> -----Original Message----- > From: Leo Li > Sent: Saturday, November 11, 2017 5:21 AM > To: Kishon Vijay Abraham I <kishon@xxxxxx>; Xiaowei Bao > <xiaowei.bao@xxxxxxx>; robh+dt@xxxxxxxxxx; mark.rutland@xxxxxxx; > catalin.marinas@xxxxxxx; will.deacon@xxxxxxx; bhelgaas@xxxxxxxxxx; > shawnguo@xxxxxxxxxx; Madalin-cristian Bucur <madalin.bucur@xxxxxxx>; > Sumit Garg <sumit.garg@xxxxxxx>; Y.b. Lu <yangbo.lu@xxxxxxx>; Andy Tang > <andy.tang@xxxxxxx>; jingoohan1@xxxxxxxxx; pbrobinson@xxxxxxxxx; > songxiaowei@xxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; linux-arm- > kernel@xxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; linux- > pci@xxxxxxxxxxxxxxx; linuxppc-dev@xxxxxxxxxxxxxxxx; Z.q. Hou > <zhiqiang.hou@xxxxxxx>; Mingkai Hu <mingkai.hu@xxxxxxx>; M.h. Lian > <minghuan.lian@xxxxxxx> > Subject: RE: [PATCHv4 1/3] ARMv8: dts: ls1046a: add the property of IB and OB > > > > > -----Original Message----- > > From: Kishon Vijay Abraham I [mailto:kishon@xxxxxx] > > Sent: Friday, November 10, 2017 12:22 AM > > To: Xiaowei Bao <xiaowei.bao@xxxxxxx>; robh+dt@xxxxxxxxxx; > > mark.rutland@xxxxxxx; catalin.marinas@xxxxxxx; will.deacon@xxxxxxx; > > bhelgaas@xxxxxxxxxx; shawnguo@xxxxxxxxxx; Madalin-cristian Bucur > > <madalin.bucur@xxxxxxx>; Sumit Garg <sumit.garg@xxxxxxx>; Y.b. Lu > > <yangbo.lu@xxxxxxx>; hongtao.jia@xxxxxxx; Andy Tang > > <andy.tang@xxxxxxx>; Leo Li <leoyang.li@xxxxxxx>; > > jingoohan1@xxxxxxxxx; pbrobinson@xxxxxxxxx; songxiaowei@xxxxxxxxxxxxx; > > devicetree@xxxxxxxxxxxxxxx; linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; > > linux- kernel@xxxxxxxxxxxxxxx; linux-pci@xxxxxxxxxxxxxxx; linuxppc- > > dev@xxxxxxxxxxxxxxxx; Z.q. Hou <zhiqiang.hou@xxxxxxx>; Mingkai Hu > > <mingkai.hu@xxxxxxx>; M.h. Lian <minghuan.lian@xxxxxxx> > > Subject: Re: [PATCHv4 1/3] ARMv8: dts: ls1046a: add the property of IB > > and OB > > > > Hi Bao, > > > > On Friday 10 November 2017 09:18 AM, Bao Xiaowei wrote: > > > Add the property of inbound and outbound windows number for ep driver. > > > > > > Signed-off-by: Bao Xiaowei <xiaowei.bao@xxxxxxx> > > > Acked-by: Minghuan Lian <minghuan.Lian@xxxxxxx> > > > --- > > > v2: > > > - no change > > > v3: > > > - modify the commit message > > > v4: > > > - no change > > > > > > arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 6 ++++++ > > > 1 file changed, 6 insertions(+) > > > > $subject should start with something like > > arm64: dts: ls1046a: ** > > > > > > diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi > > > b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi > > > index 06b5e12d04d8..f8332669663c 100644 > > > --- a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi > > > +++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi > > > @@ -674,6 +674,8 @@ > > > device_type = "pci"; > > > dma-coherent; > > > num-lanes = <4>; > > > + num-ib-windows = <6>; > > > + num-ob-windows = <6>; > > > > EP specific properties shouldn't be added in RC dt node. Ideally you > > should have a separate dt node for RC and EP. > > It is a single PCIe controller which can be configured to either RC mode or EP > mode. Wouldn't it conflict with the device tree principles to have two device > tree nodes for the same PCIe controller? And obviously the two modes cannot > be used at the same time so we cannot have two drivers both probe on the > same hardware. > [Minghuan Lian] There is only one PCIe dts node in the dts file. PCIe dts node describes the PCIe controller's hardware properties and does not have work mode. The new properties "num-ib-windows " and "num-ob-windows" are used to describe the inbound/outbound window number included in the PCIe hardware. These windows are used in both RC and EP mode. We can change work mode when resetting via RCW(reset configuration word). > Regards, > Leo -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
