Hi Andrzej,
On Wednesday, 18 October 2017 18:11:25 EEST Laurent Pinchart wrote:
> On Thursday, 28 September 2017 16:07:27 EEST Andrzej Hajda wrote:
> > These bindings allows to describe most known standard USB connectors
> > and it should be possible to extend it if necessary.
> > USB connectors, beside USB can be used to route other protocols,
> > for example UART, Audio, MHL. In such case every device passing data
> > through the connector should have appropriate graph bindings.
> >
> > Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
> > ---
> > There are few things for discussion (IMO):
> > 1. vendor specific connectors, I have added them here, but maybe better is
> >
> > to place them in separate files.
>
> It's useful to have one vendor-specific compatible string to be used in the
> example. We could split vendor-specific connectors to separate files later
> if needed, but for now I'm fine keeping them here.
>
> > 2. physical connector description - I have split it to three properties:
> > type(a,b,ab,c), max-mode(ls,fs,hs,ss,ss+), size(mini,micro,powered).
> > This tripled is able to describe all USB-standard connectors, but there
> > are also impossible combinations, for example(c, *, micro). Maybe
> > better
> > would be to just enumerate all possible connectors in include file.
>
> I don't have a strong opinion on this. The three properties are nicely
> descriptive. You might want to list the valid combinations in the bindings
> though.
>
> > 3. Numbering of port/remote nodes, currently only 0 is assigned for
> >
> > Interface Controller. Maybe other functions should be also assigned:
> > HS, SS, CC, SBU, ... whatever. Maybe functions should be described
> > as an additional property of remote node?
>
> Given that one of the main reasons this binding is needed is to describe MHL
> connection to a USB connector, I think we'll need to define additional
> functions, yes. I'm not sure yet how that should look like though.
> > ---
> >
> > .../bindings/connector/usb-connector.txt | 49 +++++++++++++++++
> > 1 file changed, 49 insertions(+)
> > create mode 100644
> >
> > Documentation/devicetree/bindings/connector/usb-connector.txt
> >
> > diff --git a/Documentation/devicetree/bindings/connector/usb-connector.txt
> > b/Documentation/devicetree/bindings/connector/usb-connector.txt new file
> > mode 100644
> > index 000000000000..f3a4e85122d5
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/connector/usb-connector.txt
> > @@ -0,0 +1,49 @@
> > +USB Connector
> > +=============
> > +
> > +Required properties:
> > +- compatible: "usb-connector"
> > + connectors with vendor specific extensions can add one of additional
> > + compatibles:
> > + "samsung,usb-connector-11pin": 11-pin Samsung micro-USB connector
> > +- type: the USB connector type: "a", "b", "ab", "c"
> > +- max-mode: max USB speed mode supported by the connector:
> > + "ls", "fs", "hs", "ss", "ss+"
> > +
> > +Optional properties:
> > +- label: a symbolic name for the connector
> > +- size: size of the connector, should be specified in case of
> > + non-standard USB connectors: "mini", "micro", "powered"
>
> "non-standard" sounds like "vendor-specific", while I assume you're talking
> about the size. The USB specification uses the term "standard" for this
> purpose, so it's hard to use another one that would convey the right meaning
> precisely. Maybe "non-standard ('large') USB connector sizes" ?
>
> > +Required nodes:
> > +- any data bus to the connector should be modeled using the
> > + OF graph bindings specified in bindings/graph.txt.
> > + There should be exactly one port with at least one endpoint to
> > + different device nodes. The first endpoint (reg = <0>) should
> > + point to USB Interface Controller.
> > +
> > +Example
> > +-------
> > +
> > +musb_con: connector {
> > + compatible = "samsung,usb-connector-11pin", "usb-connector";
> > + label = "usb";
> > + type = "b";
> > + size = "micro";
> > + max-mode = "hs";
> > +
> > + port {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + musb_con_usb_in: endpoint@0 {
> > + reg = <0>;
> > + remote-endpoint = <&muic_usb_out>;
> > + };
> > +
> > + musb_con_mhl_in: endpoint@1 {
> > + reg = <1>;
> > + remote-endpoint = <&mhl_out>;
> > + };
> > + };
> > +};
One more comment, do I assume correctly that the Samsung 11-pin connector
carries USB and MHL on different pins ?
--
Regards,
Laurent Pinchart
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
