On Thu, Feb 15, 2018 at 11:39:15AM +0100, Andrzej Hajda wrote:
> These bindings allow to describe most known standard USB connectors
> and it should be possible to extend it if necessary.
> USB connectors, beside USB can be used to route other protocols,
> for example UART, Audio, MHL. In such case every device passing data
> through the connector should have appropriate graph bindings.
>
> Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
> ---
> v3:
> - removed MHL port (samsung connector will have separate bindings),
> - added 2nd example for USB-C,
> - improved formatting
> v2:
> - moved connector type(A,B,C) to compatible string (Rob),
> - renamed size property to type (Rob),
> - changed type description to be less confusing (Laurent),
> - removed vendor specific compatibles (implied by graph port number),
> - added requirement of connector being a child of IC (Rob),
> - removed max-mode (subtly suggested by Rob, it should be detected anyway
> by USB Controller in runtime, downside is that device is not able to
> report its real capabilities, maybe better would be to make it optional(?)),
> - assigned port numbers to data buses (Rob).
>
> Regards
> Andrzej
>
> Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
>
> dt-bindings: add bindings for USB physical connector v3
> ---
> .../bindings/connector/usb-connector.txt | 74 ++++++++++++++++++++++
> 1 file changed, 74 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/connector/usb-connector.txt
>
> diff --git a/Documentation/devicetree/bindings/connector/usb-connector.txt b/Documentation/devicetree/bindings/connector/usb-connector.txt
> new file mode 100644
> index 000000000000..1efda92639da
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/connector/usb-connector.txt
> @@ -0,0 +1,74 @@
> +USB Connector
> +=============
> +
> +USB connector node represents physical USB connector. It should be
> +a child of USB interface controller.
> +
> +Required properties:
> +- compatible: describes type of the connector, must be one of:
> + "usb-a-connector",
> + "usb-b-connector",
> + "usb-c-connector".
> +
> +Optional properties:
> +- label: symbolic name for the connector,
> +- type: size of the connector, should be specified in case of USB-A, USB-B
> + non-standard (large) connector sizes: "mini", "micro".
The smaller connectors are standard too. Perhaps "non-fullsize connector
sizes".
We're missing a micro-AB connector, but I think those are actually
pretty rare. Most phones are micro-B connectors, but do both host and
device.
> +
> +Required nodes:
> +- any data bus to the connector should be modeled using the OF graph bindings
> + specified in bindings/graph.txt, unless the bus is between parent node and
> + the connector. Since single connector can have multpile data buses every bus
> + has assigned OF graph port number as follows:
> + 0: High Speed (HS), present in all connectors,
> + 1: Super Speed (SS), present in SS capable connectors,
This should also say endpoint 0 is USB-SS, endpoint 1 (and higher?) is
Alternate Mode. And show in the example.
> + 2: Sideband use (SBU), present in USB-C.
> +
> +Examples
> +--------
> +
> +1. Micro-USB connector with HS lines routed via controller (MUIC):
> +
> +muic-max77843@66 {
> + ...
> + usb_con: connector {
> + compatible = "usb-b-connector";
> + label = "micro-USB";
> + type = "micro";
> + };
> +};
> +
> +2. USB-C connector attached to CC controller (s2mm005), HS lines routed
> +to companion PMIC (max77865), SS lines to USB3 PHY and SBU to DisplayPort:
Having SBU to DP but no DP video path connection is wrong.
> +
> +ccic: s2mm005@33 {
> + ...
> + usb_con: connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + usb_con_hs: endpoint {
> + remote-endpoint = <&max77865_usbc_hs>;
> + };
> + };
> + port@1 {
> + reg = <1>;
> + usb_con_ss: endpoint {
> + remote-endpoint = <&usbdrd_phy_ss>;
> + };
> + };
> + port@2 {
> + reg = <2>;
> + usb_con_sbu: endpoint {
> + remote-endpoint = <&dp_aux>;
> + };
> + };
> + };
> + };
> +};
> --
> 2.16.1
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
