On Mon, Oct 02, 2017 at 02:35:08PM +0200, Jerome Brunet wrote: > On Sun, 2017-10-01 at 22:32 +0200, Martin Blumenstingl wrote: > > Hello Greg, Hello Mathias, > > > > On Mon, Sep 18, 2017 at 10:49 AM, Greg KH <gregkh@xxxxxxxxxxxxxxxxxxx> wrote: > > > On Sun, Sep 17, 2017 at 10:51:31PM +0200, Martin Blumenstingl wrote: > > > > Hello Mathias, Hello Greg, > > > > > > > > On Sun, Sep 3, 2017 at 11:38 PM, Martin Blumenstingl > > > > <martin.blumenstingl@xxxxxxxxxxxxxx> wrote: > > > > > This series is the outcome of a discussion with Felipe Balbi, > > > > > see [0] and [1]. > > > > > The quick-summary of this is: > > > > > - dwc3 already takes one USB2 and one USB3 PHY and initializes these > > > > > correct > > > > > - some other HCI platform drivers (like ehci-platform.c, xhci-mtk.c and > > > > > ohci-platform.c) do not have a limitation on the number of PHYs - they > > > > > support one PHY per actual host port > > > > > - Amlogic Meson GXL and GXM SoCs come with a dwc3 IP block which has two > > > > > or three USB2 ports enabled on the internal root-hub. The SoCs also > > > > > provide separate USB2 PHYs, one per port. All USB2 PHYs (which are > > > > > internally "connected" to the dwc3 roothub) need to be powered on, > > > > > otherwise USB devices cannot be enumerated (even if just one PHY is > > > > > disabled and if the device is plugged into another, enabled port) > > > > > > > > > > In my first attempt to get USB supported on the GXL and GXM SoCs I tried > > > > > to work-around the problem that I could not pass multiple PHYs to the > > > > > dwc3 controller. > > > > > This was rejected by Rob Herring (which was definitely the thing to do > > > > > in > > > > > my opinion), see [2] > > > > > > > > > > This series adds a new "platform-roothub". This can be configured > > > > > through > > > > > devicetree by passing a child-node with "reg = <0>" to the USB > > > > > controller. Additionally there has to be a child-node for each port on > > > > > the root-hub. Each of the child-nodes takes a "phys" and "phy-names" > > > > > property. This allows modeling the root-hub in devicetree similar to the > > > > > USB device binding (documented in devicetree/bindings/usb/usb- > > > > > device.txt) > > > > > This avoids and backwards-compatibility problems (which was a concern > > > > > regardless of the solution, see [3]) since the binding for the root-hub > > > > > was previously not specified (and we're not using the "phys" property of > > > > > the controller, which might have served different purposes before, > > > > > depending on the drivers). > > > > > > > > > > Additionally this integrates the new platform-roothub into xhci-plat.c > > > > > which automatically enables it for the dwc3 driver (in host-mode). > > > > > > > > > > > > > > > Changes since RFCv3 at [6]: > > > > > - moved the DT binding change from patch #3 to patch #1 as suggested > > > > > by Rob Herring (and slightly adjusted the commit message to account > > > > > for that) > > > > > - added Tested-by from Chunfeng Yun (who confirmed that the whole > > > > > concept and implementation works fine on Mediatek SoCs - many thanks > > > > > again!) to patch #2 > > > > > - added Rob Herring's ACK to patches 1 and 3 > > > > > - dropped RFC status (RFCv3 -> PATCH v4) > > > > > > > > I just wanted to rebase this to v4.14-rc1 (now that this is out) - > > > > however I noticed that v4 still applies to v4.14-rc1 cleanly (the > > > > patches are still identical to v4 after rebasing). > > > > > > > > we have an ACK from the devicetree maintainers and a "Tested-by" for a > > > > Mediatek (= non-Amlogic) SoC. > > > > I already have patches for the Amlogic GXL/GXM platforms queued, those > > > > are just waiting on this series. > > > > > > > > what is still missing to get this series into v4.15? > > > > > > Well, we couldn't do anything until 4.14-rc1 is out, now that it is, let > > > us catch up on patch review please... > > > > OK, I understand that. > > please let me know once you've caught up with the review backlog - as > > I said I would like to get this into 4.15 if nothing else comes up > > during the code-review > > This series works well on the libretech-cc (le potato) > For the series: > > Tested-by: Jerome Brunet <jbrunet@xxxxxxxxxxxx> Hey, I have one of those boards now, was just about to try to get it to work. Is this series necessary for it to run properly on 4.14-rc? thanks, greg k-h -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
