On Wed, Feb 07, 2018 at 03:17:04AM +0800, Ken Lin wrote:
> Add support for Advantech DMS-BA16 board, which uses
> the Advantech BA-16 module.
>
> Signed-off-by: Ken Lin <yungching0725@xxxxxxxxx>
> ---
> Changes in v3:
> - Fix the SPDX lines issue
> - Fix the eeprom setting issue
>
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/imx6q-dms-ba16.dts | 140 +++++++++++++++++++++++++++++++++++
> 2 files changed, 141 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6q-dms-ba16.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index ade7a38543dc..585c3da4a47a 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -435,6 +435,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
> imx6q-dfi-fs700-m60.dtb \
> imx6q-display5-tianma-tm070-1280x768.dtb \
> imx6q-dmo-edmqmx6.dtb \
> + imx6q-dms-ba16.dtb \
> imx6q-evi.dtb \
> imx6q-gk802.dtb \
> imx6q-gw51xx.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-dms-ba16.dts b/arch/arm/boot/dts/imx6q-dms-ba16.dts
> new file mode 100644
> index 000000000000..b5047fd88290
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-dms-ba16.dts
> @@ -0,0 +1,140 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include "imx6q-ba16.dtsi"
> +
> +/ {
> + model = "Advantech DMS-BA16";
> + compatible = "advantech,imx6q-dms-ba16", "advantech,imx6q-ba16", "fsl,imx6q";
> +
> + reg_usb_otg_vbus: regulator-usbotgvbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotgvbus>;
> + gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + sys_mclk: clock-sys-mclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <22000000>;
> + };
> +
> + sound {
> + compatible = "fsl,imx6q-ba16-sgtl5000",
> + "fsl,imx-audio-sgtl5000";
> + model = "imx6q-ba16-sgtl5000";
> + ssi-controller = <&ssi1>;
> + audio-codec = <&sgtl5000>;
> + audio-routing =
> + "MIC_IN", "Mic Jack",
> + "Mic Jack", "Mic Bias",
> + "Headphone Jack", "HP_OUT";
> + mux-int-port = <1>;
> + mux-ext-port = <4>;
> + };
> +};
> +
> +&ecspi5 {
> + cs-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi5>;
> + status = "okay";
> +
> + m25_eeprom: m25p80@0 {
> + compatible = "atmel,at25256B", "atmel,at25";
> + spi-max-frequency = <20000000>;
> + size = <0x8000>;
> + pagesize = <64>;
> + reg = <0>;
> + address-width = <16>;
> + };
> +};
> +
> +&iomuxc {
> +
Unnecessary newline.
> + pinctrl_usbotgvbus: usbotgvbusgrp {
Please keep the pinctrl entries under iomuxc node alphabetically sorted.
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0
> + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
MX6QDL_PAD_GPIO_1__USB_OTG_ID shouldn't belong to this group but
pinctrl_usbotg. However that has been defined in imx6q-ba16.dtsi using
another USB_OTG_ID pinmux. Confusing.
Shawn
> + >;
> + };
> +
> + pinctrl_i2c1_gpio: i2c1gpiogrp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x1b0b0
> + MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x1b0b0
> + >;
> + };
> +
> + pinctrl_i2c2_gpio: i2c2gpiogrp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0
> + MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x1b0b0
> + >;
> + };
> +
> + pinctrl_i2c3_gpio: i2c3gpiogrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x1b0b0
> + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0
> + >;
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + sgtl5000: codec@a {
> + compatible = "fsl,sgtl5000";
> + reg = <0x0a>;
> + clocks = <&sys_mclk>;
> + lrclk-strength = <0x3>;
> + VDDA-supply = <®_1p8v>;
> + VDDIO-supply = <®_3p3v>;
> + };
> +};
> +
> +&pwm2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm2>;
> + status = "okay";
> +};
> +
> +&sata {
> + fsl,no-spread-spectrum;
> + fsl,transmit-atten-16ths = <12>;
> + fsl,transmit-boost-mdB = <3330>;
> + fsl,transmit-level-mV = <1133>;
> + fsl,receive-dpll-mode = <1>;
> + status = "okay";
> +};
> +
> +&usbotg {
> + vbus-supply = <®_usb_otg_vbus>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg>;
> + dr_mode = "otg";
> + disable-over-current;
> + status = "okay";
> +};
> +
> +&usdhc4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc4>;
> + bus-width = <8>;
> + cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
> + no-1-8-v;
> + keep-power-in-suspend;
> + wakeup-source;
> + status = "okay";
> +};
> --
> 2.11.0
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
