[PATCH v4] ARM: dts: display5: Device tree description of LWN's DISPLAY5 board

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




This commit adds device tree description of Liebherr's Display5 board.

Signed-off-by: Lukasz Majewski <lukma@xxxxxxx>
Reviewed-by: Fabio Estevam <fabio.estevam@xxxxxxx>

---
Changes for v2:

- Postpone adding Mitsubishi display
- Replace GPL with dual GPL/X11 licenses
- Remove superfluous "i2s-master" property
- Replace pinctrl 0x80000000 value (meaning that this ping shall not be
  configured in Linux) with proper values (set by bootloader)

Changes for v3:
- Add "nxp,tfa9879" compatible for sound codec
- Remove not needed "pinctrl-names"
- Change the patch topic line

Changes for v4:
- Remove not needed dr_mode = "host"; (defined earlier)
- Move pinctrl-0 = <&pinctrl_usbh1>; to proper place
---
 arch/arm/boot/dts/Makefile                         |   1 +
 .../dts/imx6q-display5-tianma-tm070-1280x768.dts   |  51 ++
 arch/arm/boot/dts/imx6q-display5.dtsi              | 596 +++++++++++++++++++++
 3 files changed, 648 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
 create mode 100644 arch/arm/boot/dts/imx6q-display5.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index faf46ab..d9d0c82 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -407,6 +407,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-cm-fx6.dtb \
 	imx6q-cubox-i.dtb \
 	imx6q-dfi-fs700-m60.dtb \
+	imx6q-display5-tianma-tm070-1280x768.dtb \
 	imx6q-dmo-edmqmx6.dtb \
 	imx6q-evi.dtb \
 	imx6q-gk802.dtb \
diff --git a/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts b/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
new file mode 100644
index 0000000..16658b7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
@@ -0,0 +1,51 @@
+/*
+ * Copyright 2017
+ * Lukasz Majewski, DENX Software Engineering, lukma@xxxxxxx
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q-display5.dtsi"
+
+&panel {
+	compatible = "tianma,tm070jdhg30";
+};
+
+&ldb {
+	lvds0: lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <18>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-display5.dtsi b/arch/arm/boot/dts/imx6q-display5.dtsi
new file mode 100644
index 0000000..5de337d
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-display5.dtsi
@@ -0,0 +1,596 @@
+/*
+ * Copyright 2017
+ * Lukasz Majewski, DENX Software Engineering, lukma@xxxxxxx
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+	model = "Liebherr (LWN) display5 i.MX6 Quad Board";
+	compatible = "lwn,display5", "fsl,imx6q";
+
+	memory {
+		reg = <0x10000000 0x40000000>;
+	};
+
+	backlight_lvds: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		pwms = <&pwm2 0 5000000 0>;
+		brightness-levels = <  0   1   2   3   4   5   6   7   8   9
+				      10  11  12  13  14  15  16  17  18  19
+				      20  21  22  23  24  25  26  27  28  29
+				      30  31  32  33  34  35  36  37  38  39
+				      40  41  42  43  44  45  46  47  48  49
+				      50  51  52  53  54  55  56  57  58  59
+				      60  61  62  63  64  65  66  67  68  69
+				      70  71  72  73  74  75  76  77  78  79
+				      80  81  82  83  84  85  86  87  88  89
+				      90  91  92  93  94  95  96  97  98  99
+				     100 101 102 103 104 105 106 107 108 109
+				     110 111 112 113 114 115 116 117 118 119
+				     120 121 122 123 124 125 126 127 128 129
+				     130 131 132 133 134 135 136 137 138 139
+				     140 141 142 143 144 145 146 147 148 149
+				     150 151 152 153 154 155 156 157 158 159
+				     160 161 162 163 164 165 166 167 168 169
+				     170 171 172 173 174 175 176 177 178 179
+				     180 181 182 183 184 185 186 187 188 189
+				     190 191 192 193 194 195 196 197 198 199
+				     200 201 202 203 204 205 206 207 208 209
+				     210 211 212 213 214 215 216 217 218 219
+				     220 221 222 223 224 225 226 227 228 229
+				     230 231 232 233 234 235 236 237 238 239
+				     240 241 242 243 244 245 246 247 248 249
+				     250 251 252 253 254 255>;
+		default-brightness-level = <250>;
+		enable-gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_lvds: regulator-lvds {
+		compatible = "regulator-fixed";
+		regulator-name = "lvds_ppen";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_lvds>;
+		gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usbh1_vbus: usb-h1-vbus {
+		compatible = "regulator-fixed";
+		gpio = <&gpio3 31 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1_vbus>;
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-enable-ramp-delay = <300000>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		label = "tfa9879-mono";
+
+		simple-audio-card,dai-link {
+			/* DAC */
+			format = "i2s";
+			bitclock-master = <&dailink_master>;
+			frame-master = <&dailink_master>;
+
+			dailink_master: cpu {
+			    sound-dai = <&ssi2>;
+			};
+			codec {
+			    sound-dai = <&codec>;
+			};
+		};
+	};
+
+	panel: panel-lvds0 {
+		backlight = <&backlight_lvds>;
+		power-supply = <&reg_lvds>;
+
+		port {
+			panel_in_lvds0: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+
+	ssi2 {
+		fsl,audmux-port = <1>;
+		fsl,port-config = <
+			(IMX_AUDMUX_V2_PTCR_SYN |
+			 IMX_AUDMUX_V2_PTCR_TFSEL(5) |
+			 IMX_AUDMUX_V2_PTCR_TCSEL(5) |
+			 IMX_AUDMUX_V2_PTCR_TFSDIR |
+			 IMX_AUDMUX_V2_PTCR_TCLKDIR)
+			IMX_AUDMUX_V2_PDCR_RXDSEL(5)
+		>;
+	};
+
+	aud6 {
+		fsl,audmux-port = <5>;
+		fsl,port-config = <
+			(IMX_AUDMUX_V2_PTCR_RFSEL(8) |
+			 IMX_AUDMUX_V2_PTCR_RCSEL(8) |
+			 IMX_AUDMUX_V2_PTCR_TFSEL(1) |
+			 IMX_AUDMUX_V2_PTCR_TCSEL(1) |
+			 IMX_AUDMUX_V2_PTCR_RFSDIR |
+			 IMX_AUDMUX_V2_PTCR_RCLKDIR |
+			 IMX_AUDMUX_V2_PTCR_TFSDIR |
+			 IMX_AUDMUX_V2_PTCR_TCLKDIR)
+			IMX_AUDMUX_V2_PDCR_RXDSEL(1)
+		>;
+	};
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs &pinctrl_ecspi2_flwp>;
+	status = "okay";
+
+	s25fl256s: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <40000000>;
+		reg = <0>;
+
+		partition@0 {
+			label = "SPL (spi)";
+			reg = <0x0 0x20000>;
+			read-only;
+		};
+		partition@1 {
+			label = "u-boot (spi)";
+			reg = <0x20000 0x100000>;
+			read-only;
+		};
+		partition@2 {
+			label = "uboot-env (spi)";
+			reg = <0x120000 0x10000>;
+		};
+		partition@3 {
+			label = "uboot-envr (spi)";
+			reg = <0x130000 0x10000>;
+		};
+		partition@4 {
+			label = "linux-recovery (spi)";
+			reg = <0x140000 0x800000>;
+		};
+		partition@5 {
+			label = "swupdate-fitImg (spi)";
+			reg = <0x940000 0x400000>;
+		};
+		partition@6 {
+			label = "swupdate-initramfs (spi)";
+			reg = <0xD40000 0x800000>;
+		};
+	};
+};
+
+&ecspi3 {
+	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs &pinctrl_ecspi3_flwp>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-handle = <&ethernet_phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		ethernet_phy0: ethernet-phy@0 {
+			compatible = "marvell,88E1510";
+			device_type = "ethernet-phy";
+			/* Set LED0 control: */
+			/* On - Link, Blink - Activity, Off - No Link */
+			marvell,reg-init = <3 0x10 0 0x1011>;
+			max-speed = <100>;
+			reg = <0>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: tfa9879@6C {
+		#sound-dai-cells = <0>;
+		compatible = "nxp,tfa9879";
+		reg = <0x6C>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	at24@50 {
+		compatible = "atmel,24c256";
+		pagesize = <64>;
+		reg = <0x50>;
+	};
+
+	pfuze100: pmic@08 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw1c_reg: sw1c {
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3a_reg: sw3a {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw3b_reg: sw3b {
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			sw4_reg: sw4 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&ldb {
+	status = "okay";
+
+	lvds0: lvds-channel@0 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in_lvds0>;
+			};
+		};
+	};
+};
+
+&pwm2 {
+	#pwm-cells = <3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&ssi2 {
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usbh1_vbus>;
+	pinctrl-0 = <&pinctrl_usbh1>;
+	status = "okay";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			/* I2S OUTPUT AUD6*/
+			MX6QDL_PAD_DI0_PIN4__AUD6_RXD  0x130b0
+			MX6QDL_PAD_DI0_PIN2__AUD6_TXD  0x130b0
+			MX6QDL_PAD_DI0_PIN3__AUD6_TXFS  0x130b0
+			MX6QDL_PAD_DI0_PIN15__AUD6_TXC  0x130b0
+		>;
+	};
+
+	pinctrl_backlight: dispgrp {
+		fsl,pins = <
+			/* BLEN_OUT */
+			MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07    0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO	0x100b1
+			MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI	0x100b1
+			MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK	0x100b1
+		>;
+	};
+
+	pinctrl_ecspi2_cs: ecspi2csgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x100b1
+		>;
+	};
+
+	pinctrl_ecspi2_flwp: ecspi2flwpgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
+			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
+			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
+		>;
+	};
+
+	pinctrl_ecspi3_cs: ecspi3csgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi3_flwp: ecspi3flwpgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x1b0b0
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b0b0
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
+			MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
+			MX6QDL_PAD_ENET_RXD0__GPIO1_IO27        0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__I2C1_SCL	0x4001b8b1
+			MX6QDL_PAD_EIM_D28__I2C1_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_EB2__I2C2_SCL	0x4001b8b1
+			MX6QDL_PAD_EIM_D16__I2C2_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__I2C3_SCL	0x4001b8b1
+			MX6QDL_PAD_EIM_D18__I2C3_SDA	0x4001b8b1
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT9__PWM2_OUT	0x1b0b1
+		>;
+	};
+
+	pinctrl_reg_lvds: reqlvdsgrp {
+		fsl,pins = <
+			/* LVDS_PPEN_OUT */
+			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13      0x1b0b0
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA	0x1b0b1
+			MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA    0x1b0b1
+		>;
+	};
+
+	pinctrl_usbh1: usbh1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D30__USB_H1_OC  0x030b0
+		>;
+	};
+
+	pinctrl_usbh1_vbus: usbh1_vbus_grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
+			MX6QDL_PAD_NANDF_ALE__SD4_RESET	0x17059
+		>;
+	};
+};
-- 
2.1.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux