Hi Kieran, On Tuesday, 13 February 2018 15:14:43 EET Kieran Bingham wrote: > On 13/02/18 12:06, Laurent Pinchart wrote: > > On Tuesday, 13 February 2018 00:07:49 EET Kieran Bingham wrote: > >> From: Jean-Michel Hautbois <jean-michel.hautbois@xxxxxxxxxxx> > >> > >> The ADV7604 has thirteen 256-byte maps that can be accessed via the main > >> I²C ports. Each map has it own I²C address and acts as a standard slave > >> device on the I²C bus. > >> > >> Extend the device tree node bindings to be able to override the default > >> addresses so that address conflicts with other devices on the same bus > >> may be resolved at the board description level. > >> > >> Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@xxxxxxxxxxx> > >> [Kieran: Re-adapted for mainline] > >> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@xxxxxxxxxxxxxxxx> > >> Reviewed-by: Rob Herring <robh@xxxxxxxxxx> > > > > Nitpicking, I might not mention i2c_new_secondary_device in the subject, > > as this is a DT bindings change. I don't mind too much though, as long as > > the bindings themselves don't contain Linux-specific information, and they > > don't, so > > How about: ... adv7604: Extend bindings to allow specifying slave map > addresses Sounds good to me. > > Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> > > Collected, thanks. > > -- > Kieran > > >> --- > >> > >> Based upon the original posting : > >> https://lkml.org/lkml/2014/10/22/469 > >> > >> v2: > >> - DT Binding update separated from code change > >> - Minor reword to commit message to account for DT only change. > >> - Collected Rob's RB tag. > >> > >> v3: > >> - Split map register addresses into individual declarations. > >> > >> .../devicetree/bindings/media/i2c/adv7604.txt | 18 > >> > >> ++++++++++++++++-- 1 file changed, 16 insertions(+), 2 deletions(-) > >> > >> diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt > >> b/Documentation/devicetree/bindings/media/i2c/adv7604.txt index > >> 9cbd92eb5d05..ebb5f070c05b 100644 > >> --- a/Documentation/devicetree/bindings/media/i2c/adv7604.txt > >> +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt > >> > >> @@ -13,7 +13,11 @@ Required Properties: > >> - "adi,adv7611" for the ADV7611 > >> - "adi,adv7612" for the ADV7612 > >> > >> - - reg: I2C slave address > >> + - reg: I2C slave addresses > >> + The ADV76xx has up to thirteen 256-byte maps that can be accessed > >> via > >> the + main I²C ports. Each map has it own I²C address and acts as a > >> standard + slave device on the I²C bus. The main address is mandatory, > >> others are + optional and revert to defaults if not specified. > >> > >> - hpd-gpios: References to the GPIOs that control the HDMI hot-plug > >> > >> detection pins, one per HDMI input. The active flag indicates the > >> GPIO > >> > >> @@ -35,6 +39,11 @@ Optional Properties: > >> - reset-gpios: Reference to the GPIO connected to the device's reset > >> pin. > >> > >> - default-input: Select which input is selected after reset. > >> + - reg-names : Names of maps with programmable addresses. > >> + It can contain any map needing a non-default address. > >> + Possible maps names are : > >> + "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe", > >> + "rep", "edid", "hdmi", "test", "cp", "vdp" > >> > >> Optional Endpoint Properties: > >> @@ -52,7 +61,12 @@ Example: > >> hdmi_receiver@4c { > >> > >> compatible = "adi,adv7611"; > >> > >> - reg = <0x4c>; > >> + /* > >> + * The edid page will be accessible @ 0x66 on the i2c bus. All > >> + * other maps will retain their default addresses. > >> + */ > >> + reg = <0x4c>, <0x66>; > >> + reg-names "main", "edid"; > >> > >> reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; > >> hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; -- Regards, Laurent Pinchart -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
