Added initial binding documentation for S2MPA01 MFD.
Signed-off-by: Sachin Kamat <sachin.kamat@xxxxxxxxxx>
---
Changes since v2:
* Re-worded as suggested by Mark Rutland
---
Documentation/devicetree/bindings/mfd/s2mpa01.txt | 90 +++++++++++++++++++++
1 file changed, 90 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/s2mpa01.txt
diff --git a/Documentation/devicetree/bindings/mfd/s2mpa01.txt b/Documentation/devicetree/bindings/mfd/s2mpa01.txt
new file mode 100644
index 000000000000..c13d3d8c3947
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/s2mpa01.txt
@@ -0,0 +1,90 @@
+
+* Samsung S2MPA01 Voltage and Current Regulator
+
+The Samsung S2MPA01 is a multi-function device which includes high
+efficiency buck converters including Dual-Phase buck converter, various LDOs,
+and an RTC. It is interfaced to the host controller using an I2C interface.
+Each sub-block is addressed by the host system using different I2C slave
+addresses.
+
+Required properties:
+- compatible: Should be "samsung,s2mpa01-pmic".
+- reg: Specifies the I2C slave address of the PMIC block. It should be 0x66.
+
+Optional properties:
+- interrupt-parent: Specifies the phandle of the interrupt controller to which
+ the interrupts from s2mpa01 are delivered to.
+- interrupts: An interrupt specifier for the sole interrupt generated by the
+ device.
+
+Optional nodes:
+- regulators: The regulators of s2mpa01 that have to be instantiated should be
+ included in a sub-node named 'regulators'. Regulator nodes and constraints
+ included in this sub-node use the standard regulator bindings which are
+ documented elsewhere.
+
+Properties for BUCK regulator nodes:
+- regulator-ramp-delay: ramp delay in uV/us. May be 6250, 12500
+ (default), 25000, or 50000. May be 0 for disabling the ramp delay on
+ BUCK{1,2,3,4}.
+
+ In the absence of the regulator-ramp-delay property, the default ramp
+ delay will be used.
+
+ NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set
+ for a particular group of BUCKs. So provide same regulator-ramp-delay=<value>.
+
+ The following BUCKs share ramp settings:
+ * 1 and 6
+ * 2 and 4
+ * 8, 9, and 10
+
+The following are the names of the regulators that the s2mpa01 PMIC block
+supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
+as per the datasheet of s2mpa01.
+
+ - LDOn
+ - valid values for n are 1 to 26
+ - Example: LDO1, LD02, LDO26
+ - BUCKn
+ - valid values for n are 1 to 10.
+ - Example: BUCK1, BUCK2, BUCK9
+
+Example:
+
+ s2mpa01_pmic@66 {
+ compatible = "samsung,s2mpa01-pmic";
+ reg = <0x66>;
+
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VDDQ_MMC2";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-ramp-delay = <50000>;
+ };
+ };
+ };
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
