Add DT info for the stmmac ethernet MAC which found in the Amlogic's Meson-AXG SoC, also describe the ethernet pinctrl & clock information here. This is tested in the S400 dev board which use a RTL8211F PHY, and the pins connect to the 'eth_rgmii_y_pins' group. Reviewed-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx> Signed-off-by: Yixun Lan <yixun.lan@xxxxxxxxxxx> --- Changes in v2 since [1]: - rebase to kevin's v4.16/dt64 branch - add Neil's Reviewed-by - move clock info to board.dts instead of in soc.dtsi - drop "meson-axg-dwmac" compatible string, since we didn't use this we could re-add it later when we really need. - note: to make ethernet work properly,it depend on clock & pinctrl[2], to compile the DTS, the patch [3] is required. the code part will be taken via clock & pinctrl subsystem tree. [1] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005301.html [2] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005735.html http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005694.html [3] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005738.html --- arch/arm64/boot/dts/amlogic/meson-axg-s400.dts | 11 ++++++ arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 50 ++++++++++++++++++++++++++ 2 files changed, 61 insertions(+) diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts b/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts index 70eca1f8736a..138de3bc7cc8 100644 --- a/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts +++ b/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts @@ -20,3 +20,14 @@ &uart_AO { status = "okay"; }; + +ðmac { + status = "okay"; + clocks = <&clkc CLKID_ETH>, + <&clkc CLKID_FCLK_DIV2>, + <&clkc CLKID_MPLL2>; + clock-names = "stmmaceth", "clkin0", "clkin1"; + phy-mode = "rgmii"; + pinctrl-0 = <ð_rgmii_y_pins>; + pinctrl-names = "default"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi index d356ce74ad89..106234fda765 100644 --- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi @@ -7,6 +7,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/irq.h> #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/axg-clkc.h> / { compatible = "amlogic,meson-axg"; @@ -148,6 +149,15 @@ #address-cells = <0>; }; + ethmac: ethernet@ff3f0000 { + compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac"; + reg = <0x0 0xff3f0000 0x0 0x10000 + 0x0 0xff634540 0x0 0x8>; + interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "macirq"; + status = "disabled"; + }; + hiubus: bus@ff63c000 { compatible = "simple-bus"; reg = <0x0 0xff63c000 0x0 0x1c00>; @@ -194,6 +204,46 @@ #gpio-cells = <2>; gpio-ranges = <&pinctrl_periphs 0 0 86>; }; + + eth_rgmii_x_pins: eth-x-rgmii { + mux { + groups = "eth_mdio_x", + "eth_mdc_x", + "eth_rgmii_rx_clk_x", + "eth_rx_dv_x", + "eth_rxd0_x", + "eth_rxd1_x", + "eth_rxd2_rgmii", + "eth_rxd3_rgmii", + "eth_rgmii_tx_clk", + "eth_txen_x", + "eth_txd0_x", + "eth_txd1_x", + "eth_txd2_rgmii", + "eth_txd3_rgmii"; + function = "eth"; + }; + }; + + eth_rgmii_y_pins: eth-y-rgmii { + mux { + groups = "eth_mdio_y", + "eth_mdc_y", + "eth_rgmii_rx_clk_y", + "eth_rx_dv_y", + "eth_rxd0_y", + "eth_rxd1_y", + "eth_rxd2_rgmii", + "eth_rxd3_rgmii", + "eth_rgmii_tx_clk", + "eth_txen_y", + "eth_txd0_y", + "eth_txd1_y", + "eth_txd2_rgmii", + "eth_txd3_rgmii"; + function = "eth"; + }; + }; }; }; -- 2.15.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
