On 02/11/14 13:08, Laurent Pinchart wrote:
> Hi Hans,
>
> On Tuesday 11 February 2014 10:23:03 Hans Verkuil wrote:
>> On 02/05/14 17:42, Laurent Pinchart wrote:
>>> Parse the device tree node to populate platform data.
>>>
>>> Cc: devicetree@xxxxxxxxxxxxxxx
>>> Signed-off-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
>>> ---
>>>
>>> .../devicetree/bindings/media/i2c/adv7604.txt | 56 ++++++++++++
>>> drivers/media/i2c/adv7604.c | 101 ++++++++++++++--
>>> 2 files changed, 143 insertions(+), 14 deletions(-)
>>> create mode 100644
>>> Documentation/devicetree/bindings/media/i2c/adv7604.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt
>>> b/Documentation/devicetree/bindings/media/i2c/adv7604.txt new file mode
>>> 100644
>>> index 0000000..0845c50
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
>>> @@ -0,0 +1,56 @@
>>> +* Analog Devices ADV7604/11 video decoder with HDMI receiver
>>> +
>>> +The ADV7604 and ADV7611 are multiformat video decoders with an integrated
>>> HDMI +receiver. The ADV7604 has four multiplexed HDMI inputs and one
>>> analog input, +and the ADV7611 has one HDMI input and no analog input.
>>> +
>>> +Required Properties:
>>> +
>>> + - compatible: Must contain one of the following
>>> + - "adi,adv7604" for the ADV7604
>>> + - "adi,adv7611" for the ADV7611
>>> +
>>> + - reg: I2C slave address
>>> +
>>> + - hpd-gpios: References to the GPIOs that control the HDMI hot-plug
>>> + detection pins, one per HDMI input. The active flag indicates the
>>> GPIO
>>> + level that enables hot-plug detection.
>>> +
>>> +Optional Properties:
>>> +
>>> + - reset-gpios: Reference to the GPIO connected to the device's reset
>>> pin. +
>>> + - adi,default-input: Index of the input to be configured as default.
>>> Valid + values are 0..5 for the ADV7604 and 0 for the ADV7611.
>>> +
>>> + - adi,disable-power-down: Boolean property. When set forces the device
>>> to + ignore the power-down pin. The property is valid for the ADV7604
>>> only as + the ADV7611 has no power-down pin.
>>> +
>>> + - adi,disable-cable-reset: Boolean property. When set disables the HDMI
>>> + receiver automatic reset when the HDMI cable is unplugged.
>>> +
>>> +Example:
>>> +
>>> + hdmi_receiver@4c {
>>> + compatible = "adi,adv7611";
>>> + reg = <0x4c>;
>>> +
>>> + reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
>>> + hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
>>> +
>>> + adi,default-input = <0>;
>>> +
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + port@0 {
>>> + reg = <0>;
>>> + };
>>> + port@1 {
>>> + reg = <1>;
>>> + hdmi_in: endpoint {
>>> + remote-endpoint = <&ccdc_in>;
>>> + };
>>> + };
>>> + };
>>> diff --git a/drivers/media/i2c/adv7604.c b/drivers/media/i2c/adv7604.c
>>> index e586c1c..cd8a2dc 100644
>>> --- a/drivers/media/i2c/adv7604.c
>>> +++ b/drivers/media/i2c/adv7604.c
>>> @@ -32,6 +32,7 @@
>>>
>>> #include <linux/i2c.h>
>>> #include <linux/kernel.h>
>>> #include <linux/module.h>
>>>
>>> +#include <linux/of_gpio.h>
>>>
>>> #include <linux/slab.h>
>>> #include <linux/v4l2-dv-timings.h>
>>> #include <linux/videodev2.h>
>>>
>>> @@ -2641,13 +2642,83 @@ static const struct adv7604_chip_info
>>> adv7604_chip_info[] = {>
>>> },
>>>
>>> };
>>>
>>> +static struct i2c_device_id adv7604_i2c_id[] = {
>>> + { "adv7604", (kernel_ulong_t)&adv7604_chip_info[ADV7604] },
>>> + { "adv7611", (kernel_ulong_t)&adv7604_chip_info[ADV7611] },
>>> + { }
>>> +};
>>> +MODULE_DEVICE_TABLE(i2c, adv7604_i2c_id);
>>> +
>>> +static struct of_device_id adv7604_of_id[] = {
>>> + { .compatible = "adi,adv7604", .data = &adv7604_chip_info[ADV7604] },
>>> + { .compatible = "adi,adv7611", .data = &adv7604_chip_info[ADV7611] },
>>> + { }
>>> +};
>>> +MODULE_DEVICE_TABLE(of, adv7604_of_id);
>>> +
>>> +static int adv7604_parse_dt(struct adv7604_state *state)
>>
>> Put this under #ifdef CONFIG_OF.
>
> #ifdef CONFIG_OF has been discouraged. I'll add an IS_ENABLED(CONFIG_OF) to
> condition the call of adv7604_parse_dt() and let the compiler optimize the
> function out, but I've been recommended to fix compilation errors instead of
> using conditional compilation.
>
>> It fails to compile if CONFIG_OF is not set (as it is in my case since this
>> driver is used with a PCIe card).
>
> What's the compilation failure ?
drivers/media/i2c/adv7604.c: In function ‘adv7604_parse_dt’:
drivers/media/i2c/adv7604.c:2671:48: warning: dereferencing ‘void *’ pointer [enabled by default]
state->info = of_match_node(adv7604_of_id, np)->data;
^
drivers/media/i2c/adv7604.c:2671:48: error: request for member ‘data’ in something not a structure or union
make[3]: *** [drivers/media/i2c/adv7604.o] Error 1
>
>>> +{
>>> + struct device_node *np;
>>> + unsigned int i;
>>> + int ret;
>>> +
>>> + np = state->i2c_clients[ADV7604_PAGE_IO]->dev.of_node;
>>> + state->info = of_match_node(adv7604_of_id, np)->data;
>>> +
>>> + state->pdata.disable_pwrdnb =
>>> + of_property_read_bool(np, "adi,disable-power-down");
>>> + state->pdata.disable_cable_det_rst =
>>> + of_property_read_bool(np, "adi,disable-cable-reset");
>>> +
>>> + ret = of_property_read_u32(np, "adi,default-input",
>>> + &state->pdata.default_input);
>>> + if (ret < 0)
>>> + state->pdata.default_input = -1;
>>> +
>>> + for (i = 0; i < state->info->num_dv_ports; ++i) {
>>> + enum of_gpio_flags flags;
>>> +
>>> + state->pdata.hpd_gpio[i] =
>>> + of_get_named_gpio_flags(np, "hpd-gpios", i, &flags);
>>> + if (IS_ERR_VALUE(state->pdata.hpd_gpio[i]))
>>> + continue;
>>> +
>>> + state->pdata.hpd_gpio_low[i] = flags == OF_GPIO_ACTIVE_LOW;
>>> + }
>>> +
>>> + /* Disable the interrupt for now as no DT-based board uses it. */
>>> + state->pdata.int1_config = ADV7604_INT1_CONFIG_DISABLED;
>>> +
>>> + /* Use the default I2C addresses. */
>>> + state->pdata.i2c_addresses[ADV7604_PAGE_AVLINK] = 0x42;
>>> + state->pdata.i2c_addresses[ADV7604_PAGE_CEC] = 0x40;
>>> + state->pdata.i2c_addresses[ADV7604_PAGE_INFOFRAME] = 0x3e;
>>> + state->pdata.i2c_addresses[ADV7604_PAGE_ESDP] = 0x38;
>>> + state->pdata.i2c_addresses[ADV7604_PAGE_DPP] = 0x3c;
>>> + state->pdata.i2c_addresses[ADV7604_PAGE_AFE] = 0x26;
>>> + state->pdata.i2c_addresses[ADV7604_PAGE_REP] = 0x32;
>>> + state->pdata.i2c_addresses[ADV7604_PAGE_EDID] = 0x36;
>>> + state->pdata.i2c_addresses[ADV7604_PAGE_HDMI] = 0x34;
>>> + state->pdata.i2c_addresses[ADV7604_PAGE_TEST] = 0x30;
>>> + state->pdata.i2c_addresses[ADV7604_PAGE_CP] = 0x22;
>>> + state->pdata.i2c_addresses[ADV7604_PAGE_VDP] = 0x24;
>>> +
>>> + /* HACK: Hardcode the remaining platform data fields. */
>>> + state->pdata.blank_data = 1;
>>> + state->pdata.op_656_range = 1;
>>> + state->pdata.alt_data_sat = 1;
>>> + state->pdata.insert_av_codes = 1;
>>> + state->pdata.op_format_mode_sel = ADV7604_OP_FORMAT_MODE0;
>>> +
>>> + return 0;
>>> +}
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
