Hi Fabrizio, Happy to see that this patch series is of interest ;) As you can see in mail thread, Maxime Ripard is also testing it: https://www.mail-archive.com/linux-media@xxxxxxxxxxxxxxx/msg124322.html For BT656 support, it was not initially planned but it seems straightforward to code it, and anyway I have to add JPEG support, so I could add BT656 support in next patch series. For your symptom, I would say same as I said to Maxime, check first the polarity of sync signals (hysnc/vysnc/pclk) between ISP and OV5640. Note also that several frames are needed to get a non-black picture. You can also use the colorbar test to validate bus connection between ISP and sensor. Here are the yavta commands that I'm commonly using: * grab QVGA RGB565 raw frame (note the skip=10 to get a correct image) yavta -s 320x240 -n 3 --capture=13 --skip=10 --format=RGB565 /dev/video0 --file=grab-320x240-rgb565-#.raw * grab QVGA YUV frame yavta -s 320x240 -n 3 --capture=13 --skip=10 --format=YUYV /dev/video0 --file=grab-320x240-yuyv-#.raw * grab QVGA colorbar RGB565 raw frame yavta -s 320x240 -n 3 -w '0x009f0903 1' --capture=1 --format=RGB565 /dev/video0 --file=grab-colorbar-320x240-rgb565-#.raw * disable colorbars yavta -s 320x240 -n 3 -w '0x009f0903 0' /dev/video0 Hope this will help ! Best regards, Hugues. On 01/08/2018 09:54 PM, Fabrizio Castro wrote: > Hello Hugues, > > thank you for the patch series. > I am having a go with your patches, and although they seem alright, I don't seem to be able to grab a non-black picture on the iWave iwg20d in plain DVP mode, but if I switch to BT656 just by setting register 0x4730 to 0x01 (I know, it's a nasty hack...) I can get something sensible out. > > At the moment there is no proper BT656 support in the driver, I was wondering if you have any plans to enhance the ov5640 driver a little bit further to add proper BT656 support as it may be convenient. > > Do you know if someone else was able to get DVP to work by means of this patch series on a non-STM32 platform? > > Thanks, > Fabrizio > > >> Subject: [PATCH v5 0/5] Add OV5640 parallel interface and RGB565/YUYV support >> >> Enhance OV5640 CSI driver to support also DVP parallel interface. >> Add RGB565 (LE & BE) and YUV422 YUYV format in addition to existing >> YUV422 UYVY format. >> Some other improvements on chip identifier check and removal >> of warnings in powering phase around gpio handling. >> >> =========== >> = history = >> =========== >> version 5: >> - Refine bindings as per Sakari suggestion: >> https://www.mail-archive.com/linux-media@xxxxxxxxxxxxxxx/msg124048.html >> >> version 4: >> - Refine bindings as per Sakari suggestion: >> https://www.mail-archive.com/linux-media@xxxxxxxxxxxxxxx/msg123609.html >> - Parallel port control lines polarity can now be configured through >> devicetree >> >> version 3: >> - Move chip identifier check at probe according to Fabio Estevam comment: >> https://www.mail-archive.com/linux-media@xxxxxxxxxxxxxxx/msg122575.html >> - Use 16 bits register read for this check as per Steve Longerbeam comment: >> https://www.mail-archive.com/linux-media@xxxxxxxxxxxxxxx/msg122692.html >> - Update bindings to document parallel mode support as per Fabio Estevam comment: >> https://www.mail-archive.com/linux-media@xxxxxxxxxxxxxxx/msg122576.html >> - Enable the whole 10 bits parallel output and document 8/10 bits support >> in ov5640_set_stream_dvp() to answer to Steve Longerbeam comment: >> https://www.mail-archive.com/linux-media@xxxxxxxxxxxxxxx/msg122693.html >> >> version 2: >> - Fix comments from Sakari Ailus: >> https://www.mail-archive.com/linux-media@xxxxxxxxxxxxxxx/msg122259.html >> - Revisit ov5640_set_stream_dvp() to only configure DVP at streamon >> - Revisit ov5640_set_stream_dvp() implementation with fewer register settings >> >> version 1: >> - Initial submission >> >> Hugues Fruchet (5): >> media: ov5640: switch to gpiod_set_value_cansleep() >> media: ov5640: check chip id >> media: dt-bindings: ov5640: refine CSI-2 and add parallel interface >> media: ov5640: add support of DVP parallel interface >> media: ov5640: add support of RGB565 and YUYV formats >> >> .../devicetree/bindings/media/i2c/ov5640.txt | 46 ++- >> drivers/media/i2c/ov5640.c | 325 ++++++++++++++++++--- >> 2 files changed, 324 insertions(+), 47 deletions(-) >> >> -- >> 1.9.1 >> >> -- >> To unsubscribe from this list: send the line "unsubscribe devicetree" in >> the body of a message to majordomo@xxxxxxxxxxxxxxx >> More majordomo info at http://vger.kernel.org/majordomo-info.html > > > > Renesas Electronics Europe Ltd, Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, UK. Registered in England & Wales under Registered No. 04586709. > ��.n��������+%������w��{.n����z�{��ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f
