Hi,
Dne ponedeljek, 29. januar 2018 ob 19:05:26 CET je Rob Herring napisal(a):
> On Wed, Jan 17, 2018 at 09:14:15PM +0100, Jernej Skrabec wrote:
> > This commit adds all necessary compatibles and descriptions needed to
> > implement A83T HDMI pipeline.
> >
> > Mixer is already properly described, so only compatible is added.
> >
> > However, A83T TV TCON, which is connected to HDMI, doesn't have channel 0,
> > contrary to all TCONs currently described. Because of that, TCON
> > documentation is extended.
> >
> > A83T features Synopsys DW HDMI controller with a custom PHY which looks
> > like Synopsys Gen2 PHY with few additions. Since there is no
> > documentation, needed properties were found out through experimentation
> > and reading BSP code.
> >
> > At the end, example is added for newer SoCs, which feature DE2 and DW
> > HDMI.
> >
> > Signed-off-by: Jernej Skrabec <jernej.skrabec@xxxxxxxx>
> > ---
> >
> > .../bindings/display/sunxi/sun4i-drm.txt | 197
> > ++++++++++++++++++++- 1 file changed, 190 insertions(+), 7 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> > b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt index
> > cd626ee1147a..4fb380f3e53d 100644
> > --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> > +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> >
> > @@ -64,6 +64,52 @@ Required properties:
> > first port should be the input endpoint. The second should be the
> > output, usually to an HDMI connector.
> >
> > +DWC HDMI TX Encoder
> > +-------------------
> > +
> > +The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
> > +with Allwinner's own PHY IP. It supports audio and video outputs and CEC.
> > +
> > +These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
> > +Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
> > +following device-specific properties.
> > +
> > +Required properties:
> > +
> > + - compatible: value must be one of:
> > + * "allwinner,sun8i-a83t-dw-hdmi"
> > + - reg: base address and size of memory-mapped region
> > + - reg-io-width: See dw_hdmi.txt. Shall be 1.
> > + - interrupts: HDMI interrupt number
> > + - clocks: phandles to the clocks feeding the HDMI encoder
> > + * iahb: the HDMI bus clock
> > + * isfr: the HDMI register clock
> > + - clock-names: the clock names mentioned above
> > + - resets: phandle to the reset controller
> > + - reset-names: must be "ctrl"
> > + - phys: phandle to the DWC HDMI PHY
> > + - phy-names: must be "phy"
> > +
> > + - ports: A ports node with endpoint definitions as defined in
> > + Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > + first port should be the input endpoint. The second should be the
> > + output, usually to an HDMI connector.
> > +
> > +DWC HDMI PHY
> > +------------
> > +
> > +Required properties:
> > + - compatible: value must be one of:
> > + * allwinner,sun8i-a83t-hdmi-phy
> > + - reg: base address and size of memory-mapped region
> > + - clocks: phandles to the clocks feeding the HDMI PHY
> > + * bus: the HDMI PHY interface clock
> > + * mod: the HDMI PHY module clock
> > + * tmds: TMDS clock
> > + - clock-names: the clock names mentioned above
> > + - resets: phandle to the reset controller driving the PHY
> > + - reset-names: must be "phy"
> > +
> >
> > TV Encoder
> > ----------
> >
> > @@ -94,24 +140,23 @@ Required properties:
> > * allwinner,sun7i-a20-tcon
> > * allwinner,sun8i-a33-tcon
> > * allwinner,sun8i-a83t-tcon-lcd
> >
> > + * allwinner,sun8i-a83t-tcon-tv
> >
> > * allwinner,sun8i-v3s-tcon
> >
> > - reg: base address and size of memory-mapped region
> > - interrupts: interrupt associated to this IP
> >
> > - - clocks: phandles to the clocks feeding the TCON. Three are needed:
> >
> > + - clocks: phandles to the clocks feeding the TCON. One is needed:
> > - 'ahb': the interface clocks
> >
> > - - 'tcon-ch0': The clock driving the TCON channel 0
>
> Well, it didn't look right before saying 3 are needed, but listing 2.
> However, you can't just change this as it affects all the other SoCs.
> This should probably be a separate patch.
I had a feeling that all items which are not common to all compatibles should
be listed below and explained when they are needed. At least currently it's
done this way.
>
> > - resets: phandles to the reset controllers driving the encoder
> >
> > - "lcd": the reset line for the TCON channel 0
> >
> > - clock-names: the clock names mentioned above
> > - reset-names: the reset names mentioned above
> >
> > - - clock-output-names: Name of the pixel clock created
>
> Why is this removed?
>
> > - ports: A ports node with endpoint definitions as defined in
> >
> > Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > first port should be the input endpoint, the second one the output
> >
> > - The output may have multiple endpoints. The TCON has two channels,
> > + The output may have multiple endpoints. TCON can have two channels,
>
> Perhaps you should say "can have 1 or 2 channels".
Ok.
>
> > usually with the first channel being used for the panels interfaces
> > (RGB, LVDS, etc.), and the second being used for the outputs that
> > require another controller (TV Encoder, HDMI, etc.). The endpoints
> >
> > @@ -119,11 +164,16 @@ Required properties:
> > channel the endpoint is associated to. If that property is not
> > present, the endpoint number will be used as the channel number.
> >
> > +When TCON supports channel 0 (all TCONs except TV TCON on A83T), two
> > +more clocks are needed:
> > + - 'tcon-ch0': The clock driving the TCON channel 0
>
> Looks like one clock to me.
>
> > + - clock-output-names: Name of the pixel clock created
>
> It's better to not move this, but just add what compatibles it does or
> doesn't apply to.
>
> > +
> >
> > On SoCs other than the A33 and V3s, there is one more clock required:
> > - 'tcon-ch1': The clock driving the TCON channel 1
> >
> > -On SoCs that support LVDS (all SoCs but the A13, H3, H5 and V3s), you
> > -need one more reset line:
> > +When TCON support LVDS (all TCONs except TV TCON on A83T and those found
> >
> > +in A13, H3, H5 and V3s SoCs), you need one more reset line:
> > - 'lvds': The reset line driving the LVDS logic
> >
> > And on the A23, A31, A31s and A33, you need one more clock line:
> > @@ -226,6 +276,7 @@ supported.
> >
> > Required properties:
> > - compatible: value must be one of:
> > * allwinner,sun8i-a83t-de2-mixer-0
> >
> > + * allwinner,sun8i-a83t-de2-mixer-1
> >
> > * allwinner,sun8i-v3s-de2-mixer
> >
> > - reg: base address and size of the memory-mapped region.
> > - clocks: phandles to the clocks feeding the mixer
> >
> > @@ -261,7 +312,7 @@ Required properties:
> > - allwinner,pipelines: list of phandle to the display engine
> >
> > frontends (DE 1.0) or mixers (DE 2.0) available.
> >
> > -Example:
> >
> > +Example 1:
> > panel: panel {
> >
> > compatible = "olimex,lcd-olinuxino-43-ts";
> >
> > @@ -460,3 +511,135 @@ display-engine {
> >
> > compatible = "allwinner,sun5i-a13-display-engine";
> > allwinner,pipelines = <&fe0>;
> >
> > };
> >
> > +
>
> > +Example 2:
> Is this really different enough to need an example? Examples don't
> need to enumerate all possible options. They are often wrong because
> they don't compile on their own and that creates a maintenance burden.
This example is for second generation of display engine so pipeline is
different. Only TCON and connector examples are same, but 4 others are new, so
I thought it would be nice to show an example for it. But I can remove it in
next version if it is not needed.
Best regards,
Jernej
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
