On Thu, Feb 08, 2018 at 04:01:42PM +0800, Baolin Wang wrote:
> This patch adds the device tree bindings for the Spreadtrum EIC
> controller. The EIC can be recognized as one special type of GPIO,
> which can only be used as input.
>
> Signed-off-by: Baolin Wang <baolin.wang@xxxxxxxxxx>
> ---
> .../devicetree/bindings/gpio/gpio-eic-sprd.txt | 51 ++++++++++++++++++++
> 1 file changed, 51 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt
>
> diff --git a/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt b/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt
> new file mode 100644
> index 0000000..34f194f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt
> @@ -0,0 +1,51 @@
> +Spreadtrum EIC controller bindings
> +
> +The EIC is the abbreviation of external interrupt controller, which
> +is only can be used as input mode. The EIC controller includes 4
> +sub-modules: EIC-Debounce, EIC-Latch, EIC-Async, EIC-Sync.
> +
> +The EIC-debounce sub-module provides up to 8 source input signal
> +connection. A debounce machanism is used to capture input signal's
> +stable status (ms grade) and a single-trigger mechanism is introduced
> +into this sub-module to enhance the input event detection reliability.
> +In addition, this sub-module's clock can be shut-off automatically to
> +reduce power dissipation. The debounce range is from 1ms to 4s with
> +the step of 1ms. If the input signal is shorter than 1ms, it will be
> +omitted as this sub-module.
> +
> +The EIC-latch sub-module is used to latch some special input signal
> +and send interrupts to MCU core, and it can provide up to 8 latch
> +source input signal connection.
> +
> +The EIC-async sub-module uses 32k clock to capture short signal (us
> +grade) to generate interrupt to MCU by level or edge trigger.
> +
> +The EIC-sync is similar with GPIO's input function.
> +
> +Required properties:
> +- compatible: Should be one of the following:
> + "sprd,sc9860-eic-debounce",
> + "sprd,sc9860-eic-latch",
> + "sprd,sc9860-eic-async",
> + "sprd,sc9860-eic-sync",
> + "sprd,sc27xx-eic-debounce".
> +- reg: Define the base and range of the I/O address space containing
> + the GPIO controller registers.
> +- gpio-controller: Marks the device node as a GPIO controller.
Why a gpio controller? Do you read the input pin state?
> +- #gpio-cells: Should be <2>. The first cell is the gpio number and
> + the second cell is used to specify optional parameters.
> +- interrupt-controller: Marks the device node as an interrupt controller.
> +- #interrupt-cells: Should be <2>. Specifies the number of cells needed
> + to encode interrupt source.
> +- interrupts: Should be the port interrupt shared by all the gpios.
> +
> +Example:
> + eic_debounce: eic@40210000 {
interrupt-controller@...
Or (if this remains a gpio controller)
gpio@...
> + compatible = "sprd,sc9860-eic-debounce";
> + reg = <0 0x40210000 0 0x80>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
The example doesn't seem to match your description of the block or
blocks. You talk about a bunch of sub modules and then there's just this
one node?
> + };
> --
> 1.7.9.5
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
