On Wed, 20 Dec 2017 12:06:45 -0600
Rob Herring <robh@xxxxxxxxxx> wrote:
> On Sat, Dec 16, 2017 at 07:35:37PM +0100, Boris Brezillon wrote:
> > On Sat, 16 Dec 2017 11:20:40 -0600
> > Rob Herring <robh@xxxxxxxxxx> wrote:
> >
> > > On Thu, Dec 14, 2017 at 04:16:08PM +0100, Boris Brezillon wrote:
> > > > A new I3C subsystem has been added and a generic description has been
> > > > created to represent the I3C bus and the devices connected on it.
> > > >
> > > > Document this generic representation.
>
> [...]
>
> > > So please define the node
> > > name to be "i3c-controller". That's more inline with other node names
> > > than i3c-master that you used below.
> >
> > Hm, not sure i3c-controller is appropriate though, because you can have
> > slave controllers. Maybe i3c-host, but I'd prefer to keep the term
> > master since it's employed everywhere in the spec. I can also be
> > i3c-master-controller if you prefer.
>
> Okay, i3c-master is fine. Just make it explicit.
Okay.
>
> > > > +I3C devices
> > > > +===========
> > > > +
> > > > +All I3C devices are supposed to support DAA (Dynamic Address Assignment), and
> > > > +are thus discoverable. So, by default, I3C devices do not have to be described
> > > > +in the device tree.
> > > > +This being said, one might want to attach extra resources to these devices,
> > > > +and those resources may have to be described in the device tree, which in turn
> > > > +means we have to describe I3C devices.
> > > > +
> > > > +Another use case for describing an I3C device in the device tree is when this
> > > > +I3C device has a static address and we want to assign it a specific dynamic
> > > > +address before the DAA takes place (so that other devices on the bus can't
> > > > +take this dynamic address).
> > > > +
> > > > +Required properties
> > > > +-------------------
> > > > +- i3c-pid: PID (Provisional ID). 64-bit property which is used to match a
> > > > + device discovered during DAA with its device tree definition. The
> > > > + PID is supposed to be unique on a given bus, which guarantees a 1:1
> > > > + match. This property becomes optional if a reg property is defined,
> > > > + meaning that the device has a static address.
> > >
> > > What determines this number?
> >
> > Part of it is fixed (manufacturer and part id) and the last few bits
> > represent the device instance on the bus (so you can have several
> > identical devices on the same bus). The manufacturer and part ids
> > should be statically assigned during production, instance id is usually
> > configurable through extra pins that you drive high or low at reset
> > time.
>
> Sounds like an I2C address at least for the pin strapping part...
The address space of this instance-id is smaller (4bits) than the I2C
one (7bits), and more importantly, the instance-id is not required to
be unique, it's the aggregation of the vendor-id, part-id and
instance-id that has to be unique. So, if you were thinking about using
this id to uniquely identify the device on the bus it's not a good idea.
>
> > > > +
> > > > +Optional properties
> > > > +-------------------
> > > > +- reg: static address. Only valid is the device has a static address.
> > > > +- i3c-dynamic-address: dynamic address to be assigned to this device. This
> > > > + property depends on the reg property.
> > >
> > > Perhaps "assigned-address" property would be appropriate. I'm not all
> > > that familiar with it though.
> >
> > Again, the spec use the term "dynamic address" everywhere, and I'd like
> > to stay as close as possible to the spec.
>
> I looked at assigned-addresses a bit more and that won't really fit
> because it should be the same format as reg. So I think reg should
> always be the PID as that is fixed and always present. Then the DAA
> address is separate and can be the i3c-dynamic-address property.
>
> However, there's still part I don't understand...
>
> > > > + /* I3C device with a static address. */
> > > > + thermal_sensor: sensor@68 {
> > > > + reg = <0x68>;
> > > > + i3c-dynamic-address = <0xa>;
>
> I'm confused as to how/why you have both reg and dynamic address?
Some I3C devices have an I2C address (also called static or legacy
address in a few places). The static/I2C/legacy address is used until
the I3C device is assigned a dynamic address by the master. The whole
point of specifying both an I2C address (through the reg property) and
a dynamic address (through the i3c-dynamic-address) is to tell the
controller that a specific dynamic address should be assigned to this
device using the SETSADA (Set Dynamic Address from Static Address)
command before a DAA (Dynamic Address Assignment) procedure is started.
This way, the device will not participate to the DAA (because it
already has a valid DA) and the dynamic address can't be assigned to
a different device (which is one of the problem with the automatic DAA
procedure).
>
> > > > + };
> > > > +
> > > > + /*
> > > > + * I3C device without a static address but requiring resources
> > > > + * described in the DT.
> > > > + */
> > > > + sensor2 {
> > >
> > > It's not great that we can't follow using generic node names. Maybe the
> > > PID can be used as the address? In USB for example, we use hub ports for
> > > DT addresses rather than USB addresses since those are dynamic.
> >
> > Hm, the problem is, we may have 2 numbering schemes here: one where reg
> > is used (reg representing the I2C/static address), and another one
> > where the PID is used.
> > If you're okay with mixing those 2 schemes, then I'm fine with that too.
>
> Mixing I2C devices and I3C devices, yes. But you need to mix in a single
> device? IOW, do I3C devices also have an I2C address?
Yes, some of them have both.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
