On Wed, Oct 18, 2017 at 11:17 AM, Bjorn Helgaas <helgaas@xxxxxxxxxx> wrote: > On Tue, Oct 17, 2017 at 04:39:05PM -0700, Brian Norris wrote: >> On Fri, Oct 13, 2017 at 11:51:52AM -0500, Bjorn Helgaas wrote: >> > On Thu, Oct 12, 2017 at 01:52:18PM -0700, Brian Norris wrote: >> > > The patch is self-descriptive. I've found that we may need >> > > platform-specific behavior for the PERST# signal in system suspend, >> > > depending on the type of PCIe endpoints are attached. >> > > >> > > Signed-off-by: Brian Norris <briannorris@xxxxxxxxxxxx> >> > > --- >> > > Documentation/devicetree/bindings/pci/pci.txt | 11 +++++++++++ >> > > 1 file changed, 11 insertions(+) >> > > >> > > diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt >> > > index c77981c5dd18..91339b6d0652 100644 >> > > --- a/Documentation/devicetree/bindings/pci/pci.txt >> > > +++ b/Documentation/devicetree/bindings/pci/pci.txt >> > > @@ -24,3 +24,14 @@ driver implementation may support the following properties: >> > > unsupported link speed, for instance, trying to do training for >> > > unsupported link speed, etc. Must be '4' for gen4, '3' for gen3, '2' >> > > for gen2, and '1' for gen1. Any other values are invalid. >> > > +- pcie-reset-suspend: >> > > + If present this property defines whether the PCIe Reset signal (referred to >> > > + as PERST#) should be asserted when the system enters low-power suspend modes >> > > + (e.g., S3). Depending on the form factor, the associated PCIe >> > > + electromechanical specification may specify a particular behavior (e.g., >> > > + "PERST# is asserted in advance of the power being switched off in a >> > > + power-managed state like S3") or it may be less clear. The net result is >> > > + that some endpoints perform better (e.g., lower power consumption) with >> > > + PERST# asserted, and others prefer PERST# deasserted. The value must be '0' >> > > + or '1', where '0' means do not assert PERST# and '1' means assert PERST#. >> > > + When absent, behavior may be platform-specific. >> > >> > I don't understand this at all. Are you suggesting that we need >> > different "pcie-reset-suspend" values based on what sort of endpoint >> > the user plugs in? >> >> Partly. I guess I also failed to mention in this particular text (but I >> did, in patch 3) that it can be a board-specific problem, related to the >> fact that the only endpoint used on said board--soldered on, not >> replaceable--never seemed to require PERST# to be asserted in suspend. >> On such boards, I believe [1] it is physically impossible to drive this >> pin low in S3 suspend. So even if we tried to assert PERST#, it would >> pull back up when we suspend the system. I'm not sure if that's better >> or worse than not asserting it at all. >> >> So, that's why I settled on a device tree property. It describes the >> physical ability of the board too, in some cases. (I could document this >> better, I see.) > > It would make sense to me to have a DT property in the PCIe host > controller object that describes how that controller works, including > its capabilities with respect to PERST#, assuming there's a reasonable > way to use that information. > > If there's a DT way to describe a hard-wired PCIe endpoint, it might > make sense to have a second property in the endpoint object that > describes its preferences. Obviously this couldn't apply to slots > where we don't know what might be plugged in. That's implicit with having an endpoint described in DT though true OF would have every device present. Rob -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
