Hi,
On Tue, 19 Dec 2017 13:53:28 +0200
Sakari Ailus <sakari.ailus@xxxxxx> wrote:
> Hi Yong,
>
> On Thu, Jul 27, 2017 at 01:01:36PM +0800, Yong Deng wrote:
> > Add binding documentation for Allwinner V3s CSI.
> >
> > Signed-off-by: Yong Deng <yong.deng@xxxxxxxxxxxx>
>
> DT bindings should precede the driver.
OK.
>
> > ---
> > .../devicetree/bindings/media/sun6i-csi.txt | 49 ++++++++++++++++++++++
> > 1 file changed, 49 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/media/sun6i-csi.txt
> >
> > diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > new file mode 100644
> > index 0000000..f8d83f6
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt
> > @@ -0,0 +1,49 @@
> > +Allwinner V3s Camera Sensor Interface
> > +------------------------------
> > +
> > +Required properties:
> > + - compatible: value must be "allwinner,sun8i-v3s-csi"
>
> What are sun6i and sun8i? Is this device first present in sun6i SoCs,
> whereas you have only defined bindings for sun8i?
Yes, some sun6i SoCs has the almost same CSI module.
There is only V3s on my hand. So, I only tested it on V3s. But
some people work on the others.
>
> > + - reg: base address and size of the memory-mapped region.
> > + - interrupts: interrupt associated to this IP
> > + - clocks: phandles to the clocks feeding the CSI
> > + * ahb: the CSI interface clock
> > + * mod: the CSI module clock
> > + * ram: the CSI DRAM clock
> > + - clock-names: the clock names mentioned above
> > + - resets: phandles to the reset line driving the CSI
> > +
> > +- ports: A ports node with endpoint definitions as defined in
> > + Documentation/devicetree/bindings/media/video-interfaces.txt.
>
> Please document mandatory and optional endpoint properties relevant for the
> hardware.
I have added below commit in my v3:
Currently, the driver only support the parallel interface. So, a single port
node with one endpoint and parallel bus is supported.
>
> > +
> > +Example:
> > +
> > + csi1: csi@01cb4000 {
> > + compatible = "allwinner,sun8i-v3s-csi";
> > + reg = <0x01cb4000 0x1000>;
> > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&ccu CLK_BUS_CSI>,
> > + <&ccu CLK_CSI1_SCLK>,
> > + <&ccu CLK_DRAM_CSI>;
> > + clock-names = "ahb", "mod", "ram";
> > + resets = <&ccu RST_BUS_CSI>;
> > +
> > + port {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + /* Parallel bus endpoint */
> > + csi1_ep: endpoint {
> > + remote-endpoint = <&adv7611_ep>;
> > + bus-width = <16>;
> > + data-shift = <0>;
> > +
> > + /* If hsync-active/vsync-active are missing,
> > + embedded BT.656 sync is used */
> > + hsync-active = <0>; /* Active low */
> > + vsync-active = <0>; /* Active low */
> > + data-active = <1>; /* Active high */
> > + pclk-sample = <1>; /* Rising */
> > + };
> > + };
> > + };
> > +
>
> --
> Kind regards,
>
> Sakari Ailus
> e-mail: sakari.ailus@xxxxxx
Thanks,
Yong
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
