On 2017/11/22 21:04, Jean-Philippe Brucker wrote: > On 22/11/17 03:15, Bob Liu wrote: >> Hey Jean, >> >> On 2017/10/6 21:31, Jean-Philippe Brucker wrote: >>> IOMMU drivers need a way to bind Linux processes to devices. This is used >>> for Shared Virtual Memory (SVM), where devices support paging. In that >>> mode, DMA can directly target virtual addresses of a process. >>> >>> Introduce boilerplate code for allocating process structures and binding >>> them to devices. Four operations are added to IOMMU drivers: >>> >>> * process_alloc, process_free: to create an iommu_process structure and >>> perform architecture-specific operations required to grab the process >>> (for instance on ARM SMMU, pin down the CPU ASID). There is a single >>> iommu_process structure per Linux process. >>> >> >> I'm a bit confused here. >> The original meaning of iommu_domain is a virtual addrspace defined by a set of io page table. >> (fix me if I misunderstood). > > iommu_domain can also be seen as a logical partition of devices that share > the same address spaces (the concept comes from AMD and Intel IOMMU > domains, I believe). Without PASIDs it was a single address space, with > PASIDs it can have multiple address spaces. > >> Then what's the meaning of iommu_domain and iommu_process after introducing iommu_process? >> Could you consider document these concepts? > > iommu_process is used to keep track of Linux process address spaces. I'll > rename it to io_mm in next version, to make it clear that it doesn't > represent a Linux task but an mm_struct instead. However the > implementation stays pretty much identical. A domain can be associated to > multiple io_mm, and an io_mm can be associated to multiple domains. > > In the IOMMU architectures I know, PASID is implemented like this. You > have the device tables (stream tables on SMMU), pointing to PASID tables > (context descriptor tables on SMMU). In the following diagram, > > .->+--------+ > / 0 | |------ io_pgtable > / +--------+ > / 1 | |------ io_mm->mm X > +--------+ / +--------+ > 0 | A |-' 2 | |-. > +--------+ +--------+ \ > 1 | | 3 | | \ > +--------+ +--------+ -- io_mm->mm Y > 2 | B |--. PASID tables / > +--------+ \ | > 3 | B |----+--->+--------+ | > +--------+ / 0 | |- | -- io_pgtable > 4 | B |--' +--------+ | > +--------+ 1 | | | > Device tables +--------+ | > 2 | |--' > +--------+ > 3 | |------ io_mm->priv io_pgtable > +--------+ > PASID tables > > * Device 0 (e.g. PCI 0000:00:00.0) is in domain A. > * Devices 2, 3 and 4 are in domain B. > * Domain A has the top set of PASID tables. > * Domain B has the bottom set of PASID tables. > > * Domain A is bound to process address space X. > -> Device 0 can access X with PASID 1. > * Both domains A and B are bound to process address space Y. > -> Devices 0, 2, 3 and 4 can access Y with PASID 2 > > * PASID 0 is special on Arm SMMU (with S1DSS=0b10). It will always be > reserved for classic DMA map/unmap. Even for hypothetical devices that > don't support non-pasid transactions, I'd like to keep this convention. > It should be quite useful for device drivers to have PASID 0 available > with DMA map/unmap. > > * When introducing "private" PASID address spaces (that many are asking > for), which are backed by a set of io-pgtable and map/unmap ops, I > suppose they would reuse the io_mm structure. In this example PASID 3 is > associated to a private address space and not backed by an mm. Since the > PASID space is global, PASID 3 won't be available for any other domain. > > Does this clarify the current design, or is it just more confusing? > It's very helpful, thank you very much! Regards, Liubo -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
