Add support for Advantech DMS-BA16 board, which uses
the Advantech BA-16 module.
Signed-off-by: Ken Lin <yungching0725@xxxxxxxxx>
---
Changes in v4:
- Fix the pinctrl entries order issue
- Correct the USB_OTG_ID pinmux
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-dms-ba16.dts | 139 +++++++++++++++++++++++++++++++++++
2 files changed, 140 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-dms-ba16.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ade7a38543dc..585c3da4a47a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -435,6 +435,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-dfi-fs700-m60.dtb \
imx6q-display5-tianma-tm070-1280x768.dtb \
imx6q-dmo-edmqmx6.dtb \
+ imx6q-dms-ba16.dtb \
imx6q-evi.dtb \
imx6q-gk802.dtb \
imx6q-gw51xx.dtb \
diff --git a/arch/arm/boot/dts/imx6q-dms-ba16.dts b/arch/arm/boot/dts/imx6q-dms-ba16.dts
new file mode 100644
index 000000000000..57761f3172fa
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-dms-ba16.dts
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6q-ba16.dtsi"
+
+/ {
+ model = "Advantech DMS-BA16";
+ compatible = "advantech,imx6q-dms-ba16", "advantech,imx6q-ba16", "fsl,imx6q";
+
+ reg_usb_otg_vbus: regulator-usbotgvbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotgvbus>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ sys_mclk: clock-sys-mclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <22000000>;
+ };
+
+ sound {
+ compatible = "fsl,imx6q-ba16-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx6q-ba16-sgtl5000";
+ ssi-controller = <&ssi1>;
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <1>;
+ mux-ext-port = <4>;
+ };
+};
+
+&ecspi5 {
+ cs-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi5>;
+ status = "okay";
+
+ m25_eeprom: m25p80@0 {
+ compatible = "atmel,at25256B", "atmel,at25";
+ spi-max-frequency = <20000000>;
+ size = <0x8000>;
+ pagesize = <64>;
+ reg = <0>;
+ address-width = <16>;
+ };
+};
+
+&iomuxc {
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0
+ MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x1b0b0
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x1b0b0
+ MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotgvbus: usbotgvbusgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
+ >;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ sgtl5000: codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&sys_mclk>;
+ lrclk-strength = <0x3>;
+ VDDA-supply = <®_1p8v>;
+ VDDIO-supply = <®_3p3v>;
+ };
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&sata {
+ fsl,no-spread-spectrum;
+ fsl,transmit-atten-16ths = <12>;
+ fsl,transmit-boost-mdB = <3330>;
+ fsl,transmit-level-mV = <1133>;
+ fsl,receive-dpll-mode = <1>;
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ dr_mode = "otg";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc4>;
+ bus-width = <8>;
+ cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
--
2.11.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
