Add device binding documentation for Qualcomm Technology Inc's RPMH RSC
driver. The hardware block is used for communicating resource state
requests for shared resources.
Cc: devicetree@xxxxxxxxxxxxxxx
Signed-off-by: Lina Iyer <ilina@xxxxxxxxxxxxxx>
---
.../devicetree/bindings/arm/msm/rpmh-rsc.txt | 146 +++++++++++++++++++++
1 file changed, 146 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/msm/rpmh-rsc.txt
diff --git a/Documentation/devicetree/bindings/arm/msm/rpmh-rsc.txt b/Documentation/devicetree/bindings/arm/msm/rpmh-rsc.txt
new file mode 100644
index 000000000000..6cb36ae98bf9
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/msm/rpmh-rsc.txt
@@ -0,0 +1,146 @@
+RPMH RSC:
+------------
+
+RPMH is the mechanism for communicating with the hardened resource
+accelerators. Requests to the resources can be written to the TCS mailbox
+registers and using a (addr, val) pair and triggered. Messages in the TCS are
+then sent in sequence over an internal bus.
+
+The hardware block (Direct Resource Voter or DRV) is a part of the h/w entity
+(Resource State Coordinator a.k.a RSC) that can handle a multiple sleep and
+active/wake resource requests. Multiple such DRVs can exist in a SoC and can
+be written to from Linux. The structure of each DRV follows the same template
+with a few variations that are captured by the properties here.
+
+Each DRV could have 'm' TCS instances. Each TCS could have 'n' slots. Each
+slot has a header (u32), address (u32), data (u32), status (u32) and a
+read-response (u32). A TCS when triggered will send all the enabled commands
+of the 'n' commands in that slot in sequence.
+
+A TCS may be triggered from Linux or triggered by the F/W after all the CPUs
+have powered off to facilitate idle power saving. TCS could be classified as -
+
+ SLEEP, /* Triggered by F/W */
+ WAKE, /* Triggered by F/W */
+ ACTIVE, /* Triggered by Linux */
+ CONTROL /* Triggered by F/W */
+
+The order in which they are described in the DT, should match the hardware
+configuration.
+
+Requests can be made for the state of a resource, when the subsystem is active
+or idle. When all subsystems like Modem, GPU, CPU are idle, the resource state
+will be an aggregate of the sleep votes from each of those subsystem. Drivers
+may request a sleep value for their shared resources in addition to the active
+mode requests.
+
+Control requests are instance specific requests that may or may not reach an
+accelerator. Only one platform device in Linux can request a control channel
+on a DRV.
+
+CONTROLLER:
+----------
+
+PROPERTIES:
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: Should be "qcom,rpmh-rsc".
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: The first register specifies the base address of the DRV.
+ The second register specifies the start address of the
+ TCS.
+
+- reg-names:
+ Usage: required
+ Value type: <string>
+ Definition: Maps the register specified in the reg property. Must be
+ "drv" and "tcs".
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-interrupt>
+ Definition: The interrupt that trips when a message complete/response
+ is received for this DRV from the accelerators.
+
+- qcom,drv-id:
+ Usage: required
+ Value type: <u32>
+ Definition: the id of the DRV in the RSC block.
+
+- qcom,tcs-config:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: the tuple defining the configuration of TCS.
+ Must have 2 cells which describe each TCS type.
+ <type number_of_tcs>.
+ The order of the TCS must match the hardware
+ configuration.
+ - Cell #1 (TCS Type): TCS types to be specified -
+ SLEEP_TCS
+ WAKE_TCS
+ ACTIVE_TCS
+ CONTROL_TCS
+ - Cell #2 (Number of TCS): <u32>
+
+- label:
+ Usage: optional
+ Value type: <string>
+ Definition: Name for the RSC. The name would be used in trace logs.
+
+Platform drivers that want to use the RSC to communicate with RPMH must
+specify their bindings as child of the corresponding RSC controllers.
+
+EXAMPLE 1:
+
+For a TCS whose RSC base address is is 0x179C0000 and is at a DRV id of 2, the
+register offsets for DRV2 start at 0D00, the register calculations are like
+this -
+First tuple: 0x179C0000 + 0x10000 * 2 = 0x179E0000
+Second tuple: 0x179E0000 + 0xD00 = 0x179E0D00
+
+ apps_rsc: rsc@179e000 {
+ label = "apps_rsc";
+ compatible = "qcom,rpmh-rsc";
+ reg = <0x179e0000 0x10000>, <0x179e0d00 0x3000>;
+ reg-names = "drv", "tcs";
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>
+ qcom,drv-id = <2>;
+ qcom,tcs-config = <SLEEP_TCS 3>,
+ <WAKE_TCS 3>,
+ <ACTIVE_TCS 2>,
+ <CONTROL_TCS 1>;
+
+ foo-clk {
+ compatible = "foo-clk";
+ };
+ };
+
+EXAMPLE 2:
+
+For a TCS whose RSC base address is 0xAF20000 and is at DRV id of 0, the
+register offsets for DRV0 start at 01C00, the register calculations are like
+this -
+First tuple: 0xAF20000
+Second tuple: 0xAF20000 + 0x1C00 = 0xAF21C00
+
+ disp_rsc: rsc@af20000 {
+ label = "disp_rsc";
+ compatible = "qcom,rpmh-rsc";
+ reg = <0xaf20000 0x10000>, <0xaf21c00 0x3000>;
+ reg-names = "drv", "tcs";
+ interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,drv-id = <0>;
+ qcom,tcs-config = <SLEEP_TCS 1>,
+ <WAKE_TCS 1>,
+ <ACTIVE_TCS 0>,
+ <CONTROL_TCS 0>;
+
+ foo-clk {
+ compatible = "foo-clk";
+ };
+ };
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
