Re: [PATCH v1 3/5] dt-bindings: Add DT bindings for NVIDIA Tegra AHB DMA controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 09/27/2017 02:34 AM, Jon Hunter wrote:

On 27/09/17 02:57, Dmitry Osipenko wrote:
On 26.09.2017 17:50, Jon Hunter wrote:

On 26/09/17 00:22, Dmitry Osipenko wrote:
Document DT bindings for NVIDIA Tegra AHB DMA controller that presents
on Tegra20/30 SoC's.

Signed-off-by: Dmitry Osipenko <digetx@xxxxxxxxx>
---
  .../bindings/dma/nvidia,tegra20-ahbdma.txt         | 23 ++++++++++++++++++++++
  1 file changed, 23 insertions(+)
  create mode 100644 Documentation/devicetree/bindings/dma/nvidia,tegra20-ahbdma.txt

diff --git a/Documentation/devicetree/bindings/dma/nvidia,tegra20-ahbdma.txt b/Documentation/devicetree/bindings/dma/nvidia,tegra20-ahbdma.txt
new file mode 100644
index 000000000000..2af9aa76ae11
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/nvidia,tegra20-ahbdma.txt
@@ -0,0 +1,23 @@
+* NVIDIA Tegra AHB DMA controller
+
+Required properties:
+- compatible:	Must be "nvidia,tegra20-ahbdma"
+- reg:		Should contain registers base address and length.
+- interrupts:	Should contain one entry, DMA controller interrupt.
+- clocks:	Should contain one entry, DMA controller clock.
+- resets :	Should contain one entry, DMA controller reset.
+- #dma-cells:	Should be <1>. The cell represents DMA request select value
+		for the peripheral. For more details consult the Tegra TRM's
+		documentation, in particular AHB DMA channel control register
+		REQ_SEL field.

What about the TRIG_SEL field? Do we need to handle this here as well?


Actually, DMA transfer trigger isn't related a hardware description. It's up to
software to decide what trigger to select. So it shouldn't be in the binding.

I think it could be, if say a board wanted a GPIO to trigger a transfer.

And I think the same applies to requester... any objections?

Well, the REQ_SEL should definitely be in the binding.

Laxman, Stephen, what are your thoughts on the TRIG_SEL field? Looks
like we never bothered with it for the APB DMA and so maybe no ones uses
this.

I don't think TRIG_SEL should be in the binding, at least at present. While TRIG_SEL certainly is something used to configure the transfer, I believe the semantics of the current DMA binding only cover DMA transfers that are initiated when SW desires, rather than being a combination of after SW programs the transfer plus some other HW event. So, we always use a default/hard-coded TRIG_SEL value. As such, there's no need for a TRIG_SEL value in DT. There's certainly no known use-case that requires a non-default TRIG_SEL value at present. We could add an extra #dma-cells value later if we find a use for it, and the semantics of that use-case make sense to add it to the DMA specifier, rather than some other separate higher-level property/driver/...
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux