This patchset adds support for the PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira.
Following boards are included:
phyBOARD-Mira with phyCORE-i.MX 6 Quad/Dual with:
- i.MX 6Quad/Dual SOC
- NAND or eMMC
- HDMI interface
- LVDS display interface
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
This board also contains an LVDS camera interface and parallel display
interface which are not yet supported.
phyBAORD-Mira with phyCORE-i.MX 6 DualLight/Solo with:
- i.MX 6DualLight/Solo
- NAND
- HDMI interface
- 100 MBit/s Ethernet
- USB Host
- RS232
phyBOARD-Mira with phyCORE-i.MX 6 QuadPlus with:
- i.MX 6QuadPlus SOC
- NAND
- HDMI interface
- LVDS display interface
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
This board also contains an LVDS camera interface and parallel display
interface which are not yet supported.
The entire series is based on v4.15-rc4.
Changes since v1:
- Removed unnecessary ipu aliases
- Added unit-address to memory node name
- Fixed eeprom compatible to correct vendor name (atmel instead of cat)
- Fixed rtc compatible to correct vendor name (microcrystal instead of mc)
- Changed pcie regulator to be used with vpcie-supply in &pcie node and
removed regulator-always-on
- Changed pcie reset-gpio polarity to GPIO_ACTIVE_LOW
- Replaced fsl,uart-has-rtscts by uart-has-rtscts
- Fixed typos in defconfig patch
Changes since v2:
- Fixed typo in patch subject PATCH 4/6
- Added reviewed by tags on PATCH 4/6 and PATCH 6/6
Changes since v3:
- Removed model and compatible from phycore dtsi
- Changed flash compatible to jedec,spi-nor
- Renamed some_green node to som-led-green
- Dropped labels for eeprom, pmic, da9062_wdt and da9062_reg
- Renamed flash label to m25p80
- Put compatible at beginning of property lists
- Changed copyright year to 2018
- Added reviewed by tags on PATCH 1/6, 2/6, 3/6 and 5/6
Changes since v4:
- Rearranged &m25p80 node in dts files to fit alphabetical order
- Fixed a parenthesis for uniformity in mira dtsi
Christian Hemp (2):
ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK
ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6 DualLight/Solo
RDK
Enrico Scholz (1):
ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus
Stefan Riedmueller (3):
ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM
ARM: dts: imx6: Add initial support for phyBOARD-Mira
ARM: imx_v6_v7_defconfig: Enable Dialog Semiconductor DA9062 driver
arch/arm/boot/dts/Makefile | 4 +
arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts | 64 ++++
arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts | 72 ++++
arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts | 72 ++++
arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi | 390 ++++++++++++++++++++++
arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 279 ++++++++++++++++
arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts | 72 ++++
arch/arm/configs/imx_v6_v7_defconfig | 4 +
8 files changed, 957 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
create mode 100644 arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
