On Wed, Sep 13, 2017 at 04:07:47PM +0100, Dave Stevenson wrote:
> Document the DT bindings for the CSI2/CCP2 receiver peripheral
> (known as Unicam) on BCM283x SoCs.
>
> Signed-off-by: Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/media/bcm2835-unicam.txt | 107 +++++++++++++++++++++
> 1 file changed, 107 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/bcm2835-unicam.txt
>
> diff --git a/Documentation/devicetree/bindings/media/bcm2835-unicam.txt b/Documentation/devicetree/bindings/media/bcm2835-unicam.txt
> new file mode 100644
> index 0000000..2ee5af7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/bcm2835-unicam.txt
> @@ -0,0 +1,107 @@
> +Broadcom BCM283x Camera Interface (Unicam)
> +------------------------------------------
> +
> +The Unicam block on BCM283x SoCs is the receiver for either
> +CSI-2 or CCP2 data from image sensors or similar devices.
> +
> +There are two camera drivers in the kernel for BCM283x - this one
> +and bcm2835-camera (currently in staging).
Linux detail that is n/a for bindings.
> +
> +This driver is purely the kernel controlling the Unicam peripheral - there
Bindings describe h/w blocks, not drivers.
> +is no involvement with the VideoCore firmware. Unicam receives CSI-2
> +(or CCP2) data and writes it into SDRAM. There is no additional processing
> +performed.
> +It should be possible to connect it to any sensor with a
> +suitable output interface and V4L2 subdevice driver.
> +
> +bcm2835-camera uses the VideoCore firmware to control the sensor,
> +Unicam, ISP, and various tuner control loops. Fully processed frames are
> +delivered to the driver by the firmware. It only has sensor drivers
> +for Omnivision OV5647, and Sony IMX219 sensors, and is closed source.
> +
> +The two drivers are mutually exclusive for the same Unicam instance.
> +The firmware checks the device tree configuration during boot. If
> +it finds device tree nodes called csi0 or csi1 then it will block the
> +firmware from accessing the peripheral, and bcm2835-camera will
> +not be able to stream data.
All interesting, but irrelavent to the binding other than the part about
node name. Reword to just state the requirements to get the firmware to
ignore things.
> +It should be possible to use bcm2835-camera on one camera interface
> +and bcm2835-unicam on the other interface if there is a need to.
For upstream, I don't think we care to support that. We don't need 2
bindings.
> +
> +Required properties:
> +===================
> +- compatible : must be "brcm,bcm2835-unicam".
> +- reg : physical base address and length of the register sets for the
> + device.
> +- interrupts : should contain the IRQ line for this Unicam instance.
> +- clocks : list of clock specifiers, corresponding to entries in
> + clock-names property.
> +- clock-names : must contain an "lp_clock" entry, matching entries
> + in the clocks property.
_clock is redundant.
> +
> +Unicam supports a single port node. It should contain one 'port' child node
> +with child 'endpoint' node. Please refer to the bindings defined in
> +Documentation/devicetree/bindings/media/video-interfaces.txt.
> +
> +Within the endpoint node, the following properties are mandatory:
> +- remote-endpoint : links to the source device endpoint.
> +- data-lanes : An array denoting how many data lanes are physically
> + present for this CSI-2 receiver instance. This can
> + be limited by either the SoC itself, or by the
> + breakout on the platform.
> + Lane reordering is not supported, so lanes must be
> + in order, starting at 1.
Just refer to docs for standard properties. Just add any info on limits
of values like number of cells.
> +
> +Lane reordering is not supported on the clock lane, so the optional property
> +"clock-lane" will implicitly be <0>.
> +Similarly lane inversion is not supported, therefore "lane-polarities" will
> +implicitly be <0 0 0 0 0>.
> +Neither of these values will be checked.
> +
> +Example:
> + csi1: csi@7e801000 {
I thought the node had to be called csi0 or csi1. The label (csi1) will
be gone from the compiled dtb.
> + compatible = "brcm,bcm2835-unicam";
> + reg = <0x7e801000 0x800>,
> + <0x7e802004 0x4>;
> + interrupts = <2 7>;
> + clocks = <&clocks BCM2835_CLOCK_CAM1>;
> + clock-names = "lp_clock";
> +
> + port {
> + #address-cells = <1>;
> + #size-cells = <0>;
Don't need these with a single endpoint.
> +
> + csi1_ep: endpoint {
> + remote-endpoint = <&tc358743_0>;
> + data-lanes = <1 2>;
> + };
> + };
> + };
> +
> + i2c0: i2c@7e205000 {
> +
> + tc358743: csi-hdmi-bridge@0f {
> + compatible = "toshiba,tc358743";
> + reg = <0x0f>;
> + status = "okay";
Don't show status in examples.
> +
> + clocks = <&tc358743_clk>;
> + clock-names = "refclk";
> +
> + tc358743_clk: bridge-clk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <27000000>;
> + };
> +
> + port {
> + tc358743_0: endpoint {
> + remote-endpoint = <&csi1_ep>;
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + clock-noncontinuous;
> + link-frequencies =
> + /bits/ 64 <297000000>;
> + };
> + };
> + };
> + };
> --
> 2.7.4
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
