On Wed, Sep 20, 2017 at 10:01:21PM +0200, Jernej Skrabec wrote:
> Add documentation about Allwinner DWC HDMI TX node, found in H3 SoC.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@xxxxxxxx>
> ---
> .../bindings/display/sunxi/sun4i-drm.txt | 158 ++++++++++++++++++++-
> 1 file changed, 157 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> index 92512953943e..cb6aee5c486f 100644
> --- a/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> +++ b/Documentation/devicetree/bindings/display/sunxi/sun4i-drm.txt
> @@ -60,6 +60,40 @@ Required properties:
> first port should be the input endpoint. The second should be the
> output, usually to an HDMI connector.
>
> +DWC HDMI TX Encoder
> +-----------------------------
> +
> +The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
> +with Allwinner's own PHY IP. It supports audio and video outputs and CEC.
> +
> +These DT bindings follow the Synopsys DWC HDMI TX bindings defined in
> +Documentation/devicetree/bindings/display/bridge/dw_hdmi.txt with the
> +following device-specific properties.
> +
> +Required properties:
> +
> + - compatible: value must be one of:
> + * "allwinner,sun8i-h3-dw-hdmi"
> + - reg: two pairs of base address and size of memory-mapped region, first
> + for controller and second for PHY
> + registers.
> + - reg-io-width: See dw_hdmi.txt. Shall be 1.
> + - interrupts: HDMI interrupt number
> + - clocks: phandles to the clocks feeding the HDMI encoder
> + * iahb: the HDMI interface clock
> + * isfr: the HDMI module clock
> + * ddc: the HDMI ddc clock
> + - clock-names: the clock names mentioned above
> + - resets: phandles to the reset controllers driving the encoder
> + * hdmi: the reset line for the HDMI
> + * ddc: the reset line for the DDC
> + - reset-names: the reset names mentioned above
> +
> + - ports: A ports node with endpoint definitions as defined in
> + Documentation/devicetree/bindings/media/video-interfaces.txt. The
> + first port should be the input endpoint. The second should be the
> + output, usually to an HDMI connector.
> +
> TV Encoder
> ----------
>
> @@ -255,7 +289,7 @@ Required properties:
> - allwinner,pipelines: list of phandle to the display engine
> frontends (DE 1.0) or mixers (DE 2.0) available.
>
> -Example:
> +Example 1:
>
> panel: panel {
> compatible = "olimex,lcd-olinuxino-43-ts";
> @@ -455,3 +489,125 @@ display-engine {
> compatible = "allwinner,sun5i-a13-display-engine";
> allwinner,pipelines = <&fe0>;
> };
> +
> +Example 2:
> +
> +connector {
> + compatible = "hdmi-connector";
> + type = "a";
> +
> + port {
> + hdmi_con_in: endpoint {
> + remote-endpoint = <&hdmi_out_con>;
> + };
> + };
> +};
> +
> +de: display-engine {
> + compatible = "allwinner,sun8i-h3-display-engine";
> + allwinner,pipelines = <&mixer0>;
> +};
> +
> +hdmi: hdmi@1ee0000 {
> + compatible = "allwinner,h3-dw-hdmi";
> + reg = <0x01ee0000 0x10000>,
> + <0x01ef0000 0x10000>;
> + reg-io-width = <1>;
> + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI>,
> + <&ccu CLK_HDMI_DDC>;
> + clock-names = "iahb", "isfr", "ddc";
> + resets = <&ccu RST_BUS_HDMI0>, <&ccu RST_BUS_HDMI1>;
> + reset-names = "hdmi", "ddc";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + hdmi_in: port@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + hdmi_in_tcon0: endpoint@0 {
> + reg = <0>;
You don't need reg when there's only one.
Otherwise,
Acked-by: Rob Herring <robh@xxxxxxxxxx>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
