r8a7793: Add rwdt clock > > clk: renesas: r8a7794: Add rwdt clock > > ARM: dts: r8a7743: Add watchdog support to SoC dtsi > > ARM: dts: r8a7745: Add watchdog support to SoC dtsi > > ARM: dts: r8a7790: Add watchdog support to SoC dtsi > > ARM: dts: r8a7791: Add watchdog support to SoC dtsi > > ARM: dts: r8a7794: Add watchdog support to SoC dtsi > > ARM: dts: iwg20m: Add watchdog support to SoM dtsi > > ARM: dts: iwg22m: Add watchdog support to SoM dtsi > > > > .../devicetree/bindings/watchdog/renesas-wdt.txt | 19 ++++++-- > > arch/arm/boot/dts/r8a7743-iwg20m.dtsi | 5 ++ > > arch/arm/boot/dts/r8a7743.dtsi | 12 ++++- > > arch/arm/boot/dts/r8a7745-iwg22m.dtsi | 5 ++ > > arch/arm/boot/dts/r8a7745.dtsi | 12 ++++- > > arch/arm/boot/dts/r8a7790.dtsi | 12 ++++- > > arch/arm/boot/dts/r8a7791.dtsi | 12 ++++- > > arch/arm/boot/dts/r8a7792.dtsi | 2 +- > > arch/arm/boot/dts/r8a7793.dtsi | 2 +- > > arch/arm/boot/dts/r8a7794.dtsi | 12 ++++- > > arch/arm/configs/shmobile_defconfig | 1 + > > arch/arm/mach-shmobile/common.h | 6 +++ > > arch/arm/mach-shmobile/headsmp.S | 55 ++++++++++++++++++++++ > > arch/arm/mach-shmobile/platsmp-apmu.c | 1 + > > arch/arm/mach-shmobile/pm-rcar-gen2.c | 15 ++++-- > > drivers/clk/renesas/r8a7743-cpg-mssr.c | 2 + > > drivers/clk/renesas/r8a7745-cpg-mssr.c | 2 + > > drivers/clk/renesas/r8a7790-cpg-mssr.c | 2 + > > drivers/clk/renesas/r8a7791-cpg-mssr.c | 2 + > > drivers/clk/renesas/r8a7794-cpg-mssr.c | 2 + > > drivers/soc/renesas/rcar-rst.c | 35 +++++++++++--- > > drivers/watchdog/renesas_wdt.c | 39 +++++++++++++-- > > Thanks, I've queued the clock patches in clk-renesas-for-v4.17, as they are > a hard dependency for: > (1) The new reset vector in arch/arm/mach-shmobile/ > (2) The watchdog driver. > > Note that the watchdog driver itself (2) has a hard dependency on the > new reset vector (1). Thanks, I have marked the watchdog driver patch as Deferred. Please resubmit or otherwise ping me once they dependencies are in an rc release. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
