Re: [PATCH v5 1/2] PCI: mediatek: Clear IRQ status after IRQ dispatched to avoid reentry

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 05/01/18 11:51, Honghui Zhang wrote:
> On Thu, 2018-01-04 at 19:04 +0000, Marc Zyngier wrote:
>> On 04/01/18 18:40, Lorenzo Pieralisi wrote:
>>> [+Marc]
>>>
>>> On Wed, Dec 27, 2017 at 08:59:53AM +0800, honghui.zhang@xxxxxxxxxxxx wrote:
>>>> From: Honghui Zhang <honghui.zhang@xxxxxxxxxxxx>
>>>>
>>>> There maybe a same IRQ reentry scenario after IRQ received in current
>>>> IRQ handle flow:
>>>> 	EP device		PCIe host driver	EP driver
>>>> 1. issue an IRQ
>>>> 			2. received IRQ
>>>> 			3. clear IRQ status
>>>> 			4. dispatch IRQ
>>>> 						5. clear IRQ source
>>>> The IRQ status was not successfully cleared at step 2 since the IRQ
>>>> source was not cleared yet. So the PCIe host driver may receive the
>>>> same IRQ after step 5. Then there's an IRQ reentry occurred.
>>>> Even worse, if the reentry IRQ was not an IRQ that EP driver expected,
>>>> it may not handle the IRQ. Then we may run into the infinite loop from
>>>> step 2 to step 4.
>>>> Clear the IRQ status after IRQ have been dispatched to avoid the IRQ
>>>> reentry.
>>>> This patch also fix another INTx IRQ issue by initialize the iterate
>>>> before the loop. If an INTx IRQ re-occurred while we are dispatching
>>>> the INTx IRQ, then iterate may start from PCI_NUM_INTX + INTX_SHIFT
>>>> instead of INTX_SHIFT for the second time entering the
>>>> for_each_set_bit_from() loop.
>>>
>>> This looks like two different issues that should be fixed with two
>>> patches.
> 
> Ok, I split this into two patches and figure out a more reasonable
> approach by using irq_chip solution.
> 
>>>
>>>> Signed-off-by: Honghui Zhang <honghui.zhang@xxxxxxxxxxxx>
>>>> Acked-by: Ryder Lee <ryder.lee@xxxxxxxxxxxx>
>>>> ---
>>>>  drivers/pci/host/pcie-mediatek.c | 11 ++++++-----
>>>>  1 file changed, 6 insertions(+), 5 deletions(-)
>>>
>>> For the sake of uniformity, I first want to understand why this
>>> driver does not call:
>>>
>>> chained_irq_enter/exit()
>>>
>>> in the primary handler (mtk_pcie_intr_handler()).
>>>
>>> With the GIC as a primary interrupt controller we have not
>>> even figured out how current code can actually work without
>>> calling the chained_* API.
>>>
>>> I want to come up with a consistent handling of IRQ domains for
>>> all host bridges and any discrepancy should be explained.
>>
>> That's because this driver is a huge hack, see below:
>>
>>>
>>>> diff --git a/drivers/pci/host/pcie-mediatek.c b/drivers/pci/host/pcie-mediatek.c
>>>> index db93efd..fc29a9a 100644
>>>> --- a/drivers/pci/host/pcie-mediatek.c
>>>> +++ b/drivers/pci/host/pcie-mediatek.c
>>>> @@ -601,15 +601,16 @@ static irqreturn_t mtk_pcie_intr_handler(int irq, void *data)
>>
>> This function is not a chained irqchip, but an interrupt handler...
>>
>>>>  	struct mtk_pcie_port *port = (struct mtk_pcie_port *)data;
>>>>  	unsigned long status;
>>>>  	u32 virq;
>>>> -	u32 bit = INTX_SHIFT;
>>>> +	u32 bit;
>>>>  
>>>>  	while ((status = readl(port->base + PCIE_INT_STATUS)) & INTX_MASK) {
>>>> +		bit = INTX_SHIFT;
>>>>  		for_each_set_bit_from(bit, &status, PCI_NUM_INTX + INTX_SHIFT) {
>>>> -			/* Clear the INTx */
>>>> -			writel(1 << bit, port->base + PCIE_INT_STATUS);
>>>>  			virq = irq_find_mapping(port->irq_domain,
>>>>  						bit - INTX_SHIFT);
>>>>  			generic_handle_irq(virq);
>>
>> and nonetheless, this calls into generic_handle_irq(). That's a complete
>> violation of the interrupt layering. Maybe there is a good reason for
>> it, but I'd like to know which one.
>>
>> Which means that all of the ack/mask has to be done outside of the
>> irqchip framework too... Disgusting.
>>
>>>> +			/* Clear the INTx */
>>>> +			writel(1 << bit, port->base + PCIE_INT_STATUS);
>>>
>>> I think that these masking/acking should actually be done through
>>> the irq_chip hooks (see for instance pci-ftpci100.c) - that would
>>> make this kind of bugs much easier to prevent (because the IRQ
>>> layer does the sequencing for you).
>>
>> +1.
>>
> 
> Thanks for your advice, I need to do some homework to have a better
> understanding of the irq_chip approach.
> 
>>> Marc (CC'ed) has a more comprehensive view on this than me - I would
>>> like to get to a point where all host bridges uses a consistent
>>> approach for chained IRQ handling and I hope this bug fix can be
>>> a starting point.
>>
>> +1 again. We definitely need to come up with some form of common
>> approach for all these host drivers, and maybe turn that into a library...
>>
> 
> Well, this is beyond my knowledge now, I guess I can figure out how to
> using irq_chip for the first step, then I may following this "common
> approach" after we have a solution for that?

We can help you with that at a later time indeed. the urgent thing is to
fix this driver so that it does the right thing, and we can then look at
using a common approach for a number of them.

Thanks,

	M.
-- 
Jazz is not dead. It just smells funny...
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux