On Sun 19 Nov 13:35 PST 2017, Jacek Anaszewski wrote:
> Hi Bjorn,
>
> Thanks for the update.
>
> On 11/15/2017 08:13 AM, Bjorn Andersson wrote:
> > This adds the binding document describing the three hardware blocks
> > related to the Light Pulse Generator found in a wide range of Qualcomm
> > PMICs.
> >
> > Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> > ---
> >
> > Changes since v2:
> > - Squashed all things into one node
> > - Removed quirks from the binding, compatible implies number of channels, their
> > configuration etc.
> > - Binding describes LEDs connected as child nodes
> > - Support describing multi-channel LEDs
> > - Change style of the binding document, to match other LED bindings
> >
> > Changes since v1:
> > - Dropped custom pattern properties
> > - Renamed cell-index to qcom,lpg-channel to clarify its purpose
> >
> > .../devicetree/bindings/leds/leds-qcom-lpg.txt | 66 ++++++++++++++++++++++
> > 1 file changed, 66 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/leds/leds-qcom-lpg.txt
> >
> > diff --git a/Documentation/devicetree/bindings/leds/leds-qcom-lpg.txt b/Documentation/devicetree/bindings/leds/leds-qcom-lpg.txt
> > new file mode 100644
> > index 000000000000..9cee6f9f543c
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/leds/leds-qcom-lpg.txt
> > @@ -0,0 +1,66 @@
> > +Binding for Qualcomm Light Pulse Generator
> > +
> > +The Qualcomm Light Pulse Generator consists of three different hardware blocks;
> > +a ramp generator with lookup table, the light pulse generator and a three
> > +channel current sink. These blocks are found in a wide range of Qualcomm PMICs.
> > +
> > +Required properties:
> > +- compatible: one of:
> > + "qcom,pm8916-pwm",
> > + "qcom,pm8941-lpg",
> > + "qcom,pm8994-lpg",
> > + "qcom,pmi8994-lpg",
> > + "qcom,pmi8998-lpg",
> > +
> > +Optional properties:
> > +- qcom,power-source: power-source used to drive the output, as defined in the
> > + datasheet. Should be specified if the TRILED block is
> > + present
>
> Range of possible values is missing here.
>
There seems to be a 4-way mux in all variants, but the wiring is
different in the different products. E.g. in pm8941 1 represents VPH_PWR
while in pmi8994 this is pulled from a dedicated pin named VIN_RGB.
Would you like me to list the 4 options for each compatible?
> > +- qcom,dtest: configures the output into an internal test line of the
> > + pmic. Specified by a list of u32 pairs, one pair per channel,
> > + where each pair denotes the test line to drive and the second
> > + configures how the value should be outputed, as defined in the
> > + datasheet
> > +- #pwm-cells: should be 2, see ../pwm/pwm.txt
> > +
> > +LED subnodes:
> > +A set of subnodes can be used to specify LEDs connected to the LPG. Channels
> > +not associated with a LED are available as pwm channels, see ../pwm/pwm.txt.
> > +
> > +Required properties:
> > +- led-sources: list of channels associated with this LED, starting at 1 for the
> > + first LPG channel
> > +
> > +Optional properties:
> > +- label: see Documentation/devicetree/bindings/leds/common.txt
> > +- default-state: see Documentation/devicetree/bindings/leds/common.txt
> > +- linux,default-trigger: see Documentation/devicetree/bindings/leds/common.txt
> > +
> > +Example:
> > +The following example defines a RGB LED attached to the PM8941.
> > +
> > +&spmi_bus {
> > + pm8941@1 {
> > + lpg {
> > + compatible = "qcom,pm8941-lpg";
> > + qcom,power-source = <1>;
> > +
> > + rgb {
> > + led-sources = <7 6 5>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +The following example defines the single PWM channel of the PM8916, which can
> > +be muxed by the MPP4 as a current sink.
> > +
> > +&spmi_bus {
> > + pm8916@1 {
> > + pm8916_pwm: pwm {
> > + compatible = "qcom,pm8916-pwm";
> > +
> > + #pwm-cells = <2>;
>
> LED has to be represented as a child node -
> see Documentation/devicetree/bindings/leds/common.txt
>
Some use cases for this hardware block is to use it as a "traditional"
PWM source, so any channels not allocated to a LED are available as pwm
channels.
So this is from the Dragonboard410c, where the example application is to
wire this pwm signal as control signal to a backlight controller; i.e.
using pwm-backlight associated with the display panel.
For testing purposes I did route the signal to another gpio with a LED
on the board, added a LED node here and saw that I can control that as
well.
I did include this example here, even though there's no LED, just to
show how this could be done.
> > + };
> > + };
> > +};
> >
>
> Could you please also provide an example of the arrangement on the
> board DragonBoard820c, you were describing in the discussions under
> the previous version of the patch set. i.e. three green LEDs connected
> to TRILED and one to the GPIO sink?
>
Of course.
> Also any other non-trivial board configurations supported by the
> driver would allow to increase our comprehensions of the device
> capabilities.
>
There is a few other hardware components that can be fed the output of
the LPG as control signal, but I think the GPIO sink case above does
showcase the power.
Regards,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
